lap 442PG User manual

• Fitting/Replacing the bulbs - 1 x MAX 60W E27 GLS
or energy saving equivalent.
• Always allow the bulb to cool before touching.
Fit the recommended bulbs. Do not exceed the
recommended wattage or use a different shape of
bulb as this may cause your light fitting to overheat.
• Some energy saving bulbs are not suitable for use
with a dimmer switch.
Fitting/replacing bulbs Instruction leaflet
Shutter Outdoor
Bollard and Post Light
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice. The packaging on this product can also be recycled.
Recycling advice
Safety information
26/05/2021
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could
damage the finish.
Plastic parts – Wipe clean with a damp cloth. Do not use
abrasive materials as these will damage the finish.
Do not clean the units with a pressure washer.
Cleaning 442PG, 948PG
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
The glass shade must be replaced if it becomes cracked or damaged.
Do not use product without glass shade attached. Replace Cracked
Shade
UK Manufacturer:
Kingfisher International Products Limited,
3 Sheldon Square, London, W2 6PX,
United Kingdom.
EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E,
1011 VM Amsterdam, The Netherlands.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
Fixing Instructions
Specification
Voltage: 240V 50Hz
Lamp: Max. 1 x 60W E27 GLS
IP rating: 44
Make sure you have the following items which
are required to install this light fitting:
• Selection of cross and flat head screwdrivers.
• Electric drill and assorted drill bits.
• Wire strippers.
• Insulation tape.
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work, and retain for reference.
Install in accordance with IEE Wiring regulations
and current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without
your knowledge. If you are in any doubt, please consult
a qualified electrician.
This light fitting should be connected to a circuit
with a 30mA RCD fitted.
When changing a bulb, always switch off at the
mains and allow the old bulb to cool before handling.
Dispose of used bulbs carefully and responsibly.
Do not exceed the wattage stated or use a different
shape bulb as indicated on the fitting. This product
is not suitable for dimming.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is rated at IP44. It is not suitable for
location in or near a marine or sea environment.
Existing fittings must be completely removed before
installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
• The product must be mounted onto a concrete base
or paving slab. It should not be directly installed
in the soil. Using base plate as a template,
mark the fixing holes onto the mounting surface.
• Drill holes to the necessary size and depth - taking
care not to damage any concealed pipes or wiring
below the mounting surface.
• This product comes complete with expanding bolt
type fixings (C) which are suitable for use on most
surfaces, however alternative fixings may be required.
• Double check that the fixings line up with the holes
in the base of the fitting Push the fixing bolts into the
mounting holes. Fit washers (B) and tighten nuts (A)
with a suitable spanner to secure.
Installation
Cable wired to product
Terminal block case EARTH
wire
EARTH
wire
NEUTRAL
wires
LIVE
wires
Supply cable
Spacing strip
Layout
• Plan the desired layout of this fitting carefully, ensuring
the cables will reach the distance between the junction
box and the light fitting.
• This product is designed for domestic and light industrial
use. It should not be used to support other objects or
used as a replacement for concrete or metal pillars.
• Avoid locating any cables in positions that would cause
a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may
be at risk from being cut, trapped or damaged.
• We recommend that you use H05RN-F specification
cable (not supplied) which is an outdoor grade, rubber
sheathed cable. The mains supply cable must have
a minimum cross sectional area of 1.0mm².
• Cables must be protected using suitable conduit or
plastic trunking.
Having correctly identified the wiring from your existing
light fitting, pull the wire through the hole and connect to the
connection block inside the product in the following way:
• Pull terminal block (D) from inside of tube.
• Unscrew the 4 screws which attach the black box to
the spacing strip. Open the black box and pull out the
terminal block.
• Connect the input wires according to the diagram.
• Push terminal block back into the black box. Re-attach
the black box to the mounting bracket.
Wiring
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the
connection block.
Check that...
• Replace the plastic cover and stainless steel plate
ensuring that the screws are securely tightened.
• Replace fuse or circuit breaker and switch on.
Your light is now ready for use.
Commissioning
A
D
B
C