FAAC XTR B INOX User manual

XTR B
EN

XTR B 2 532109 - Rev.A
© Copyright FAAC S.p.A. ab dem 2017. Alle Rechte
vorbehalten.
Kein Teil dieses Handbuchs darf reproduziert, ge-
speichert, an Dritte weitergegeben oder sonst auf
eine beliebige Art in einem beliebigen Format und
mit beliebigen Mitteln kopiert werden, weder mit
elektronischen, noch mechanischen oder durch Fo-
tokopieren, ohne die Genehmigung von FAAC S.p.A.
Alle erwähnten Namen und Marken sind Eigentum
der jeweiligen Hersteller.
Die Kunden dürfen nur für den Eigengebrauch
Kopien anfertigen.
Dieses Handbuch wurde 2017 veröffentlicht.
© Copyright FAAC S.p.A. from 2017. All rights
reserved.
Nopart of thismanualmaybereproduced,archived,
distributed to third parties nor copied in any other
way, in any format and with any means, be it
electronic, mechanical or by photocopying, without
prior written authorisation by FAAC S.p.A.
All names and trademarks mentioned are the pro-
perty of their respective manufacturers.
Customers may make copies exclusively for their
own use.
This manual was published in 2017.
©CopyrightFAACS.p.A. del 2017.Todos los derechos
están reservados.
No puede reproducirse, archivarse, distribuirse a
terceros ni copiarse de ningún modo, ninguna parte
de este manual, con medios mecánicos o mediante
fotocopia, sin el permiso previo por escrito de
FAAC S.p.A.
Todos los nombrey las marcas citadas son de propie-
dad de los respectivos fabricantes.
Los clientes pueden realizar copias para su uso
exclusivo.
Este manual se ha publicado en 2017.
© Copyright FAAC S.p.A. depuis 2017. Tous droits
réservés.
Aucunepartie decemanuelnepeut êtrereproduite,
archivéeou distribuée à des tiersnicopiée,soustout
format et avec tout moyen, qu’il soit électronique,
mécaniqueouparphotocopie,sansleconsentement
écrit préalable de FAAC S.p.A.
Tous les noms et les marques cités sont la propriété
de leurs fabricants respectifs.
Les clients peuvent faire des copies pour leur usage
exclusif.
Ce manuel a été publié en 2017.
© Copyright FAAC S.p.A. dal 2017. Tutti i diritti
riservati.
Nessuna parte di questo manuale può essere ripro-
dotta, archiviata, distribuita a terzi né altrimenti
copiata, in qualsiasi formato e con qualsiasi mezzo,
sia esso elettronico, meccanico o tramite fotocopia,
senza il preventivo consenso scritto di FAAC S.p.A.
Tutti i nomi e i marchi citati sono di proprietà dei
rispettivi fabbricanti.
I clienti possono effettuare copie per esclusivo
utilizzo proprio.
Questo manuale è stato pubblicato nel 2017.
© Copyright FAAC S.p.A. van 2017. Alle rechten
voorbehouden.
Niets uit deze handleiding mag gereproduceerd,
gearchiveerd, aan derden openbaar gemaakt of
op andere wijze gekopieerd worden, in om het
even welke vorm en met geen enkel middel, noch
elektronisch,mechanisch of via fotokopiëren,zonder
schrfitelijke toestemming vooraf van FAAC S.p.A.
Alle vermelde namen en merken zijn eigendom van
de respectievelijke fabrikanten.
De klanten mogen kopieën maken die enkel voor
eigen gebruik bestemd zijn.
Dez handleiding werd in 2017 gepubliceerd.

XTR B 01 532109 - Rev.A
B
E
A
C
D
Made in Ireland
2051
13.56 MHz
786040
B
E
A
C
D
Étiquette d'identification du produit
A.Code d'identification du modèle
B.Lire les instructions
C. Éliminer selon les directives en vigueur
D. Référence Notified Body
E. Fréquence
Produkt-Identifikationsetikett
A.Indentifikations-Code des Modells
B.Die Anweisungen lesen.
C. Gemäß den geltendenVorschriften entsorgen
D. Referenz Notified Body
E. Frequenz
Etiqueta de identificación del producto
A.Código de identificación del modelo
B.Leer las instrucciones
C. Eliminar según las directivas vigentes
D. Referencia Notified Body
E. Frecuencia
Identificatielabel product
A.Identificatiecode van het model
B.De instructies doorlezen
C. Verwijder in overeenstemming met de gel-
dende richtlijnen
D. Referentie Aangemelde Instantie
E. Frequentie
Etichetta di identificazione prodotto
A.Codice identificativo del modello
B.Leggere le istruzioni
C. Smaltire secondo le direttive vigenti
D. Riferimento Notified Body
E. Frequenza
Product identification plate
A.Model identification code
B.Operating instructions
C. Dispose in accordance with current regulations
D. Notified body reference
E. Frequency

XTR B 02 532109 - Rev.A
Ø 4 mm
1
Ø 4 mm
MAX 45°

!
MAX 45°

!

Ø 15 mm

Ø 15 mm
• XTR B INOX •
• XTR B •
GuarnizioneditenutaIP•IPsealinggasket
•Jointd'étanchéitéIP•IPDichtung•Junta
de estanqueidad IP • IP-afdichting
GuarnizioneditenutaIP•IPsealinggasket
•Jointd'étanchéitéIP•IPDichtung•Junta
de estanqueidad IP • IP-afdichting

XTR B 03 532109 - Rev.A
2
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
(A)
(B)
BUS 2easy
MAX 100 m
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
SW1
Dip-switch • Dip-switch • Dip-switch • Dip-Schalter • Dip-switch • DIP-schakelaar
SW2
Pulsante • Button • Bouton • Taste • Botón • Drukknop
J5
Jumper • Jumper • Jumper • Jumper • Jumper • Jumper
J7
BUS 2easy Morsetti • BUS 2easy Terminals • BUS 2easy bornes • BUS 2easy Klemmen •
BUS 2easy Bornes • BUS 2easy Aansluitklemmen
BZ1
Buzzer • Buzzer • Buzzer • Buzzer • Zumbador • Buzzer
DL2 DL3
Led • LED • Led • LED • Led • Led
-0.5mm2Sezione MAX dei cavi • MAX section of cables • Section MAX des câbles • MAX Querschnitt der
Kabel • Sección MÁX. de los cables • MAX doorsnede kabels
-La linea BUS non ha polarità • The BUS line does not require a matching polarity connection • La ligne
BUS n'a pas de polarité • Die BUS Leitung hat keine Polarität • La línea BUS no tiene polaridad • De
BUS-lijn heeft geen polariteit

XTR B 04 532109 - Rev.A
3
• XTR B INOX •
• XTR B •
Guarnizione di tenuta IP • IP
sealing gasket • Joint d'étanc-
héité IP • IP Dichtung • Junta de
estanqueidad IP • IP-afdichting
Guarnizione di tenuta IP • IP
sealing gasket • Joint d'étanc-
héité IP • IP Dichtung • Junta de
estanqueidad IP • IP-afdichting

XTR B 05 532109 - Rev.A
4
5
5
click
• XTR B INOX •
• XTR B •

XTR B 06 532109 - Rev.A
6
7
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
DL2 DL3
SW1
BZ1
J7
J5
SW2
ON
1 2 3 4 5
XTR B (A) XTR B (B) 
AB
BUS-RELAY4CHBUS 2easy BUS-RELAY2CH
-1CH max 14 XTR B
-2CH max 4XTR B 1CH/2CH max 4 XTR B
XTR B (1CH)
XTR B (2CH)
Tag-Group2
Tag-Group3
Tag-Group4
Tag-Group1 R1
R2
R3
R4
Tag-Group1 R1
R2
Tag-Group2 R3
R4
A
B
A
B
R1
R2
R1
R2
R3
R4

XTR B 1 532109 - Rev.A
CONTENTS
1. XTR B ....................................................................................................... 2
Technical data........................................................................................... 3
2. SAFETY INFORMATION ................................................................................... 4
3. INSTALLATION.............................................................................................4
3.1 Connecting to the board with BUS 2easy .............................................................. 5
Configuring the dip-switches.......................................................................... 5
First storage of Tags .................................................................................... 6
3.2 Connecting to a BUS-RELAY interface .................................................................. 7
Configuring the dip-switches.......................................................................... 7
Assigning the Tags to the Relays....................................................................... 7
First storage of a Tag-Group ........................................................................... 8
4. DELETING ALL TAGS....................................................................................... 9
5. DELETING A TAG GROUP.................................................................................. 9
6. TROUBLESHOOTING .................................................................................... 10
7. REPLACING THE XTR B.................................................................................. 10
8. USAGE .................................................................................................... 11
1CH mode: 1 command ................................................................................11
2CH mode: 2 commands...............................................................................11
9. ADDING TAGS............................................................................................ 13
10. MAINTENANCE......................................................................................... 13
EN
Translation of the original instructions
CE DECLARATION OF CONFORMITY
The Manufacturer
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares on his sole responsibility that the following products:
Description: Tag reader
Models: XTR B, XTR B INOX
comply with the following applicable EU legislations:
RED Directive 2014/53/EU
ROHS 2 Directive 2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013
EN 62311:2008
EN 301 489-1V1.9.2 + EN 301 489-3 V1.6.1
EN 302 291-2V1.1.1
Bologna, 01-01-2017 CEO

XTR B 2 532109 - Rev.A
!This device cannot be used as an emer-
gency stop.
This device cannot be used as the main-
tained command in the dead-man mode
of operation.
Commands. If the XTR B is connected to the
BUS 2easy of a board, the commands are defined
by the dip-switches on the reader. If the XTR B
is connected to a BUS-RELAY interface, the relay
outputs must be associated with the Tags at the
time they are stored.
Firststorageprocedure. Thisprocedureis restricted
to the installer and must be carried out in order
to enable the first Tag and to store its code on the
reader. Other Tags can be stored before finishing
the procedure.
All Tags enabled during the First storage procedure
are Master tags.
Add Tags. This procedure allows additional Tags
to be enabled subsequently to the first storage
procedure.
In order to add additional Tags, you must have a
MasterTag that has alreadybeen storedandbeclose
to the reader (without having to open it).
Tags can be added as either Master or Slave tags.
Slave tags cannot be used to enable the addition
ofTags.
XTR B_A/XTR B_B. Each tag always transmits two
distinct codes: A and B. The position of the jumper
on the reader determines whether the reader rec-
ognises code A or code B. In this way, a Tag can be
enabled with code A on one system and code B on
another system. For example: ATag enabled with
code A on the XTR B of a condominium entrance
and with code B on the XTR B of a private entrance.
1. XTR B
The XTR B Tag reader is included in the range of
BUS 2easy controldevices. Therangealso includes,
for example, key operated switches and key pads
(see catalogue).
The XTR B only recognises dedicated FAAC Tags
(see catalogue). A limited number of Tags can
be enabled.
Connection. The XTR B can be connected to:
-Electronic board with BUS 2easy
-BUS-RELAY 2CH interface
-BUS-RELAY 4CH interface
When the XTR B is switched on, it automatically
recognises the type of connection.
The boards with BUS 2easy that are compat-
ible or incompatible with the XTR B are indicated
below. Some boards are compatible only if the
firmwarehasbeenupdatedtothe versionsindicated
(FW) or later(refertothe instructionsof the updated
boards) TheboardswithBUS 2easy that arenot
listed are always compatible.
Compatible boards [revision] FW
E045 [previous to 1L] 1.7
E045 [1L and later] 3.2
E145 [previous to 1R] 2.0
E145 [1R and later] 3.2
E124 [all] 3.2
E721 [all] 2.9
624BLD [all] 2.1
E680 [all] 2.1
JE275 [all] 2.1
Incompatible boards: E700, E720, E024, E391
, E012S, E850.
Operation. TheTagtransmitsitscodewhenbrought
close to the reader. When the reader recognises
an enabled Tag, it transmits the command via the
BUS 2easy line.
TheXTRB worksin the mode set via the dip-switches
on the device. The choice is between:
-Single channel (XTR B_1CH) the Tag has only
1 command
-Two-channel (XTR B_2CH) the Tag has 2
commands
With the XTR B_2CH, the activation of the first or
second command depends on the mode in which
theTag is used on the reader (see § 8).
The Tag can be used for an impulse command or a
maintained action command.

XTR B 3 532109 - Rev.A
Connection type Mode (§Dip-switch con-
figuration) No. of control devices that can be connected
Board with BUS 2easy 1CH
2CH max 14* max 4* * Theoretical no.: The actual
number of control devices that
canbe connecteddependsonthe
total absorbed power of all the
accessories and the maximum
current that can be supplied by
the board.
BUS-RELAY 4CH interface 1CH
2CH max 4* max 4*
BUS-RELAY 2CH interface 1CH
2CH max 4* max 2*
TECHNICAL DATA
power supply BUS 2easy line
MAX power consumption 50 mA
ingress protection IP 54
operating temperature -20°C +55°C
dimensions 100 x 72 x 21 mm
Tag format ISO15693
Symbols used in the instructions
! Risk of personal injury or damage to
components
F electrocution hazard
§ chapter/section: e.g. § 1 = Chap.1
 figure: e.g. 1 = Fig.1
 page: e.g. 1 = Page 1
 table: e.g. 1 =Tab.1
1CH single channel ; 2CH two-channel
 time indicator
 (BEEP)Audible signal
 Led off  Led on
 Flashing  Fast flashing

XTR B 4 532109 - Rev.A
2. SAFETY INFORMATION
!The packaging materials (plastic, polysty-
rene, etc.) must not be left within reach
of children as they are potential sources
of danger.
FAlways switch off the electricity supply
before making electrical connections.
When you have finished with them, dis-
pose of the packaging in the appropriate
containers,asper applicable wastedisposal
regulations.
The electronic components must not be
disposed of in landfill, but should be taken
to an authorised disposal and recycling
centre,incompliancewith applicable waste
disposal legislation.
3. INSTALLATION
1. Prepare the connecting cables and install the
base. Follow the instructions in 1.
2. Connect to the BUS 2easy terminals on the
board or the BUS-RELAY interface. Follow the
instructions in 2.
3. Position the jumper to specify reader Aor B:
-J5 closed = XTR B_A
-J5 open = XTR B_B
4. Configure the dip-switches according to the
connection:
-Board with BUS 2easy: see § 3.1
-BUS-RELAY interface: see § 3.2
5. Switch power on to the electronic board with
BUS 2easy or the BUS-RELAY interface.
-The XTR B flashes once, then the LEDs turn
off: XTR B in standby.
6. Register the BUS 2easy devices (see board or
interface instructions).
7. Carry out the first storageprocedureaccordingto
the type of connection:
-Board with BUS 2easy: see 6
-BUS-RELAY interface: see 8
8. Make sure that all tags are working correctly for
all enabled commands.
9. Fasten the body to the base (3) and put the
cover on (4- 5).
!The IP sealing gasketsin the base and in the
body must be fitted and intact.

XTR B 5 532109 - Rev.A
ON
1 2 3 4 5
Dip 5 = OFF
ON
1 2 3 4 5
Dip 5 = ON
1 = ON ; 0 = OFF
1 1CH mode
3.1 CONNECTING TO THE BOARD WITH
BUS 2EASY
CONFIGURINGTHE DIPSWITCHES
Position the dip-switches (1 or 2) in order
to specify:
-1CH or 2CH mode of operation (Dip-switch 5)
-the commands that the XTR B transmits to the
board (Dip-switches 1-2-3-4)
!For each control device connected to the
BUS2easyline,positionthedip-switchesso
thata commandisusedonlyon one device.
In order to add an XTR B to an existing sys-
tem you must know which commands are
alreadyused on the other BUS 2easy devices
that are present. See the instructions for
the devices that are already installed in
2 2CH mode
ordertoidentifywhichcommandsarealready
used. For future reference, you can make a
note of the IDs of the installed devices in
the table at the end of this manual. Any
BUS 2easy photocells or BUS 2easy safety
edges do not interfere with the control de-
vices.Their dip-switches can be ignored.
Dip-switch
1 2 3 4
command
0 0 0 0 Open A_1
0 0 0 1 Open A_2
0 0 1 0 Open A_3
0 0 1 1 Open A_4
0 1 0 0 Open A_5
0 1 0 1 Stop
0 1 1 0 Stop NC*_1
0 1 1 1 Stop NC*_2
1 0 0 0 Close
1 0 0 1 Open B_1
1 0 1 0 Open B_2
1 0 1 1 Open B_3
1 1 0 0 Open B_4
1 1 0 1 Open B_5
1 1 1 0 not used
1 1 1 1 not used
Dip-switch
1 2 3 4
Command 1 Command 2
0 0 0 0 Open A_1 Open B_1
0 0 0 1 Open A_1 Open B_2
0 0 1 0 Open A_1 Stop
0 0 1 1 Open A_1 Close
0 1 0 0 Open A_2 Open B_1
0 1 0 1 Open A_2 Open B_2
0 1 1 0 Open A_2 Stop
0 1 1 1 Open A_2 Close
1 0 0 0 Open A_3 Open B_3
1 0 0 1 Open A_3 Open B_4
1 0 1 0 Open A_3 StopNC*_1
1 0 1 1 Open A_3 Close
1 1 0 0 Open A_4 Open B_3
1 1 0 1 Open A_4 Open B_4
1 1 1 0 Open A_4 StopNC*_2
1 1 1 1 Open A_4 Close
* StopNC, also generates a Stop when the XTR B is disconnected.

XTR B 6 532109 - Rev.A
4
SW2 SW2
1


2


3


FIRST STORAGE PROCEDURE
First MasterTag
Additional MasterTags
FIRST STORAGE OF TAGS
The XTR B must be in standby. The memory must
be empty.
1. Press and release the button once.
-After2 s,the XTR BwillBEEPonceandflashonce.
-It will flash for 20 s (storing enabled).
2. Bring the firstTag up to the reader.
-The XTR B will BEEP once and the LEDs will come
on for 2 s: theTag is enabled.
-Flashing will resume for 10 s (storing enabled).
3. Repeat step 2for any additional Master Tags
required.
4. To finish, let 10 s pass without bringing any
new Tags up to the reader (or press the button
immediately).
-The LEDs turn off: XTR B in standby.
Errors during storage process Solution
During step 1, the XTR B signals
anerrorandturnsoffinstandby:
the button has been pressed
more than once
Repeat the pro-
cess correctly
During step 1, the XTR B signals
anerrorandturnsoffinstandby:
the memory is not empty
Carryoutthe"Add
Tag" or "Total De-
letion" process
During step 3, the XTR B signals
an error, then the LEDs turn off:
theTag has not been stored
Carryoutthe"Add
Tag" process
ERROR warning: Five BEEPS and 5 flashes
in quick succession.
timeout withoutTag: END
...20 s MAX
1+2 s: Tag OK , 10 s (timeout)
1+2 s: Tag OK , 10 s timeout
...10 s MAX
2 s 1() , 20 s (timeout)

XTR B 7 532109 - Rev.A
ON
1 2 3 4 5
Dip 5 = OFF
1CH
ON
1 2 3 4 5
Dip 5 = ON
2CH
3.2 CONNECTING TO A BUSRELAY
INTERFACE
CONFIGURINGTHE DIPSWITCHES
Positionthedip-switches ( 3) in ordertospecify:
-1CH or 2CH mode of operation (Dip-switch 5)
-ID device identifier (Dip-switches 1-2)
Dip-switches 3-4 are irrelevant.
!Each control device connected to the BUS
line must have a different ID.
In order to add an XTR B to an existing
system you must know the IDs of the other
BUS 2easy devices that are present. See
the instructions for the devices already
installed in order to identify the IDs that
have already been used.
Forfuturereference,youcanmakea note of
the IDs of the installed devices in the table
at the end of this manual.
ASSIGNING THETAGS TO THE RELAYS
Insinglechannel mode (1CH), each enabled Tag can
activateonly onerelay. Therelayis assignedduring
the storage phase by selecting a Group.
In two channel mode (2CH), each enabled Tag can
activate 2 relays (not simultaneously). The pair
of relays is assigned during the storage phase by
selecting a Group. TheTag activates one relay with
command1 and the other with command2 (see § 8).
CORRESPONDENCE BETWEEN GROUP/RELAY
 3 ID in 1CH or 2CH mode
Dip-switch
1 2 3 4 ID Groups available in 1CH mode Groups available in 2CH mode
0 0 x x ID1 1 , 2 , 3 , 4 1 , 2
0 1 x x ID2 1 , 2 , 3 , 4 1 , 2
1 0 x x ID3 1 , 2 , 3 , 4 1
1 1 x x ID4 1 , 2 1
Group 1
Group 2
Group 3
Group 4
XTR B (1CH) Relay 1
XTR B (2CH)
Command 1 Relay 1
Command 2 Relay 2
XTR B (1CH) Relay 2
XTR B (2CH)
Command 1 Relay 3
Command 2 Relay 4
XTR B (1CH) Relay 4
XTR B (1CH) Relay 3
1 = ON ; 0 = OFF ; x = irrelevant

XTR B 8 532109 - Rev.A
4
SW2 SW2
1


2


3


FIRST STORAGE OF A TAGGROUP
TheXTRBmust be instandby. Thememory of the
Group selected must be empty.
1. Select the group: press the button the same
number of times as the number of the Group
(eg.: Group 3, press 3 times).
-After 2 s, the XTR B will BEEP and flash the same
number of times as the number of the Group.
-It will flash for 20 s (storing enabled).
2. Bring theTag close to the reader.
-TheXTRBwillBEEPthe same number of timesas
the number of the Group and the LEDs will come
on for 2 s: theTag is enabled.
-Flashing will resume for 10 s (storing enabled).
3. Repeatstep2foranyadditionalMasterTags that
are required for the Group.
-The XTR B will BEEP once and the LEDs will
come on for 2 s after each additional Tag has
been enabled.
4. To finish, let 10 s pass without bringing any
new Tags up to the reader (or press the button
immediately).
-The LEDs turn off: XTR B in standby.
Repeat the procedure to enable one or more tags of
anotherGroup. Atstep 1,assign an availableGroup.
Errors during storage process Solution
During step 1, the XTR B signals
an error, then the LEDs turn off:
Group not available
Repeattheprocess
correctly
Duringstep1,afteraBEEPorse-
ries of BEEPS equal to the group
number, XTR B memorisation is
not active (LEDs on, NO flashing
for20secs):the groupisalready
stored in the memory
Carry out the“Add
Tag” process for
the group
During step 3, the XTR B signals
an error, then the LEDs turn off:
the Tag has not been stored in
the memory
Carry out the“Add
Tag” process for
the group
ERROR warning: Five BEEPS and 5 flashes
in quick succession.
FIRST STORAGE OF ATag-GROUP
Ntimes (N = Group number)
FirstMasterTagof the Group
Additional Master Tag of
the Group
timeout withoutTag: END
...20 s MAX
N +2 s: Tag OK , 10 s (timeout)
1+2 s: Tag OK , 10 s timeout
...10 s MAX
2 s N() , 20 s (timeout)

XTR B 9 532109 - Rev.A
SW2
2
3SW2
SW2 ~ 20 s
2
2 s 1 , 10s , 10 s ,
1+ 1 s , 
SW2 ~20 s
1
SW2 SW2
1
2 s N() , 
1, 10s , 10 s , 1+1 s , 


Ntimes (N = Group number)
4. DELETING ALL TAGS
!This procedure permanently deletes allTags from memory.
TOTAL DELETION
DELETING a GROUP
The XTR B must be in standby.
1. Press and hold the button throughout the entire
sequence:
-After 2 s the XTR B will BEEP once and starts to
flash for 10 s. The frequency of flashing then
increases for another 10 s. Finally the XTR B will
BEEP once and the LEDs turn on for 1 s: theTags
have been deleted.
-The LEDs turn off: XTR B in standby.
2. Release the button.
To interrupt the deletion procedure, release the
button before the BEEP in step 1. The LEDs turn
off: XTR B in standby.
5. DELETING A TAG GROUP
!This procedure permanently deletes all theTags of the Group. The procedure is only active if the
XTR B is connectedtoaBUS-RELAYinterface. In other cases,carry out theTotal Deletionprocedure
The XTR B must be in standby.
1. Select the Group to delete: press the button
the same number of times as the number of the
Group (e.g.: Group 3, press 3 times).
-After 2 s, the XTR B will BEEP and flash the
same number of times as the number of the
Group. Then the LEDs will turn on steadily.
2. Press and hold the button throughout the entire
sequence:
-The XTR B will BEEP once and starts to flash for
10 s. The frequency of flashing then increases
for another 10 s. Finally the XTR B will BEEP
once and the LEDs turn on for 1 s: the Group has
been deleted.
-The LEDs turn off: XTR B in standby.
3. Release the button.
To interrupt the deletion procedure, release the
button before the BEEP in step 2. The LEDs turn
off: XTR B standby.
Note: If the XTR B signals an error at stage 1 and
then the LEDs turn off, carry out the total deletion
procedure.

XTR B 10 532109 - Rev.A
6. TROUBLESHOOTING
Indication Explanation Necessary action
TheLEDs donotlightup when
it is switched on. No power or the XTR B is not working. Check that the power supply is connected
and live. If there are no errors, replace
the XTR B.
When switched on, the LEDs
flash continuously. Connection error. Check the connection.
When switched on, the XTR B
gives an error. Corrupted data in memory. Carry out the Total Deletion and the First storage procedure.
WhenaTagisbroughtcloseto
the XTR B it does not activate
the command.
No power or the XTR B is not
working.
TheTag is not enabled.
Check that the power supply is connected
and live. If there are no errors, carry out
the AddTag procedure.
An enabledTag brought up to
the XTR B does not activate
the command, the LEDs flash
continuously.
Dip-switch configuration
error. Check the configurationof the dip-switches for all BUS 2easy control devices that are
connected in order to eliminate BUS 2easy
address conflicts.
New XTR B connected to the BUS 2easy board.
1. Press and release the button once.
-After 2 s, the XTR B will BEEP once and flash
once. Then it will flash for 20 s.
2. Press and release the button.
-The XTR B will BEEP once and the frequency of
the flashes will increase.
3. Within10 s,bringup a MasterTagalreadystored
on the previous XTR B.
-The XTR B will BEEP once and the LEDs will
come on for 2 s.
4. Press the button to finish. The LEDs turn off:
XTR B in standby.
7. REPLACING THE XTR B
Inthe event of replacement,youcan avoid having to repeat the storageprocedure for all previouslyenabled
Tags. A MasterTag that was stored on the previous XTR B is required.
New XTR B connected to the BUS-RELAY interface
1. Select the group: press the button the same
number of times as the number of the Group
(eg.: Group 3, press 3 times).
-After 2 s, the XTR B will BEEP and flash the
same number of times as the number of the
Group. Then it will flash for 20 s.
2. Press and release the button.
-The XTR B will BEEP once and the frequency of
the flashes will increase.
3. Within10 s,bringup a MasterTagalreadystored
on the previous XTR B.
-The XTR B will BEEP and flash the same number
oftimesasthenumberoftheGroupandtheLEDs
will come on for 2 s, then flashing resumes.
4. Press the button to finish. The LEDs turn off:
XTR B in standby.
Repeat for allTag Groups present.

XTR B 11 532109 - Rev.A
1+, ...2 s 2()


1
...~ 2 s


2

2

...
1
...
1
1
8. USAGE
1CH MODE:1 COMMAND
1. Bring theTag up to the reader in standby:
-The XTR B will BEEP once and the LEDs will come
on steadily
2. Givean impulseormaintainedaction command.
A.Impulse command: move the Tag away im-
Maintained action command in Single channel mode
Impulse command 2
...2 s MAX
...2 s MAX
Impulse command in Single channel mode
Impulse command 1
mediately.
B.Maintained action command: move the Tag
awayonly when youwish to stop the command.
When theTag is moved away, the LEDs turn off.
Impulse command 2
1. Bring the Tag close to the reader in standby and
hold it there.
-The XTR B will BEEP once; the LEDs come on
steadily.
-after 2 s, the XTR B will BEEP twice and flash
twice.
2. Move theTag away within 2 s .
-The command is activated; the LEDs turn off.
2CH MODE:2 COMMANDS
Impulse command 1
1. Bring theTag up to the reader in standby:
-TheXTRBwillBEEPonce;theLEDscomeonstead-
ily.
2. Move theTag away within 2 s .
-The command is activated; the LEDs turn off.
 Command2
STOP
1 +Command , 1 +Maintainedaction command , 
1+ Command1 , 

XTR B 12 532109 - Rev.A
3...
2


2

...

1 +,
2 s , 2 () ,
2 s , 3 () , 
1
...~6 s
1
...~9 s
 
...
Maintained action command 1 Maintained action command 2
Maintained action command 1
1. Bring the Tag close to the reader in standby and
hold it there:
-The XTR B will BEEP once and the LEDs will
come on steadily
-after 2 s, the XTR B will BEEP twice and flash
twice.
-after 2 s, the XTR B will BEEP 3 times and flash 3
times, then the LEDs will come on steadily
-after 3 s, the maintained action command is
activated
2. Move the Tag away when you wish to stop the
command, the LEDs turn off.
1 , Maintained action command 2
Maintained action command 2
1. Bring the Tag close to the reader in standby and
hold it there:
-The XTR B will BEEP once and the LEDs will
come on steadily
-after2 s,theXTR B will BEEPtwice andflashtwice
-after 2 s, the XTR B will BEEP 3 times and flash 3
times, then the LEDs will come on steadily
2. Move the Tag away within 2 s and bring it back
to the reader within 5 s:
-TheXTRB flashes once and the maintainedaction
command is activated
3. Move the Tag away when you wish to stop the
command, the LEDs turn off.
STOP
1 +,
2 s , 2 () ,
2 s , 3 () , ,
3 s Maintained action command 1
STOP
2 s MAX 5 s MAX