FATEK P2043S User manual

R
1
T
hank you for purchasing FATEK HMI. Before installing or operating the unit, pleas
e
r
ead this installation guide carefully to ensure correct use.
1
. Safety Precautions
(Read these precautions before use.
)
1.1 General
Unpack and check the delivery for transportation damage. If any damage o
r
deformation is found, please notify the supplier.
The supplier is not responsible for the disassembled, altered or modifie
d
device.
Never allow fluid or any conductive particles to enter into the HMI.
Otherwise, it may damage the HMI, cause fire or malfunction.
Only qualified personnel may install the HMI, perform maintenance an
d
inspection.
The liquid crystal inside the LCD panel is a hazardous substance. If the pane
l
is damaged, avoid contact with the leaked liquid crystal. If the liquid crysta
l
spills on clothing or skin, use soap and wash off thoroughly. In case of ey
e
contact the liquid, hold the eye open, flush with plenty water and get medica
l
attention as soon as possible.
Do not touch any terminals while the power is on. Otherwise, it may caus
e
injury due to electrical shock.
Disconnect the power supply before installing the HMI, do wiring operation
,
perform maintenance or inspection. Otherwise, it may cause damage o
r
electrical shock.
1.2 Installation
The installation may be carried out by qualified personnel only.
Install the HMI according to the installation procedures.
Check the power source voltage is within the specified range and the polarit
y
is correct before connecting the HMI.
Keep signal and power supply cables away from high-voltage, large-curren
t
carrying cables.
P2043S HMI Installation Guide

Recommended Prohibited
No Connected
HMI
unit
Other
equipment
GOOD BAD
DC24V
+
-
FG
DC24V
+
-
FG
2
Caution
Please use solid wires between 22AWG and 12AWG.
Maximum 300V and rated temperature to 105°C for input
power pins.
Caution
Make sure the HMI is properly grounded to prevent electrical
shock, fire or malfunction.
HMI unit and other equipment should have the same electrical groundin
g
(reference voltage level), otherwise communication errors may occur.
HMI
unit
Other
equipment
1.3 Operation
Do not use sharp objects or excessive force to press the touch screen. This
may damage the touch screen.
 Do not use the output signal of the device as any safety function or system
emergency stop. It may result in personal injury or equipment damage if a
malfunction of the touch occurs.
1.4 Maintenance and Service
The agreed guarantee applies.
Only qualified personnel should make repairs and perform maintenance.
Disconnect the device from the power supply before carrying out cleaning or
maintenance.
Clean the front panel with a soft cloth and mild detergent.

Please use original replacement spare parts or accessories.

3
3
456
1
2
W
H
D
W 128.0 mm
H 102.0 mm
D 38.1 mm
2.
①
②
③
④
⑤
⑥
Power Indicator Light
Mounting Hole
Power Connector
COM1/COM2 DB-9
Male Connector
USB Connector
Mini USB Connector
Part Names and Dimensions

4
3. Specifications
Model
P2043S
UL 61010-1
Technical
Consideraon
Type of item tested
Control
Product Descripon
Operator Panel
Connecons to mains
supply
Permanent
Overvoltage category
II
Polluon degree
2
Means of Protecon
Class III
Environmental condions
Operating Temp. 0~50°C
Storage Temp. -20 ~ 60℃
For use in wet locaons
No
Equipment mobility
Built in
Operang condions
Continuous
Overall size
128.0 x 102.0 x 38.1 (mm)
Weight 215 (g)
Marked degree of
protecon
Front panel: IP65 / Rear Case: IP20 to IEC 60529
Type 1 to UL 50E
Equipment classificaon
Industrial, Professional, Commercial
Equipment class
Class III
Equipment type
Permanently connected, Fixed
I/O Port
Serial 1
Connector: D-Sub 9-Pin
COM1: RS-232 (TXD, RXD)
COM2: RS-422/485
Choose one for usage
Serial 2
---
LAN
---
USB USB2.0 Type-A (Host)x1
USB2.0 Type mini-B (Device)x1
Micro SD
---
Audio ---
PLC Extension ---
Terminaon
Switch
---
Power
Power Input
24VDC±20%
Consumpon
280mA@24VDC
Insulaon
50MΩat 500VDC
Environment
Relave Humidity
10%~90%@ 40°C (non-condensing)
Withstand Voltage
AC500V/20mA/1 Min. (between charger & FG terminals)
Vibraon
5 to 9Hz Half-amplitude: 3.5mm
9 to 150 Hz Constant acceleraon: 19.6m/s2 (2G)
3 direcons of X, Y, Z: 10mes (IEC61131-2 complaints)
Noise Suppression 1000Vp-p, width 1us, rising me 1ns
Grounding Resistance
Below 100Ω
Dimension
Cut-out
118.5 x 92.5 (mm)

4.
FATEK HMI x1
Hook and Screw x4
A4 Double-side Installation Guide
x1 Power Connector x1
5.
Push the HMI into the cotout until the
waterproof ring contacts the plate.

Insert a hook into each mounting hole
on the HMI, and then tighten the
screws evently with a moderate torque.

Failure to tighten the screws may
cause the HMI to fall, malfunction or
short-circuit. Excessive tightening may
cause deformation. The necessary
torque is about 0.16N∙m.
5
Unpacking the Unit
Installation Procedures

6.
Be sure to connect the ground FG
terminal to a class-3 ground (Ground
resistance should not exceed 100Ω).
Try to make the ground wire as short
as possible

7.
DB- 9
Male Connector
PIN#
COM1
[RS-232]
COM2
[RS-422]
COM2
[RS-485]
1
NC
*1
TX+
DATA+
2
RX
NC
NC
3
TX
NC
NC
4
NC
RX+
NC
5
GND
GND
GND
6
NC
TX-
DATA-
7
NC
NC
NC
8
NC
NC
NC
9
NC
RX-
NC
*1 NC: No Connection
6
DC24V
+
-
FG
Power Connection
Pin-out of COM Ports
Use 22–12 AWG (0.5–1.5 mm ) wire
for the power connections.
2

TEL
:[phone]
FAX :[phone]
E-mail
:[email protected]
[email protected]
Website :
www.fatek.com
R
AUTOMATION CORPORATION
26FL., NO. 29, SEC. 2, JUNGJENG E. RD.,
DANSHUEI DIST., NEW TAIPEI CITY 25170, TAIWAN, R.O.C
7
Last modified date:
01/03/2017