FARESPCB SPI AVR User manual

©2021 FARESPCB Corporation Page 1 of 7
FARESPCB Educational Products
SPI AVR Programmer Extension
Board
SPI AVR Programmer Extension Board

©2021 FARESPCB Corporation Page 2 of 7
SPI AVR Programmer Extension Board
General Description
SPI AVR Programmer Extension Board is an extension board for any
SPI AVR programmer enable user to burn code on any type of AVR
microcontroller in DIP package on only one ZIF socket.
Features
•Compatible with any SPI AVR programmer.
•Supports a wide range of AVR microcontroller chips such as
ATmega8, ATmega16, ATmega32, ATmega328, etc.
•No external power required.
•Over current protection that may result from chip mispositioning or
chip damaging.
•Red indicator LED for fault alarming.
•Green indicator LED for power.
•External crystal oscillator included.

©2021 FARESPCB Corporation Page 3 of 7
SPI AVR Programmer Extension Board
SPI AVR Programmer Extension Board
Target Sockets
Master Socket
ICSP Socket
Fault LED
Power LED
ZIF Socket
ZIF Lever

©2021 FARESPCB Corporation Page 4 of 7
SPI AVR Programmer Extension Board
Hardware Installation
1. Unlock the ZIF socket using the lever.
2. Insert your microcontroller into the ZIF socket and lock it.
(Note that the notch of any target microcontroller is aligned to the
first pin of the ZIF socket beside the lever)
3. Connect the master socket to the proper target socket using the 8-
pin flat cable.
4. Connect ICSP socket in SPI AVR board to the corresponding ICSP
socket in programmer board using the 6-pin flat cable.
5. Connect the programmer board to PC (note that the power LED will
be on).
0

©2021 FARESPCB Corporation Page 5 of 7
SPI AVR Programmer Extension Board
Supported Chips
Socket
number
Chip Num
1
ATmega16
ATmega32
ATmega8535
ATmega164
ATmega324
ATmega644
AT90S4434
AT90S8535
2
ATmega8
ATmega168
ATmega328
ATmega48
ATmega88
AT90S2333
AT90S4433
3
ATtiny11
ATtiny12
ATtiny13
ATtiny15
ATtiny25
ATtiny45
ATtiny85
AT90S2323
AT90S2343
4
ATtiny2313
AT90S1200
AT90S2313
5
ATtiny24
ATtiny44
ATtiny84
6
ATmega61
ATmega62
ATmega8515
AT90S8515
AT90S4414
CAUTION
•In case of overcurrent, the fault LED will be on, this may
occur in three conditions:
➢Chip mispositioning on ZIF socket.
➢Chip damaging.
➢Wrong plugging of ICSP cable.

©2021 FARESPCB Corporation Page 6 of 7
SPI AVR Programmer Extension Board
SPI AVR Programmer Extension Board with programmer

©2021 FARESPCB Corporation Page 7 of 7
SPI AVR Programmer Extension Board
Special Thanks to:
Eng. / Ahmed Ibrahim Ahmed
[e-mail]
Copyright © 2021 by FARESPCB
For our full range of products see our website at http://www.fares-pcb.com
If you have any technical questions about our products, e-mail us at
[e-mail]
FARESPCB co. (Head office)
32 El-Falaky st,
Bab El-Louq
Tahrir, Cairo
Egypt.
Tel: [phone]
Mob: [phone]
FARESPCB co. (Branch office)
4 El-Shabrawy st,
Road El-Farag,
Cairo,
Egypt.
Tel: [phone]
Mob: [phone]
FARESPCB Co reserves the right to make changes in circuit design, software and/or
specifications at any time without prior notification. For the most up-to-date information,
please visit our web site at http://www.fares-pcb.com
Information furnished by FARESPCB is believed to be accurate and reliable. However,
FARESPCB assumes no responsibility arising from the use of the specifications described.
Warrantee: FARESPCB™ warrants its products against defects in materials and
workmanship for a period of 30 days. If you discover a defect, we will, at our option,
repair or replace your product or refund your purchase price. This warrantee does not
cover products that have been physically abused or misused in any way.
Distributor:
RAM Electronics
32 El Falaky St. Bab El Louk
Tahrir, Cairo
Egypt.
Tel: [phone]
www.ram.com.eg
[e-mail]