Bosch ARD-FPBEW2-IC User manual

FPBE W2 Fingerprint Reader
ARD-FPBEW2-IC
en Installation Guide

FPBE W2 Fingerprint Reader Table of contents | en 3
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Table of contents
1Safety 4
2Introduction 6
2.1 Components 6
2.2 Names and function of parts 8
2.3 Cables and Connectors 10
2.4 How to enroll a fingerprint 13
3Installation 16
3.1 Fixing the bracket and the product 16
3.2 Power supply connection 20
3.3 Network connection - TCP/IP 21
3.4 Wiegand Connection 22
3.5 RS 485 Connection 23
3.6 Resetting Network Settings 24
4Technical Data 25
4.1 Product Specifications 25
4.2 Dimensions 28

4en | Safety FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
1Safety
Observe the following instructions to use the product safely and
prevent any risk of injury or property damage.
!
Warning!
Risk of fire or electric shock
Do not install the product in a place with direct sunlight,
moisture, dust, or soot.
Do not install the product in a place with heat from an
electric heater.
Install the product in a dry place.
Install the product in a place with no electromagnetic
interference.
Do not install or repair the product independently.
Do not allow liquids such as water, beverages, or chemicals
get into the product.
!
Warning!
Risk of explosion
Replacing the RTC battery with an incorrect type of battery
may cause explosion. Discard the battery according to the
appropriate regional or international waste regulations.
Notice!
If the product has been damaged due to independent
installation or repair of the product by the user, free A/S
service will not be provided.

FPBE W2 Fingerprint Reader Safety | en 5
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
!
Caution!
Product damage or physical injury
Do not install the power supply cable in a place where
people pass by.
Notice!
Risk of product damage or malfunction
Do not install the product near a highly magnetic object
such as a magnet, TV, (especially CRT) monitor, or speaker.
If installing the product outside where the product is
completely exposed, install the product together with the
enclosure.
When installing a number of devices, allow a space between
the devices for installation.
Do not drop the product or apply an impact to the product.
Do not to contaminate or damage the fingerprint contact
unit with a dirty hand or foreign substances.
When cleaning the product, wipe the product with a soft
and dry cloth and no water, benzene or alcohol.
Notice!
For further information on this product
download the Installation Manual and
firmware at our website:
http://www.boschsecurity.com.
Go to Products > Access Control Systems > Readers and
Cards > Biometric readers.

6en | Introduction FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
2Introduction
2.1 Components
ARD-FPBEW2 Bracket
Ferrite Core
(1 EA)
PVC anchor
(2 EA)
Heat shrink
Star-shaped
wrench
Fixing screw (2
EA)

FPBE W2 Fingerprint Reader Introduction | en 7
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Drilling
template
OSS Manual Safety
Instructions
Quick
Installation
Guide
Notice!
Components may vary according to the installation
environment.

8en | Introduction FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
2.2 Names and function of parts
Item Feature
1 LED lamp
Indicates the operational status of the product with the color
of the LED lamp.
2 RF card authentication unit
Reads RF cards for entering and exiting.
3 Fingerprint authentication unit
Reads fingerprints placed on it for entering and exiting.

FPBE W2 Fingerprint Reader Introduction | en 9
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Item Feature
4 Network reset button
Resets the network configuration. For details, refer to the
Resetting Network Setting.
5 LED lamp for Network
Shows the status of the network connection.
6 Cable
– Interface cable
– Power cable
– Ethernet connector

10 en | Introduction FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
2.3 Cables and Connectors

FPBE W2 Fingerprint Reader Introduction | en 11
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
PIN Name Color
1 WG Tamper NO Gray (White stripe)
2 WG Tamper COM Green (White stripe)
3 WG Tamper NC Orange (White stripe)
4 Not used Blue
Brown
5 Not used Red
Green
6 WG D0 Green
7 WG D1 White
8 WG GND Black
9 TTL IN1 (LED red) Brown
10 TTL IN0 (LED green) Purple
11
PWR +VDC Red
12 Not used Pink
13 PWR GND Black (White stripe)
14 485 TRXN (RxTx-) Yellow (Black stripe)
15 485 TRXP (RxTx+) Blue (White stripe)
16 485 PAG White (Black stripe)

12 en | Introduction FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
17 ENET TXP White
18 ENET TXN Orange
19 ENET RXP Black
20 ENET RXN Yellow

FPBE W2 Fingerprint Reader Introduction | en 13
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
2.4 How to enroll a fingerprint
In order to improve the fingerprint authentication rate, register the
fingerprint correctly. ARD-FPBEW2 can recognize a fingerprint even if
the angle and position of a user's fingerprint input change. If you
register the fingerprint with attention to the following matters, the
authentication rate can be improved.
Selecting a finger for fingerprint input
– In preparation for the case that the fingerprint of a specific finger
cannot be used, for example if the user is lifting a load with one
hand or a finger gets hurt, up to 10 fingerprints for each user can
be registered.
– In the case of a user whose fingerprint cannot be recognized well,
the authentication rate can be improved by enrolling the same
finger twice repeatedly.
– If a finger has a cut or the fingerprint is blurry, select another finger
for the fingerprint.

14 en | Introduction FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
– It is recommended to use the index finger or the middle finger
when scanning the fingerprint. The authentication rate can be
reduced if it is difficult to place another finger at the center of
fingerprint sensor accurately.
Fingerprint enroll method
1. Place the finger with the fingerprint to be registered on the
fingerprint authentication unit and press the finger gently for better
authentication.
2. After a beep sounds, scan the fingerprint of the registered finger
again (scan the fingerprint of a finger to be registered twice).
Cautions for enrolling a fingerprint
When a fingerprint is recognized, it is compared with the initially
registered fingerprint, so the initial fingerprint enroll is the most
important. Pay attention to the following matters when enrolling the
fingerprint:
1. Place the finger deep enough to contact with the sensor
completely.
2. Place the center of the fingerprint in the center of the sensor.
3. If a finger has a cut or the fingerprint is blurry, select another finger
for the fingerprint.
4. Scan the fingerprint correctly without moving according to the
instruction on the screen.
5. If you make the finger upright so that the contact area with the
sensor has decreased or the angle of finger has warped, fingerprint
authentication may not be performed.

FPBE W2 Fingerprint Reader Introduction | en 15
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
When the fingerprint recognition fails
The ARD-FPBEW2 can recognize a fingerprint regardless of a change of
season or finger condition. However, the authentication rate may vary
according to the external environment or fingerprint input method.
If the fingerprint authentication cannot be done smoothly, it is
recommended to take the following measures:
1. If the finger is smeared with water or sweat, dry off the finger and
then scan the finger.
2. If the finger is too dry, blow your breath on the fingertips and then
scan the finger.
3. If the finger has a cut, register the fingerprint of another finger.
4. The initially registered fingerprint often may have not been scanned
correctly, so register the fingerprint again according to ‘Cautions for
enrolling a fingerprint’.

16 en | Installation FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
3Installation
3.1 Fixing the bracket and the product
– Determine the correct position to install the bracket using the
provided drilling template. Fix the bracket firmly using fixing screws
through the bracket to the position where ARD-FPBEW2 will be
installed.
Notice!
If installing the ARD-FPBEW2 on a concrete wall, drill holes,
insert PVC anchors, and fix them with fixing screws.

FPBE W2 Fingerprint Reader Installation | en 17
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |

18 en | Installation FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
Notice!
To avoid RF interference, a minimum separation distance
must be maintained.

FPBE W2 Fingerprint Reader Installation | en 19
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
1. Install the ARD-FPBEW2 onto the fixed bracket.
2. Connect the ARD-FPBEW2 to the bracket by rotating the star-
shaped fixing screw.
3. Fix the wall mount bracket on a wall using the wall mounting
screws.
4. Hook the FP reader on the wall mounting bracket.
5. Fix FP reader on the wall mounting bracket using the star-shaped
screw.

20 en | Installation FPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
3.2 Power supply connection
Notice!
Use a power supply adaptor of DC 12 V (± 10%) with a
minimum of 600 mA which has obtained the approval of
IEC/EN 60950-1. If you wish to connect and use another
device to the power supply adaptor, you should use an
adaptor with a current capacity which is the same or larger
than the total power consumption required for the terminal
and another device.