Faber TIVANO TVNO30SS395 User manual

TVNO30SS395
TVNO36SS395
Installation Instructions
Use and Care Information
Instructions d'installation
Utilisez et d'entretien
Instrucciones de instalación
Información de uso y cuidado
TIVANO

2
CONTENTS
Section Page
Important safety instructions 3
Range Hood dimensions 6
Installation height requirements 7
Parts 8
Tools needed 9
Before Installation Remove Shipping Materials 10
Only for canadian market 11
Choose Vertical or Horizontal Electrical Connection Knockout's
Choose Vertical or Horizontal Electrical Connection Knockout's 12
Ducted venting method options 14
Ducted - 7" round outlet 15
Ducted - 3 1/4" x 10" Rectangular Outlet on top 17
Ducted - 3 1/4" x 10" Rectangular Outlet rear 18
Choosing the Mounting Method 19
Mounting Range Hood on wall 20
Mounting Range Hood under the cabinet 24
Connecting electricity 26
Operating the controls 27
&DULQJIRU´OWHUV 28
Replacing lighting 29
Wiring diagram 30
Warranty 31

3
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START
INSTALLING THIS RANGE HOOD
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils slowly on low or medium setting.
E$OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQµDPEHLQJIRRGLH&UHSHV
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or
´OWHU
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
D6027+(5)/$0(6ZLWKDFORVH´WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKH
EXUQHU%(&$5()8/7235(9(17%8516,IWKHµDPHVGRQRWJRRXWLPPHGLDWHO\
EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will
result.
d) Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate
it.
 7KH´UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG
 7KH´UHGHSDUWPHQWLVEHLQJFDOOHG
 <RXFDQ´JKWWKH´UHZLWK\RXUEDFNWRDQH[LW
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with
any solid-state speed control device.
WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,
OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have any questions,
contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explo-
sive Materials and Vapors.
WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,
OBSERVE THE FOLLOWING:
1. ,QVWDOODWLRQ:RUN$QG(OHFWULFDO:LULQJ0XVW%H'RQH%\4XDOL´HG3HUVRQV,Q$FFRU-
dance With All Applicable Codes And Standards, Including Fire-Rated Construction.
2. 6XI´FLHQWDLULVQHHGHGIRUSURSHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKH
µXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQWEDFNGUDIWLQJ)ROORZWKHKHDWLQJ
equipment manufacturer's guideline and safety standards such as those published by
WKH1DWLRQDO)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ
5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQGWKHORFDOFRGHDXWKRULWLHV

4
ALL WALL AND FLOOR OPENINGS WHERE THE RANGE HOOD IS INSTALLED
MUST BE SEALED.
This Range Hood requires at least 24" of clearance between the bottom of the Range
Hood and the cooking surface or countertop. This hood has been approved by UL at this
distance from the cooktop.
This minimum clearance may be higher depending on local building codes. For gas cooktops
and combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking
surface or countertop. Consult the cooktop or range installation instructions given by the
manufacturer before making any cutouts.
MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the
Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See
Electrical Requirements"
• Venting system MUST terminate outside the home.
• DO NOT terminate the ductwork in an attic or other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOTREVWUXFWWKHµRZRIFRPEXVWLRQDQGYHQWLODWLRQDLU
)DLOXUHWRIROORZYHQWLQJUHTXLUHPHQWVPD\UHVXOWLQD´UH
WARNING
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either
through the wall or the roof.
The length of the ductwork and the number of elbows should be kept to a minimum to
SURYLGHHI´FLHQWSHUIRUPDQFH7KHVL]HRIWKHGXFWZRUNVKRXOGEHXQLIRUP'RQRWLQVWDOO
two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking
WRVHDOH[WHULRUZDOORUµRRURSHQLQJDURXQGWKHFDS
Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air
turbulence that greatly reduces performance.
0DNHVXUHWKHUHLVSURSHUFOHDUDQFHZLWKLQWKHZDOORUµRRUIRUH[KDXVWGXFWEHIRUHPDNLQJ
cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut,
then a supporting frame must be constructed.
WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.
&$87,217RUHGXFHULVNRI´UHDQGWRSURSHUO\H[KDXVWDLUEHVXUHWRGXFWDLURXWVLGH
– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces,
or garages.
Cold Weather installations
$QDGGLWLRQDOEDFNGUDIWGDPSHUVKRXOGEHLQVWDOOHGWRPLQLPL]HEDFNZDUGFROGDLUµRZDQGDQRQPH-
tallic thermal break should be installed to minimize conduction of outside temperatures as part of the
vent system. The damper should be on the cold air side of the thermal break. The break should be as
close as possible to where the vent system enters the heated portion of the house.
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
4. Ducted fans must always be vented to the outdoors.

5
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit.
A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local
FRGHVLQDFFRUGDQFHZLWKWKHHOHFWULFDOUDWLQJRIWKLVXQLWDVVSHFL´HGRQWKHVHULDOUDWLQJ
SODWHORFDWHGLQVLGHWKHXQLWQHDUWKH´HOGZLULQJFRPSDUWPHQW
ELECTRICAL INSTALLATION WITH WIRING BOX
THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform
WRWKHUHTXLUHPHQWVRIWKH1DWLRQDO(OHFWULFDO&RGH$16,1)3$ODWHVWHGLWLRQDQGDOO
local codes and ordinances. Wire size and connections must conform with the rating of
the appliance. Copies of the standard listed above may be obtained from:
National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
This appliance should be connected directly to the fused disconnect (or circuit breaker)
WKURXJKµH[LEOHDUPRUHGRUQRQPHWDOOLFVKHDWKHGFRSSHUFDEOH$OORZVRPHVODFNLQ
the cable so the appliance can be moved if servicing is ever necessary. A UL Listed,
FRQGXLWFRQQHFWRUPXVWEHSURYLGHGDWHDFKHQGRIWKHSRZHUVXSSO\FDEOHDW
the appliance and at the junction box).
:KHQPDNLQJWKHHOHFWULFDOFRQQHFWLRQFXWDKROHLQWKHZDOO$KROHFXWWKURXJK
wood must be sanded until smooth. A hole through metal must have a grommet.
• Electrical ground is required on this Range Hood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other
materials, DO NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral
or grounding circuit could result in electrical shock.
&KHFNZLWKDTXDOL´HGHOHFWULFLDQLI\RXDUHLQGRXEWDVWRZKHWKHUWKH5DQJH
Hood is properly grounded.
)DLOXUHWRIROORZHOHFWULFDOUHTXLUHPHQWVPD\UHVXOWLQD´UH
WARNING

6
RANGE HOOD DIMENSIONS
RECTANGULAR OUTLET AIR

7
MIN. 24" OVER ELECTRIC / MIN. 30" OVER GAS
CIRCULAR OUTLET AIR
Min.24” Min.30”
INSTALLATION HEIGHT REQUIREMENTS

8
PARTS
REF. PART
AHood body – Includes Controls, Light, Filters, Blower 1
BDamper ([)1
C7" Round Flange 1
DGrid (Only for Canadian Market) 1
REF PART
E3R]L6FUHZV[  4
F7RU[6FUHZV[ 4
PARTS INCLUDED
C
B
A
D

9
PARTS NEEDED
3$576FRQW
PART
7" Round Metal Ductwork
[5HFWDQJXODU'XFWZRUN
7" Damper
Wire connectors.
Power Supply Cable.
-
Drywall plugs or other suitable wall fasteners based on
your installation.
:DOO&DS5RRI&DS1HHGVWREHSXUFKDVHGVHSDUDWHO\
TOOLS NEEDED
TOOL
Tape Measure
Pencil
(OHFWULF'ULOOZLWK'ULOO%LW
Phillips Screwdriver
Torx Screwdriver
Pozi Screwdriver

10
ONLY FOR CANADIAN MARKET
1
2
For ducted installations only:
5HPRYHWKH´OWHUVRQHDWDWLPHE\SXVKLQJWRZDUGVWKHEDFNRIWKHKRRGDQG
pulling down at the same time.
Install the screws as pictured.
Install Grid Dwith the two screws removed from step 2. Screw the protection
grid into the location shown in the picture below. (The correct location has a
rectangular cut out to accommodate the grid.)
7DNHFDUHWRVFUHZWKHJULGFRPSOHWHO\µXVKWRDYRLGXQZDQWHGQRLVH
Remove the screws as pictured.
Remove two of the screws from the motor assembly housing as pictured.
3
Phillips Screwdriver
D

11
5HPRYHWKH´OWHUVRQHDW
a time by pushing them
towards the back of the
hood and pulling down at
the same time.
Remove the wiring box
cover by unscrewing
the 2 screws.
Preparing the hood for electrical knockouts
7" 1/2
13/16"
13/16"
CHOOSE VERTICAL OR HORIZONTAL
ELECTRICAL CONNECTION KNOCKOUT'S
1
2
Phillips Screwdriver

12
5HDU+ROH+RUL]RQWDO
Choose the rear hole for the electric connection and break with a screwdriver or other
tool.
During the installation thread Power Supply Cable through this hole.
3
7RS+ROH9HUWLFDO
Choose the top hole for the electric connection and break with a screwdriver or
other tool.
During the installation thread Power Supply Cable through this hole.
4

13
DUCTED VENTING METHOD OPTIONS
DUCTED WITH 7" ROUND OUTLET:
– Vertical
– Horizontal
DUCTED WITH 3 1/4" X 10" RECTANGULAR OUTLET
– Vertical
– Horizontal
7"
Rear
Top
10"
3 1/4"
10"
3 1/4"
Rear
Top
Go to page 14
Go to page 16
NON DUCTED - RECIRCULATION OPTION
Requires purchase of
Activated Charcoal
Accessory
Go to page 18

14
DUCTED - 7" ROUND OUTLET
Cut where indicated.
Remove both the rectangular and semicircle areas with metal shears.
Rear
Top
7"
Required; 7" Round
Damper purchase
separately.
1
Caution: If an elbow
is required, do it
as far away from
the hood's exhaust
opening as possible.

15
Install the Flange with Flange transition screws F.
Install 7" Round Damper purchased separately. Secure damper with foil duct tape.
Connect the 7" Round Metal Ductwork to the Roof or Wall Cap purchased separately
and then attach ductwork.
Go to page 19
2
3
Torx Screwdriver
NOTE: The Flange must be mounted with the lip facing upward.
2QO\XVHWKHVFUHZVSURYLGHGIRUWKHµDQJH
F7RU[6FUHZV[
4

16
Choose the rectangular upper air outlet or rectangular rear air outlet and cut where
indicated.(See page 18 for Rear Outlet)
Install the included rectangular air outlet with two screws F.
Connect the metal ductwork to the Roof or Wall Cap purchased separately and
then attach ductwork.
Rear
Top
Top
3 1/4 " x 10"
DUCTED - 3 1/4" X 10" RECTANGULAR OUTLET
ON TOP
1
2
3
Torx Screwdriver
F7RU[6FUHZV[
Caution: If an elbow is required,
do it as far away from the
hood's exhaust opening as
possible.

17
Go to page 19
Rear
Rear
3 1/4" x 10"
Use the rear air outlet and cut where indicated.
Install the included rectangular air outlet with two screws F.
1
2
Torx Screwdriver
F7RU[6FUHZV[
DUCTED - 3 1/4" X 10" RECTANGULAR OUTLET
REAR
Caution: If an elbow is required,
do it as far away from the
hood's exhaust opening as
possible.
Connect the metal ductwork to the Roof or Wall Cap purchased separately and
then attach ductwork.
3

18
b1
a
b2
Remove the indicated blower cover (do not discard the screw).
Reinstall the modified blower cover
with the same screw.
Cut the
cover where
indicated in
picture b1.
Discard /
Recycle
upper pieces
of blower
cover.
Install the Activated Charcoal Filter purchased separately.where indicated in the picture "C".
c
NON DUCTED RECIRCULATION OPTION
1
2
3
Required Activated Charcoal
Filter Accessory - (FILTER5)
purchased separately.
Go to page 19

19
CHOOSING THE MOUNTING METHOD
Installation for Mounting on the Wall
Installation for Mounting to the cabinet
Page
20
Page
24

20
DRAW POSITIONING LINES
Draw a vertical line Hfrom the supporting back wall to the ceiling or upper limit, at
the center of the area in which the hood will be installed.
Draw a horizontal line Ifrom where the bottom edge of hood will be located, to
a minimum of 24" above an electric cooking surface and 30" above a gas cooking
surface.
1
MIN. 24" OVER ELECTRIC/MIN. 30" OVER GAS
I
H
MOUNTING RANGE HOOD ON WALL
==
Min. 24" Min.30"