F&V F1 User manual

C
User Guide
Safety tips
To prevent damage to your F&V product or injury to yourself or to others. Please read
the following safety precautions in their entirety before using this equipment. Keep
these safety instructions where all those who use the product will read them.
printed in japan

Screen size 7.0 inch(Diagonal)
Display area 154.08(W)×85.92(H)mm
Aspect Ratio 16:9/4:3 Selectable
Pixels 800×3(RGB)×480
Color Depth
/î5î7î%&5
Brightness 250cd/
Contrast ratio 500:1
Dot Pitch 0.0642(W)×0.1790(H) mm
24-bit(16,777,216 Colors)
Viewing angle
-1- -2-
Keep dry. Failure to observe this precaution could result in fire or electric shock.
Dust on or near the metal parts of the plug should be removed with a dry cloth.
Continued use could result in fire.
Do not handle the power cable or near the charger during thunderstorms. Failure
to observe this precaution could result in electric shock.
Do not damage, modify,or forcibly tug or bend the power cable. Do not place it
under heavy objects or expose it to heat or flame. Should the insulation be
damaged and the wires become exposed. Take the power cable to a F&V service
representative for inspection. Failure to observe this precaution could result in fire
or electric shock.
Do not handle the plug or charger with wet hands, Failuer to observe this
precaution could result in electric shock.
Use dry soft cloth to clean photographic light.You can clean with a cloth slighty
some neutral detergent to remove stubborn dirt and then with a soft cloth to dry.
Do not use strong cleaning agents, such as thinner, gasoline or alcohol, as these
solvents may damage the surface of the protective layer
:DUQLQJ
Use only batteries approved for use in this equipment.
Do not short or disassemble the battery.
Be sure the product power is off before replacing the battery.
Do not expose the battery to flame or to excessive heat.
Do not immerse in or expose to water.
Observe(Optional) proper precautions when handling batteries
Batteries may leak or explode if improperly handled.Observe the following
precautions when handling batteries for use in this product.
Observe proper precautions when handling the battery charger
Notes
Notes on the clean
Design and specifications subject to change without notice.
Specifications
Trademark Information
This mark indicates warning, before operating the unit.
Please read this manual thoroughly ,and retain it for future reference.
1. Do not let any solid object or liquid fall onto or into this equipment, to prevent
fire or shock hazard.
2. Please avoid heavy impact on the screen.
3. Please use the adapter attached in the accessory.
4. Do not expose this product to direct sunlight when monitor is working, to keep
long life and quality of the screen.
5. Never block the ventilation grille by covering it as that may damage monitor.
6. Any smoke or unusual smell coming from the equipment, please cut off and
take it to service center.
7. Please be noticed that it hasn’t inner adjust modules. Do not attempt to modify
or fix this unit. Contact qualified service personnel when any service is needed.
This equipment should never be opened for any reasons by no-professional.
8. Do not leave the equipment on while it is resting on or against something ;it
may cause a fire or damage the equipment.
9. Do not expose equipment to direct sunlight, heat or humid conditions.
10. Avoid placing the equipment near combustible or volatile solvents such as
alcohol or benzine.
11. Keep out of reach of children. Failure to observe this precaution could result in
injury.
HDMI,High-definition Multimedia Interface aretrademarks or
registered trademarks of HDMI Licensing LLC.

3
4
3
2
2
1
1
5
7
8
9
15
16
18
19
17
11
10
12
14
6
13
AV1 IN AV1 OUT
AV2 OUT
AUDIO OUT
AV2 IN
SDI IN SDI OUT
AUDIO IN
LCD monitor
6-949773-390342
6-949773-390342
Power Consumption:
0.5Amp(Max)@12V DC (6W Max)
Audio Power:1W Max
Operating Temperature:
-20 đto 70 đ
-30 đto 80 đ
Storage Temperature:
480i/p, 576i/p, 720i/p, 1080i/p
Video Input/Output:
Supports NTSC/PAL
6 949773 390342
DC 5.8~16.8V
20
Power ON/OFF
AV1/AV2/HDMI switch
Down-keyφsubject selection key,or to adjust the Contrast directly
Up-keyφsubject selection key,or to adjust the brightness directly
To activate OSD menu or select
Color/B&W switchχExit key on the set menu
16φ9/4φ3 switch
5
6
7
8
9
10
11
12
13
14
Audio output
1/4-20 female
AV1 input jack
AV1 output jack
AV2 input jack
AV2 output jack
Audio input jack
Audio output jack
SDI input jack
SDI output jack
Screen Key areas 41/4-20 female
Key areas
Infrared ray receiving window
15
16
17
18
19
20
3.5mm SYNC jack
ĭ'&LQSXW
HDMI input jack
Top lock knob
Lock knob
Shoe Head
-3- -4-
Parts diagram
F1

Connect relevant signals together and connect to power,then the unit will be in a
standby state(the red light for power is on).Press button,the red light will turn off,
which means the unit is go into working condition. If press the button again,this
unit change to standby state.State in the boot no signal input, the red power light
blinks,the screen appears "No Signal"message, if the menu "function " is set to open
in the blue screen, then a blue screen.
Operating Instructions
Remote controllerφ
Power ON/OFF
AV1/AV2/HDMI switch
Subject selection key,or to adjust the Contrast directly
Subject selection key,or to adjust the brightness directly
To activate OSD menu or select
Color/B&W switchχExit key on the set menu
Menu Operationφ
Press button ,you can enter relevant OSD menu operationθpress / on
the unit or on the remote controller to select the items:Color,Adjust,ODS,Function,
Sound,and confirm by pressing button.
Sound
1ȽColorφ
Press button to enter the menu, press the button again to confirm the
selection current Color mode, press the up or down compared with the option to
change the current mode, press the MENU button to confirm the current option,
press the up or down key was to change The current option settings.
Brightnessφ0—100
Contrastφ0—100
Saturationφ0—100
sharpnessφ0—100
Color Tempφ9300KȽ6500Ƚ3200K
Main menu
Icon
Submenu
Signal data
Color
Adjust
ODS
Function
Menu interface
-5- -6-

-7- -8-
2ȽOSDφ
Languageφㆶ։ѣᮽ/English
H Positionφ0—100
V Positionφ0—100
OSD TimeoutφOFFθ5—60 Seconds
TransparentφOFFθ1—7
3ȽFunctionφ
Reset
Display Ratioφ16φ9/4φ3/Auto
Blue ScreenφON/OFF
Flip HorizontalφON/OFF
Flip VerticalφON/OFF
Press button to enter the menu, press the button again to confirm the
selection current OSD, press the up or down compared with the option to change
the current mode, press the MENU button to confirm the current option, press
the up or down key was to change The current option settings.
Press button to enter the menu, press the button again to confirm the
selection current Function, press the up or down compared with the option to change
the current mode, press the MENU button to confirm the current option, press the up
or down key was to change The current option settings.

-9- -10-
Trouble shooting
1.Only display black and white image
AȽPls make sure that the color level settings of saturation brightness and contrast
is proper.
BȽMake sure the panel "COLOR" key color mode was opened.
2.No image after connected to power
Please check whether the AV /HDMI/SDI cable is tightly connected to output
jack,and make sure that you use standard power adopter to the monitor
3.Displaying distorted or abnormal color,as missing certain color
Please make sure that cables are securely connected;broken or loose cable will
send bad signals and make the above problems.
4.Remote controller can’t work
Press button to enter the menu, press the button again to confirm the
selection current Sound mode, press the up or down compared with the option to
change the current mode, press the MENU button to confirm the current option,
press the up or down key was to change The current option settings.
4ȽSoundφ
Volumeφ0—100
MuteφON/OFF
AȽPlease check the correct loading of battery
BȽPlease check whether there are weak batteries or remote signals are blocked
or interfered.