Feider Machines FLP30S User manual

ORIGINAL INSTRUCTIONS >EN
PORTABLE LED LAMP
FLP30S
USER GUIDE
CAUTION: Read the instructions before using the product.

CONTENTS
1. SAFETY INSTRUCTIONS 1
2. PRODUCT DESCRIPTION 3
3. SPECIFICATION 4
4. USE 4
5. REPLACEMENT OF PARTS AND MAINTENANCE 5
6. DISPOSAL 5
7. DECLARATION OF CONFORMITY 5
8. WARRANTY 6
9. PRODUCT FAILURE 7
10. WARRANTY EXCLUSIONS 8

1. SAFETY INSTRUCTIONS
To reduce the risk of electric shock, injury, and fire when using electrical devices, read and observe the
following basic safety instructions:
This projector has an IP54 degree of protection
Do not place objects within 0.5m of the projector screen
Replace any cracked or broken protective screen
Never stare at the LED beam of your projector
Do not use the projector near traffic lanes,or in any place where the power of the projector could cause
danger
The screen and the projector body may become slightly hot. Do not touch them and never approach
materials or products sensitive to heat
Never place your projector near swimming pools, bodies of water, or in any place accessible to children
It is forbidden to modify or transform the mechanical or electrical construction of the projector
Do not place the projector on a surface subject to vibration
The luminaire must always be used complete with its protective screen
The luminaire is not suitable for accent lighting
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced
Correct and safe use of the charger
Never grasp the power plug with wet hands
A device powered by a built-in battery or by a separate battery pack must always be recharged using the
charger specified for the battery in question
Using a charger designed for one type of battery may pose a risk of fire with another type of battery
Never leave the appliance plugged in without supervision
Disconnect the charger from the power supply when not in use
Do not use the charger when it is open
Do not disassemble the charger
Never place anything on the charger, it can cause overheating and damage the charger
Never place the charger near a heat source
Check that the mains voltage matches the indications on the device nameplate
Do not force the cord. Never carry the charger by the cord or pull on it to disconnect it. Keep the cord
away from heat, oil and sharp edges or moving parts. A damaged cord increases the risk of electric
shock
Before use, check the power cable for signs of damage
If the cable deteriorates during use, disconnect the plug from the power supply immediately
Do not use the charger if the cable is damaged or worn out . The battery charger should only be used
indoors.
The external flexible cable or cord of this charger cannot be replaced; if the cord is damaged, the
charger shall be scrapped
Correct and safe use of a lithium-ion battery device
The battery pack of this device was shipped in a low charge state. You must charge the battery pack
before using your electrical device for the first time
Only use the battery charger in its packaging, which matches the Lithium-ion battery, of your electrical
device
The lithium-ion battery can be charged at any time without reducing its life
1

Interrupting the procedure loading does not damage the battery
Do not incinerate the battery pack even if it is badly damaged or if it no longer charges. The battery pack
can explode on contact with fire.
A small leak of fluid from the battery may occur under extreme temperature or use conditions. However,
if the outer seal is cracked and the leak contacts your skin, wash the affected area promptly with soapy
water. If the liquid gets in your eyes, rinse your eyes with clean water for at least 10 minutes and seek
medical attention immediately.
Never try to open the battery pack for any reason. If the plastic housing of the battery pack shakes or
cracks and opens, stop using it immediately and do not recharge it
Do not store your device in temperatures below 15C and above 25C
Charge the device with the supplied charger only
Do not subject the device to impacts or to violent shocks
Do not open the device or modify its components - Do not expose the device to water, salt water or
humidity
Do not place the device near fireplaces or in a high temperature environment.
Do not place the device directly under sunlight or store it inside vehicles in hot weather, otherwise the
battery may generate heat, rupture or ignite. Using the device in this way may also result in a loss of
performance and shorten its life.
Always recharge the device, at temperatures between 10C and 40C. The ideal charging temperature is
between 180C and 24C. Do not recharge the device below 10C.
Protect the device against humidity. The device should not be wet or used in a humid environment
Always store the device in a dry place.
If you store the appliance without using it, store it in a room with an ambient temperature between 15 ° C
and 25 ° C, charged at 50%. If you store it for a very long time, fully charge the battery once every 6
months to avoid reducing its charging capacity.
Symbols explanation
Replace any cracked protective
screen.
Do not expose the charger or the
battery to water.
Dust-proof luminaire protected
against splashing water
Do not incinerate the battery or
charger.
Minimum distance of illuminated
objects in meters (between screen
and illuminated surface)
Ambient temperature of 40 °C
max. (only for the battery)
Class Ill luminaire
Use the battery and charger only in
closed rooms.
Read all instructions carefully before
use.
Charger protected against solid
objects greater than 12.5 mm and
without protection against liquids
Complies with applicable standards
Polarity indication: + in the center of
the socket.
Selective collection of electrical and
electronic waste.
Do not dispose of the battery, bring
it to a recycling center.
2

2. PRODUCT DESCRIPTION
Charger
socket
ON/OFF buttom
Handle
Support
LED
3

3. SPECIFICATION:
Model
FLP30S
Charger
AC100-240V 50/60Hz 0.3A
DC 8.4V-1.5A
Wattage
30W
Maximum surface area of the projector
0.0378 m²
Battery
Li-ion 7.4V d.c., 8000mAh
Charging time
3-4H
Discharging Time
3h(100%)/ 6 h (50%)
Index of protection
IP54 LED Floodlight
IP20 Charger
Dimension
210x180x45mm
Chips
LED SMD2835
Qty of the LED
60
Luminous flux
3000Lm
Effective peak intensity in candles
460 cd
Service life
≥30000 h(L70 @ 25℃)
Switching cycles
≥50,000
LED Color
6500K
Color rendering index
Ra>80
Start-up time up to 95% of full light emission
<2S
Start up time
<0.5S
Color consistency
<6.0SDCM
Beam Angle
120°
4. USE
Charging the battery:
The device has a built-in lithium-ion battery. Fully charge the battery before using the device for the first time.
To do this, remove the rubber cover from the charging connector on the side of the projector. Connect
the charger plug to the projector's charging connector and connect the charger plug to a mains power
socket, which must comply with current standards. A red indicator will light up and turn green as soon as
the battery is fully charged.
We recommend that you unplug your charger as soon as charging is complete (green indicator light on).
Remember to replace the rubber cover on the projector's charging connector as soon as charging is
complete
For optimum battery life, it is best to store the device only after charging it.
Note: When recharging for the first time or after long term storage, the battery will only accept 60%
discharge. After several charging and discharging phases, the battery will accept 100% charge.
It is recommended to recharge the battery at least once every 6 months in order to prolong the life of the
battery.
ON/OFF: The ON/OFF buttom located on the right side of lamp. The first pression on the buttom, the lamp
will be on and 100% brightness, the second pression it will be on 50% brightness, the third pression the lamp
will be off.
4

5. REPLACEMENT OF PARTS AND MAINTENANCE
This luminaire has built-in LED lamps. The lamps of this fixture cannot be changed
Maintenance and repair should only be carried out by a qualified professional or by
the after-sales service
The light source of this fixture is not replaceable, when the light source reaches the
end of its service life, the entire fixture should be replaced
6. DISPOSAL
Electrical products should not be discarded with household products. According to the European Directive
2012/19/EU on waste electrical and electronic equipment and its implementation into national
law, electrical products used must be collected separately and disposed of at collection points
provided for this purpose. Talk with your local authorities or dealer for advice on recycling.
7. DECLARATION OF CONFORMITY
The CE marking covers compliance with the Low Voltage Directive 2014/35/EU, the Electromagnetic
Compatibility Directive 2014/30/EU, the Eco-design Directive (ErP) 2009/125/EC, and the RoHS Directive
2011/65/EU and its amendment (EU) 2015/863.
5

WARRANTY
The manufacturer guarantees the product against defects in material and workmanship for a period of 2
years from the date of the original purchase. The warranty only applies if the product is for household use.
The warranty does not cover breakdowns due to normal wear and tear.
The manufacturer agrees to replace parts identifed as defective by the designated distributor. The
manufacturer does not accept responsibility for the replacement of the machine, in whole or in part , and/or
ensuing damage.
The warranty does not cover breakdowns due to:
• insufcient maintenance.
• abnormal assembly, adjustment or operations of the product.
• parts subject to normal wear and tear.
The warranty does not extend to:
• shipping and packaging costs.
• using the tool for a purpose other than that for which it was designed.
• the use and maintenance of the machine done in a manner not described in the user manual.
Due to our policy of continuous product improvement, we reserve the right to alter or change specifcations
without notice. Consequently, the product may be diferent from the information contained therein, but a
modifcation will be undertaken without notice if it is recognized as an improvement of the preceding
characteristic.
READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.
When ordering spare parts, please indicate the part number or code, you can fnd this in the spare parts list
in this manual. Keep the purchase receipt; without it, the warranty is invalid. To help you with your product,
we invite you to contact us by phone or via our website:
• +33 (0)9.70.75.30.30
• https://services.swap-europe.com/contact
You must create a "ticket" via the web platform.
• Register or create your account.
• Indicate the reference of the tool.
• Choose the subject of your request.
• Describe your problem.
• Attach these fles: invoice or sales receipt, photo
of the identifcation plate (serial number), photo
of the part you need (for example: pins on the
transformer plug which are broken).
8. WARRANTY
6

WHAT TO DO IF MY MACHINE BREAKS DOWN?
If you bought your product in a store:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
Go to the store with the complete machine and with the receipt or invoice.
If you bought your product on a website:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
c) Create a SWAP-Europe service ticket on the site: https://services.swap-europe.com When making the
request on SWAP-Europe, you must attach the invoice and the photo of the nameplate (serial number).
d) Contact the repair station to make sure it is available before dropping of the machine.
Go to the repair station with the complete machine packed, accompanied by the purchase invoice and the
station support sheet downloadable after the service request is completed on the SWAP-Europe site
For machines with engine failure from manufacturers BRIGGS & STRATTON, HONDA and RATO, please
refer to the following instructions.
Repairs will be done by approved engine manufacturers of these manufacturers, see their site:
• http://www.briggsandstratton.com/eu/fr
• http://www.honda-engines-eu.com/fr/service-network-page;jsessionid=5EE8456CF39CD572AA2AEEDFD
290CDAE
• https://www.rato-europe.com/it/service-network
Please keep your original packaging to allow for after-sales service returns or pack your machine
with a similar cardboard box of the same dimensions.
For any question concerning our after-sales service you can make a request on our website https://
services.swap-europe.com
Our hotline remains available at [phone].
9. PRODUCT FAILURE
7

THE WARRANTY DOES NOT COVER:
• Start-up and setting up of the product.
• Damage resulting from normal wear and tear of the product.
• Damage resulting from improper use of the product.
• Damage resulting from assembly or start-up not in accordance with the user manual.
• Breakdowns related to carburetion beyond 90 days and fouling of carburetors.
• Periodic and standard maintenance events.
• Actions of modifcation and dismantling that directly void the warranty.
• Products whose original authentication marking (brand, serial number) has been degraded, altered or
withdrawn.
• Replacement of consumables.
• The use of non-original parts.
• Breakage of parts following impacts or projections.
• Accessories breakdowns.
• Defects and their consequences linked to any external cause.
• Loss of components and loss due to insufcient screwing.
• Cutting components and any damage related to the loosening of parts.
• Overload or overheating.
• Poor power supply quality: faulty voltage, voltage error, etc.
• Damages resulting from the deprivation of enjoyment of the product during the time necessary for repairs
and more generally the costs related to the immobilization of the product.
• The costs of a second opinion established by a third party following an estimate by a SWAP-Europe repair
station
• The use of a product which would show a defect or a breakage which was not the subject of an immediate
report and/or repair with the services of SWAP-Europe.
• Deterioration linked to transport and storage*.
• Launchers beyond 90 days.
• Oil, petrol, grease.
• Damages related to the use of non-compliant fuels or lubricants.
* In accordance with transport legislation, damage related to transport must be declared to carriers within 48
hours maximum after observation by registered letter with acknowledgement of receipt.
This document is a supplement to your notice, a non-exhaustive list.
Attention: all orders must be checked in the presence of the delivery person. In case of refusal by the
delivery person, it you must simply refuse the delivery and notify your refusal.
Reminder: the reserves do not exclude the notifcation by registered letter with acknowledgement within 72
hours.
Information:
Thermal devices must be wintered each season (service available on the SWAP-Europe site). Batteries must
be charged before being stored.
10. WARRANTY EXCLUSIONS
8

BUILDER SAS
32, rue Aristide Bergès - ZI 31270 Cugnaux – France
Made in PRC 2021