Faber FIC 2020S User manual

Induction Cooker
Model No FIC 2020S
Ⅰ.Specification
1). Item No.: FIC 2020S
2). Power Rate: 500W - 2000W
3). Voltage: 220V-240V / 50Hz
4). Temperature: 60℃-240℃
Ⅱ.Cautions
1). Do not plug with wet hands.
2). Do not plug into a socket where several other appliances are plugged in.
3). Do not use if the plug cord is damaged or the power plug does not fit the socket safely.
4). Do not modify the parts, or repair the unit by yourself.
5). Do not use the unit near flame or wet places.
6). Do not use where children can easily touch the unit, or allow children to use the unit by themselves.
7). Do not place on unstable surfaces.
8). Do not move the unit when the pot or the pan is on it.
9). Do not heat the pot empty or overheat the pot.
10). Do not place metallic objects such as knives, forks, spoons, lids, cans, and aluminum foils on the top
plate.
11). Use the unit with sufficient space around it. Keep the front side and either right or left side of the unit
clear.
12). Do not use the unit on carpet or tablecloth (vinyl) or any other low-heat-resistant article.
13). Do not place a sheet of paper between the pot or the pan and the unit. The paper may get burnt.
14). If the surface is cracked, switch off and take to the service center immediately.
15). Do not block air intake or exhaust vent.
16). Do not touch the top plate right after removing the pot or the pan, as the top plate will still be very hot.
17). Do not place the unit near to the objects which are affected by magnet, such as: radios, televisions,
automatic-banking cards and cassette tapes.
18). The power cord must be replaced by qualified technicians.
Ⅲ.How to Use

1). Place suitable cooking utensils in the center of the top plate and plug in, then pressing , the light
of Heating will shine, and the cooker will heat the cookware at 1400W. The power rate can be adjusted
by "+”or “-”. Please be noticed that the power range is from 500~2000W.
2). Pressing Function Selection button, Heating. Temp and Timer can be transformed circularly. The
default temperature of setting temperature in is 60℃and the default timer is 0 minutes. This
induction cooker is equipped with memory function. The power level, temperature level and timer
level interval will be stored even you change from POWER to TEMP and then back to POWER.
3). Press the "+”or “-”, the Heating can be adjusted from 500~2000W, the Temp can be adjusted from
60℃to 240℃, and the Timer can be adjusted from 0 minute to 180 minute. Be noticed that if you want
to cancel Timer, you just need to adjust to 0 during the Timer state. And if there is no operation in two
hours, the unit will be off automatically.
4). The appliance is equipped with an overheat protection. If the pot or pan is getting too hot, the
appliance will switch off power, a buzzer sounds and on the display occurs ”E2”. Should this happen,
wait for some minutes and cool the appliance down. After that, the appliance works without problems.
If meat or vegetables should the roasted, please use the temperature function to avoid any over
heating .
5). When take away the cooking pot during the working state, the induction cooker will make a sound “bi”,
then the unit will be off 1 minute later automatically.
6). Lock, press the Lock button for two seconds,it could lock the function you want, The induction cooker
has no response when press any other button during this state(except ON/OFF ), If you want to
select other function, press the Lock button for 3 seconds, every button will be work normally.
Ⅳ.Usable and Non-usable Utensils
1). Usable Pans
Steel or cast iron, enameled iron, stainless steel, flat-bottom pans / pots with diameter from 12 to 26cm.
Enameled Iron Iron or Enameled Castiron Pan Iron Pot Deep-FryPan Stainless Steel Pot Iron Plate
Pot Iron Pot
2). Non-usable Pans
Heat-resistant glass, ceramic container, copper, aluminum pans/pots. Rounded-bottom pans/pots with
bottom measuring less than 12cm.
Rounded Bottom Aluminum Bottom Measuring Pot with Stands Ceramic Pot Heat-Resistant
Pot Copper Pot Less than 12cm Glass Pot
Ⅴ.How to Clean
1). Disconnect plug and wait until the unit is cooled down completely. Clean after using every time.
2). If the pots/pans are used without being cleaned, discoloration or cooked on stains may be caused.
3). Do not use benzine, thinner, scrubbing brush or polishing powder to clean the induction cooker.
4). Wipe using dish washing agent and damp cloth.
5). Use vacuum cleaner to suck up dirt from the air intake and exhaust vent.
6). Never run water over the unit (Water gets inside may cause malfunction).
Ⅵ.TROUBLESHOOTING
Error Message
Cause
Solution
E0
No pan or unsuitable pan
Use pan or suitable pan
E1
Temperature of IGBT is too
high or the fan inside is not
working,or sencor organ is
failure.
．First Cleaking ventilation
slots if blocked.If no then let
the device cool off for a few
minutes,then try to operate
the device again .
．Contact supplier to repair
E2
Sensor is failure or the
temperature of the pan is too
high(when the pan is dry or
the unsuitable pan, the
temperatue will be very high，
the induction will cut the
power to protect the IC chip)
．Remove the cookware form
the hob. Let the device cool
off for a few minutes,then try
to operate the device again.
E3
voltage is unusual.
.Pls check the voltage
first,then try to operate the
device again.

一、 规格：
1）、型号：FIC 2020S
2）、功率调节范围：500W-2000W
3）、额定电压：220V-240V 50Hz
4）、温度调节范围：60℃-240℃
二、 注意事项：
1）、 请勿用潮湿的手插插头。
2）、 若同一插座已被几项电器同时使用，请勿把插头插入。
3）、 电线损坏或插头和插座不吻合时切勿使用。
4）、 请勿改装或自行维修。
5）、 请勿在靠近火焰或潮湿的地方使用。
6）、 请勿将电磁炉放置在儿童容易触碰到的地方，也不要让儿童单独使用电磁炉。
7）、 请勿放在不平稳的地方。
8）、 当有锅具在电磁炉上时，请勿移动电磁炉。
9）、 请勿空锅加热或过度加热。
10）、请勿将金属物体如刀叉、汤匙、瓶盖、罐子和铝箔等放在电磁炉上。
11）、 使用电磁炉时周围必须有足够空间，确保空气流通。
12）、请勿放在地毯、桌布（乙烯基），或其他不耐热的表面上使用。
13）、请勿在电磁炉和锅具之间放置纸张，以免纸张燃烧。
14）、如炉面出现裂痕，请马上停止操作，并送往服务中心。
15）、 请勿阻塞通风口或排气孔。
16）、 由于炉面使用后尚有余热，请勿立即接触。
17）、 请勿将电磁炉放置在容易受磁场影响的物体附近。如：收音机、电视、银行卡和磁带。
18）、 电源线须由专业人员更换。
三、使用方法：
1）插上电源，放置合适的锅具，按下“开/关”键，会显示功率，开机默认功率 1400W，功率可在 500W-2000W
之间调节，通过“+”“-”按键。
2）按功能选择键，可以在功率、温度、定时功能之间转换，默认温度为 60℃，默认定时为 0。
3）温度调节范围是 60℃-240℃，定时为 0-180min,开机两小时没有操作，将自动关机。
4）过温保护。锅具或炉面过热，电磁炉会发出响声，并显示“E2”，这时要停止继续加热，冷却。
5）拿开锅具时，电磁炉会“bi”的响声，一分钟后自动关机。
6）童锁、童锁键按下 2秒钟后锁紧，此时选择功能键及上下调键不能调节（开关键可开/关）。解锁、童锁键
按下 3秒钟后开锁
四、 电磁炉适用锅具
1）、适用的锅类
铸型、珐琅、不锈钢锅或壶，底部平坦，直径 12-26CM
2）、不适用的锅类
耐高温玻璃、陶瓷、铜、铝锅或壶，底部直径不超过 12CM，底部不平坦的锅或壶。
五、 清洁说明
1）、拔出插头，待表面冷却。请在每次使用后清洁电磁炉。
2）、如使用后没有及时清洁，会导致电磁炉表面褪色或留下烹煮的痕迹。
3）、请勿用石油醚、稀释剂、刷子或擦洁粉清洗电磁炉。
4）、请用洗碗液和湿布擦拭。
5）、请用吸尘器吸掉通风口和排气孔的尘埃。
6）、请勿用水冲洗电磁炉（进水可能会导致电磁炉失灵）。
6.出现的故障及解决方法
错误代码
故障原因
解决方法
E0
没有使用锅具或者使用了不适
合的锅具
放上锅具或换上适用的锅具
E1
IGBT 过热或热敏电阻损坏，风
扇不转。
1、保持进风口和出风口流
通，待机器冷却几分钟后
再重新工作。
2、联系供应商进行维修。
E2
传感器损坏或干烧保护（一般
情况下是干烧保护）
把锅具移开，待机器冷却几分
钟后再进行工作。
E3
电压出现低、高压或冲击电流
保护
检查电压，重新通电起动进行
工作。