Faber ORIZZONTE Operating and safety instructions

Faber has redefined the rangehood with
the new Orizzonte, a patented stainless
steel angled ventilation panel that hangs
on the wall behind the cooking surface.
LUXURY STYLING
stainless steel styling
artistic design, impeccable fit & finish
3 halogen bulbs with a dimmmer
hidden dishwasher-safe grease filters
Easy Cube™ Mounting System
18” mounting height for sleek cabinet design
°
°
°
°
°
°
HIGH PERFORMANCE TECHNOLOGY
Comfort-Panel™ perimetric suction system
600 cfm internal PRO™ blower model
pre-installed Silent Kit™ sound-proofing
°
°
°
STATE OF THE ART CONTROLS
push-button (LED) electronic controls on panel
4 pre-set speeds plus Intensive Power Boost
24-hour kitchen anti-pollution mode
30 minute delayed shut-down mode
grease filter saturation indicator
°
°
°
°
°
DUCTING OPTIONS
top 6 “ round venting
convertible to ductless
°
°
36 x 30 Stainless (NEW) 630006242
Includes: • Lower Chimney with holes for ducting
• Ductless Diverter Assembly • Vent Grates
• Charcoal Filter
Ductless Conversion Kit
Stainless 620000363
Replacement Charcoal Filter 620000041
High Ceiling Chimney Kit
One 40” upper chimney to replace 16
1/8” upper chimney that came with hood
Stainless 620000362
Size/Color/Model #
Orizzonte
The art of ventilation
p.o. box 435 • Wayland, MA 01778 • tel: [phone] • fax: [phone] • e-mail: [email protected] • www.faberonline.com
Designer Collection
a
c
c
e
s
s
o
r
i
e
s
NEW MODEL

Rev. 06/08
Dimensional Diagrams
Ducted Ductless
MIN. 26 3/8" - MAX. 37 3/8"
MIN. 32" - MAX. 38 1/8"
The suggested height to install the hood above the
cooktop is 18” . The Orizzonte chimneys are adjustable
and designed to meet varying ceiling heights. The
chimneys can be adjusted for ceilings between 7' 10
3/16" - 8' 9 3/16" for ducted installations and between
8’ 3 3/16” - 8’ 9 15/16” for ductless installations.
For shorter ceilings, have the chimney cover(s) cut at
a sheet metal shop. For higher ceiling installations,
the High Ceiling Chimney Kit includes a new 40”
upper chimney which would replace the 16 1/8” upper
chimney that came with the hood.
* it is highly recommended that
professional style cooking always be
vented to the outside.
Pre-Planning Your Installation - Important: Consult the installation
instructions before you begin installing this rangehood.
Ductless Installations*
For installations where ductwork is impos-
sible or highly impractical, a Ductless
Conversion Kit is available. A charcoal
filter, which attaches under the blower
assembly, absorbs smoke and odors. A
ductless diverter assembly directs the air
out to a lower chimney with vent grates cut
into the sides.
Make your ductrun as straight and short as possible. The ductrun should not
exceed 35 equivalent feet if ducted with the required minimum of 6” round
duct. Count 45º angles as 3 feet, 90º elbows as 5 feet, and 90º at elbows as
12 feet.
For best results, use no more than three 90° elbows. Make sure that
there is a minimum of 24” of straight duct between elbows if more than
one is used. Do not install two elbows together. If you must elbow right
away, do it as far away from the hood’s exhaust opening as possible.
Pre-Planning Your Installation - Important: Consult the installation instructions before you begin installing this rangehood.
WARNING! Product specifications are subject to change without notification. Consult the installation instructions before you begin installing this rangehood.