Fabit 44080 User manual

- 1 -
http://www.fabit.cn
INTRODUCTION
Thank you for purchasing a Fabit 44080 Oil Evacuation Unit.
The Fabit Oil evacuation Unit is suitable for the collection
and removal of waste oils only.
IMPORTANT INFORMATION
The information contained will help ensure many years of
dependable performance and trouble free operation.
Please take a few moments to read through this instruction
manual before operating your new 44080 Oil Evacuation
unit.
READ THIS INFORMATION
CAREFULLY BEFORE USE
Please retain this instruction manual for future reference.
Your safety is important to us. Please read and follow all
instructions listed below. Some of these instructions alert
you to the potential for personal injury. “Cautions”
throughout the manual advise of potential practices or
procedures which may cause damage to your equipment.
Make sure all operators have access to adequate
instructions about safe operating and maintenance
procedures.
Do not exceed the maximum oil temperature of 120℃.
WARNING
Before attempting any repairs or maintenance of this product,
disconnect the air supply to release the air pressure.
Do not extract caustic or flamable products.
Do not modify any component of this equipment
ASSEMBLY PROCEDURE
1．Connect the wheels to the axle, tighten the
screws. Insert the castors into the holes provided
and tighten securely.
2．Insert the handle to the handle location tubes
and tighten the screws securely.
3．Insert the gravity drain tube into the top hole on
the container and tighten.
4．Attach the oil collecting pan to the top of the
tube and tighten securely.
5．Insert the plastic strainer into the oil pan and fit
the oil pan extender.
6．Attach the vacuum generator to the remaining
hole on top of the container and tighten securely.
WASTE OIL EVACUATION SYSTEM 44080

- 2 -
http://www.fabit.cn
7．Insert the suction probe tube holder with cover into the
holder bracket on the side of the contain- er, then insert
probes into holder.
8．Attach the tool holder onto the brackets located on the
top of the container
OPERATION
Check the safety relief valve on the holding tank weekly for
correct operation. The Safety valve should open at 1.5bar
(21psi)
GRAVITY DRAIN USE
1. Open the ball valve located under the gravity drain.
2. Close the discharge ball valve located at the bottom of
the holding tank.
3. Position the gravity bowl under the sump plug. Remove
sump plug and drain the waste oil into the funnel.
OIL REMOVAL USING SUCTION PROBES
NOTE: The oil should always be removed if the oil
temperature reaches 120℃.
1．With the engine still warm, remove the dipstick from the
motor and insert the largest possible probe as far down as it
will go.
2．Connect the suction hose to the probe.
3．Close the ball valve located under the gravity bowl
4．Close the discharge ball valve located at the bottom of
the holding tank.
5．Connect the air supply to the vacuum generator
6．Open the ball valve on the suction hose, keeping the
probe dipped in the oil. The oil will be sucked from the
sump into the oil container.
EMPTY HOLDING TANK
The pressure relief valve is designed to open if the
pressure in the holding tank exceeds 21psi. If the
relief valve does not open, the valve is damaged and
should be replaced.
1．Remove the air supply from the air inlet .
2．Close the ball valve located just below the gravity
drain bowl.
3．Ensure that the ball valve on the bottom of the
holding tank is closed.
4．Place the drain hose into a bulk waste oil tank.
5．Connect air to the air inlet on the holding tank to
a pressure of 14psi (1bar) If the air Pressure
exceeds 21psi, the relief valve will open and will not
close until a pressure of 21 psi or lower is reached.
6．Open the ball valve located on the bottom of the
holding tank.
7．Note: The air will now push the waste oil out of
the holding tank into the bulk waste oil tank. If you
run out of air pressure repeat step 5.
8．After the oil transfer has been completed, re-
lease the air pressure in the holding tank and shut
the holding tank ball valve.
INSTRUCTION MANUAL
WASTE OIL EVACUATION SYSTEM 44080

- 3 -
http://www.fabit.cn
TROUBLE
CAUSE
REMEDY
1) No oil suction
a) Damaged Venture
b) Damaged Suction Probe
c) Air Leak
a) Replace Venturi
b) Replace damaged Suction Probe O’ring
c) Find and repair air leak
2) Slow draining
a) Insufficient vacuum
b) Air Leak
a) Do not use until correct vacuum pressure is achieved
b) Find and repair air leak
INSTRUCTION MANUAL
WASTE OIL EVACUATION SYSTEM 44080
TROUBLESHOOTING

- 4 -
http://www.fabit.cn
Tank Capacity
70L
Max Drainer Capacity
70L
Drainer Oil Speed Capacity
1.8-3 L/min
Oil Draining Pressure
1 bar
Max height (without extender bowl)
1.61m
Min height (without extender bowl)
1.07m
Working pressure
6-8bar (87 -116 psi)
INSTRUCTION MANUAL
WASTE OIL EVACUATION SYSTEM 44080
SPECIFICATIONS