EZCOO EZ-MX42HS User manual

User Manual
EZ-MX42HS
4K@60 4:4:4 8bit
Scaler Output
Dolby Vision
Dolby Atmos
HDR
EZCOO - It’s easy, Just cool

This Matrix 4x2 is 4 IN 2 OUT HDMI Matrix with Ultra HD up to 4K@60Hz
4:4:4 8bit HDR and HDCP2.2,support Dolby vision and Dolby atmos.It reliably
distributes four HDMI source signal to two HDMI display devices, ideally use for
ofces,school,conference rooms,shopping malls,hotels and museums, which require to
distribute and switch multiple HDMI source signal to two HDMI display devices.
1. HDMI Matrix x1 2. Power Adapter x1
3. Mounting Ear x2 4. HOOK&LOOP x2
5. Reusable Cable Tie x2 6. User Manual x1
• Distributes four HDMI sources signal to two HDMI display devices. It supports 4K
and 1080P output simultaneously.
• Supports HDMI 2.0 4K@60Hz 4:4:4 8bit HDR, HDCP 2.2.
• Supports Dolby vision.
• Supports EDID copy, multiple EDID setting for compatibility.
• Supports 3D, Support deep color 30bit, 36bit.
• Supports Blue-Ray 24/50/60fs/HD-DVD/xvYCC.
• Supports HDMI signal re-timing, never lose quality.
• Support Dolby atmos,Dolby HD Audio and DTS HD audio.
• Plug and Play; No driver required; Installs in minutes.
• Support remote control, button control.
OVERVIEW
PACKING LIST
FEATURES

1. Connect one cable from HDMI source devices to each HDMI input.
2. Connect one cable from each display (monitor or projector) to the HDMI outputs.
Both HDMI OUT ports support downscaler 4K to 1080P, you have to implement it via
the EDID switch or the scaler switch on the front panel. For more informations about the
EDID and scaler setting, please refer to the next section.
INSTALLATION and INSTRUCTION

EDID SETTING
SCALER SETTING
Switch setting Function
Switch setting Function Switch setting Function
Note: Other options about EDID setting, please kindly use the API
commonds(Refer to the last section API Commands list).
Set EDID:
4K@60Hz_4:4:4_Dolby vision_Dolby Atmos_7.1CH_3D-HDR
OUTPUT1 pass through.
OUTPUT2 pass through.
OUTPUT1 downscaler from
4k to 1080P.
OUTPUT2 pass through.
Set EDID:
1080P@60Hz_2CH_3D_HDR
OUTPUT 1 pass through.
OUTPUT 2 downscaler from
4k to 1080P.
OUTPUT1 downscaler from
4k to 1080P.
OUTPUT 2 downscaler from
4k to 1080P.
Learning EDID from HDMIOUT 1

REMOTE CONTROL
The remote control can be used to
turn on and off the matrix and switch
the HDMI source for each output.
Note：
• Please remove the insulation
slice before use.
• Please make sure the remote
is pointed directly at the IR
receiver windown.
HDMI vertion HDMI 2.0 HDCP version HDCP 2.2
HDMI
resolution
4K*2K/1080p
/1080i/720p/576p/576i/480p/480i Video format 24bit/30bit, 36bit deep color
Audio format Dolby Atmos/Dolby true HD/DTS-HD/LPCM7.1/Dolby-AC3/DSD
Input/Output
TMDS signal 0.5~1.5Volts p-p(TTL) Max bandwidth 600MHz
Input/Output
DDC signal 5Volts p-p (TTL) Max working current 1.5A
Power adapter
format
Input: AC (50HZ, 60HZ):100V-
240V; Output: DC5V/2A Max baud rate 6Gbps
Operating
Temperature
range
(-15 to +55℃)
Operating
Humidity
range
5 to 90%RH
Dimension
(L x W x H) 180*84*16(mm) Weight 380g
General
SPECIFICATION

Cable
HDMI Cable
Length
1080P 4K
8-bit 12-bit 8-bit
Input 49.2 ft (15m) 32.8ft (10m) 9.8ft (3m)
Output 49.2 ft (15m) 32.8ft (10m) 16.4ft (5m)
How to use the Micro-USB on the front panel.We can control the matrix and upgrade
the matrix via this port.Please nd a Micro-USB cable, connect to the USB port on the
front panel to your windows PC(Laptop/Desktop).It will install the driver aromatically
when the matrix connected, please wait for a minute.
Please download Firmware Upgrade Tool at easycoolav.
com, then refer to below Firmware Upgrade Instruction.
Baud Rate=57600bps, Data=8bit, Parity=None, Stop=1bit
Double click the UartAssist.exe. Set the correct parameters
and click <Open>
You can also use the RS232 port for upgrating.
UPDATE GUIDE
Upgrade
1. Send a command <ISP 32 1> +Enter,
then click <Send> button.

After you sent this command, you will see <JUMP TO ISP MODE...>, and then click
<Close>
All LEDs on the matrix will be off.
NOTE: DO NOT remove any connection on the matrix at this time.
2. Running < STM Flash Loader Demo>
Select correct port and click <next>
3. Target is readable. Please click "Next" to proceed.
4. Select 128K and <next>

5. Finish and repower the matrix.

The conguration steps are the same as UPGRADE section.
Send “EZH” to get all API commands.
API Command via USB port/RS232 port
Command Function
EZH Get help, show all the commands
EZS RST Reset to Factory Defaults
EZS CAS EN Set Cascade Mode Enable (HDCP)
EZS CAS DIS Set Cascade Mode Disable (HDCP)
EZS OUTx VS INy Set Output x To Input y {x=[0~2](0=ALL), y=[1~4]}
EZS OUT1 VIDEOy Set Output 1 VIDEO Mode y {y=[1~2](1=BYPASS,2=4K->2K)scaler}
EZS OUT2 EXA EN Set Ex-Audio Output Enable
EZS OUT2 EXA DIS Set Ex-Audio Output Disable
EZS OUTx STREAM ON Set Output x Stream ON{x=[0~2](0=ALL)}Turn ON HDMI OUTPUT
EZS OUTx STREAM
OFF
Set Output x Stream OFF{x=[0~2](0=ALL)}Turn OFF HDMI
OUTPUT
EZS INx EDIDy Set EDID of HDMI input {x=[0~4](0=ALL), y=[1~16]}
EDID LIST 1-1080P60Hz_2CH(PCM)_HDR
2-1080P60Hz_6CH_HDR
3-1080P60Hz_8CH_HDR
4-1080P_3D_2CH(PCM)_HDR
5-1080P_3D_6CH_HDR
6-1080P_3D_8CH_HDR
7-4K30Hz_3D_2CH(PCM)_HDR
8-4K30Hz_3D_6CH_HDR
9-4K30Hz_3D_8CH_HDR
10-4K60Hz(Y420)_3D_2CH(PCM)_HDR
11-4K60Hz(Y420)_3D_6CH_HDR
12-4K60Hz(Y420)_3D_8CH_HDR
13-4K60Hz(Y444)_3D_2CH(PCM)_HDR
14-4K60Hz(Y444)_3D_6CH_HDR
15-4K60Hz(Y444)_3D_8CH_HDR
16-4K60 Dolby_Vision_Atoms
17- USER EDID
List of API Commands

When you want to set EDID as 4K@60Hz 7.1CH, please send a command "EZS IN0
EDID15" as follows.
Example

The information in this manual has been carefully checked and is
believed to be accurate. EZCOOTECH assumes no responsibility for any infringement
of patents or other rights of third parties which may result from its use.
EZCOOTECH assumes no responsibility for any inaccuracies that may be contained in
this document. EZCOOTECH also makes no commitment to update or to keep current
the information contained in this document. EZCOOTECH reserves the right to make
improvements to this document and/or product at any time and without notice.
When you need any technical assistance, please send e-mail to
[email protected]
NOTES
DISCLAIMERS
CONTACTS
Please use this machine based on below instructions to keep longer lifetime.
1. The machine should be placed at the spot far away from the Damp,
High-Temperature, Dusty, Erosive, and Oxidant environment.
2. All parts will be free from the strong shake, hit, fall.
3. Touching the device with the wet hands is prohibited.
4. Please turn power off when machine is not used for long time.
5. Please do not open the cover and do not touch the inside parts.
6. Please use the original factory power adaptor.
7. Before power on, please check the connection cable carefully. And make sure that all
interfaces are normally connected.

EZCOO - It’s easy, Just cool