Fenger FIR-433 User manual
CAUTION:
RISK OF ELECTRICAL
SHOCK DO NOT OPEN
GENERAL SAFETY SUMMARY
CAUTION:
DO NOT REMOVE THE COVER FOR REDUCING THE RISK OF ELECTRIC SHOCK.
NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
IMPORTANT SAFETY INSTRUCTIONS
1. All the safety and operating instructions should be read before the product is operated.
2. The safety and operating instructions should be retained for future reference.
3. All warnings on the product and in the operating instructions should be adhered to.
4. All operating and use instructions should be followed.
5. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for the cleaning.
6. Do not use attachments not recommended by the products manufacturer if they may
cause hazards.
7. Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool; and the like.
8. Any mounting of the product should follow the manufacturer's instructions, and should
use a mounting accessory recommended by the manufacturer.
9. This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type or power supply to your home, consult your
product dealer or local Power Company. For products intended to operate from battery
power, or other sources, refer to the operating instruction.
10. Power supply cord should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at
plugs, or other sources, refer to the operating instructions.
11. For added protection for this product during a lightning storm, or it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect cable
Users Manual
FENGER®FIR-433
Wireless IR Remote Control Extender
system.
This will prevent damage to the product due to lightning and power line surges.
12. Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electrical shock.
Never spill liquid of any kind on the product.
13. Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
14. Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions.
◎When the power- supply cord or plug is damaged.
◎If liquid have been spilled, or objects have fallen into the products
◎If the product does not operate normally by following operating instructions, adjust only
those controls that are covered by the operating instructions as an improper
adjustment of other control may result in damage and will often require extensive
work by a qualified technician to restore this product to its normal operation.
◎When the product exhibits a distinct change in performance - this indicates a need for
service.
◎If the products has been dropped or damaged in any way.
15. When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or that have the same characteristics as
the original part. Unauthorized substitutions may result in fire, electric shock, or other
hazards.
16. Upon completion of any service or repair to this product ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
17. The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products including amplifiers that produce heat.
INTRODUCTION
Application
FIR-433 Remote Control Extender system uses the latest wireless technology to send Infrared
Signal from one room to another room. With the Infrared Receiver and Infrared Transmitter, you
can control your A/V appliances or any other equipments, that has IR Remote control, around
your home.
Features & Benefits
Advanced technology for new 433 MHz Wireless IR extender
Transmit the IR remote control signal by radio frequency passing walls, floors
ASK modulation & High data rate IR Extender transmission
Universal IR carry range: 30~60 KHz
Omni-directional antenna & Compact size design
Compatible with almost any IR remote control, such as TV, Set-Top-Box, DVD, CD player
or Air Conditioner.
Specification
Item
Transmitter
Receiver
Frequency
433,92 MHz
Modulation
ASK
Range between Tx and Rx
Up to 100m free field,
up to 30m through walls and floors
Operation Current
23mA stand by
280mA operating
16mA stand by
40mA operating
Sensitivity
-90dBm
IR Data Carry
30~60 KHz
IR Range
5m
4m
IR Angle
±30° from centre
Dimensions
Ø77 x 38mm (without antenna)
Power supply
100-240 VAC 50/60Hz, 9 VDC / 660mA adaptor
PACKAGE CONTENTS
The package includes the following device. (Please check package before use.)
One unit of Transmitter
The Transmitter receives the IR signal from remote control and converts to the 433 MHz RF
signal; sending to the Receiver.
One unit of Receiver
The Receiver receives the 433 MHz RF signal from Transmitter and converts to the IR signal,
emitting to control the A/V appliances.
One unit of IR Extender Mouse
The IR Extender Mouse is plugged into the Receiver for Situations where placement in front of
the instrument is difficult.
Two units of power adaptor.
These power adaptors supply a +9V DC power to the Transmitter and the Receiver.
LOCATION OF CONTROLS
Transmitter Receiver
1. IR LED 4. Power ON/OFF
2. IR Window 5. IR Extender Mouse Connector
3. Adaptor Connector 6. Antenna
SYSTEM INSTALLATION
Install the Transmitter
Use in the room where you want to use the remote control
Plug the Transmitter into a standard electrical outlet and turn on the power.
Place the IR window of the Transmitter facing you.
The Transmitter can be placed up to 5m from where you will be using the remote
control.
Transmitter
Remote control
Room 1
Install the IR Extender Mouse
Use when the Receiver cannot be easily placed in front of the A/V appliances.
Plug the IR Extender into back of the Receiver.
Place the IR Extender mouse in front of the IR window of the A/V appliances that you
want to control.
Install the Receiver
Use in the room where A/V appliances should be controlled
Plug the Receiver into a standard electrical outlet and turn on the power.
Place the IR window of the Receiver facing the equipment that you want to control.
The Receiver can be placed up to 3-4m from where you will be using the A/V appliances.
AV Source
Room 2
Receiver
TROUBLE SHOOTING
Please read this user manual carefully before using the IR Remote Control Extender. If you still
have difficulties to use the system, consult the following instructions, which will guide you to
solve most common problems.
Make sure both Receiver and Transmitter are plugged into a standard electrical outlet.
Make sure the power adaptor and IR Extender Mouse are plugged into the connectors properly.
Check if the Remote Control is out of battery.
When the Remote Control is operated, the IR LED of the Transmitter does not flash
Make sure your Remote Control is able to align the Transmitter IR window.
Make sure nothing is blocking the path between the Remote Control and the
Transmitter.
Make sure the distance between the Remote Control and the Transmitter is within 5m.
Move to another location and try it again.
When the IR LED of the Transmitter is continuously illuminated
In a few cases, the Transmitter may be disrupted by interference and cannot, therefore,
pick up the signals it receives. If this is the case the IR LED will be continuously
illuminated and the Transmitter must be relocated. This interference is caused by
equipment in the vicinity such as dimmers, energy-saving light bulbs, IR alarms and so
on.
When the Remote Control is operated, the IR LED of the Receiver does not flash
Make sure the Transmitter is no more than 30m from the Receiver install.
Make sure the Receiver is pointed at the front of the A/V appliances that you want to
control.
Move to another location and try it again.
Make sure the distance between the Receiver and the A/V appliances that you want to control
is within 4m.
Make sure the IR extender mouse is placed in front of the IR window of the A/V appliances
that you want to control.
© 2012 FENGER Marketing | 20120623-EN-V1.0
Specifications subject to change without notice.
:
:
.
.
,
1.
.
2.
3.
4. .
5. .
6.
7. - , ,
, , .
8.
,
9.
. ,
,
.
FENGERFIR-433
IR
10.
, ,
.
11. ,
,
.
.
12.
.
.
13. ,
.
14.
:
◎
◎ .
◎
,
.
◎
.
◎
15.
.
,
16.
,
.
17. ,
,
.
FIR-433
A/V
IR, .
433 MHz
IR ,
ASK & IR
IR: 30~60 KHz
-& Compact
IR, TV, Set-Top-Box, DVD, CD
player Air Conditioner.
433,92 MHz
ASK
Tx Rx
100m ,
30m
23mA
280mA
16mA
40mA
-90dBm
IR
30~60 KHz
IR
5m
4m
IR
)
100-240 VAC 50/60Hz, 9 VDC / 660mA adaptor
. (
.)
IR RF 433
MHz
RF 433 MHz IR,
A/V.
IR Extender Mouse
IR Extender Mouse ,
.
.
+9V DC .
1. IR LED 4. ON/OFF
2. IR 5. IR Extender Mouse
3. Adaptor 6.
.
IR
5m
1
IR Extender Mouse
IR Extender Mouse
A/V.
IR Extender mouse
IR Extender mouse IR A/V
.
A/V.
IR
3 4m
A/V.
AV
2
IR. ,
,
.
IR Extender Mouse
.
.
, IR LED
IR .
.
5m.
.
IR LED
,
.
IR LED
.
, , IR .
, IR LED
30m
A/V
.
.
A/V
4m.
IR extender mouse IR
.
Marketing | 20120623-GR-V1.0
.
Table of contents
Languages:
