Festool CXS User manual

706253_002
Festool GmbH
Wertstraße 20
D-73240 Wendlingen
Tel.: [phone]
Telefax: +49 (0)7024/804-20608
www.festool.com
Originalbetriebsanleitung - Akku-Bohrschrauber 7
Original operating manual - Cordless drill 12
Notice d’utilisation d’origine - Perceuses-visseuses sans fil 17
Manual de instrucciones original - Taladro atornillador de batería 22
Istruzioni per l'uso originali - Trapano avvitatore a batteria 27
Originele gebruiksaanwijzing - Accuschroefboormachines 32
Originalbruksanvisning - Batteri-borr/skruvdragare 37
Alkuperäiset käyttöohjeet - Akkukäyttöinen porakone/ruuvinväännin 42
Original brugsanvisning - Akku bore-skruemaskine 47
Originalbruksanvisning - Batteridrevet bor-/skrumaskin 52
Manual de instruções original - Aparafusadora de acumulador 57
Оригинал Руководства по эксплуатации - Аккумуляторная дрель-шуруповёрт 62
Originál návodu k obsluze - Akušroubovák - vrtačka 68
Oryginalna instrukcja eksploatacji - Akumulatorowa wiertarko-wkrętarka 73
CXS

1
2
2
1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
2-1
1-9
1-10
1-11
1
2
1-8

;
1
1
2
klick
3-1
3
3
3A
5mm
3 mm
85 mm
(3 11/32“)
:

WH-CE
CENTROTEC®
BF-FX 10
klick
4
5
klick
klick
12
12
3
4
3

XS-AS
6
7
1
2
WH-CE
BF-FX 8
BF-FX 10

LiIon 1,5 Ah
80 % 100 %
LiIon 2,6 Ah
23
40
35
60
2,6
3
10,8
0,22
CXS, TXS
6
U
#
V~
V=
V=
Ah
C
kg
A
C
Hz
min.
min.
220 - 240
10,8
2,6
-10° - 40°
0° - 55°
II
50/60
MXC
BP-XS

12
CXS
GB
Original operating manual
1Symbols
2Safetyinstructions
2.1 General safety instructions
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future ref-
erence.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
2.2 Machine-specific safety notices for cordless
drills
– Hold power tool by insulated gripping surfaces,
when performing an operation where the cut-
ting accessory or fastener may contact hidden
wiring. Cutting accessory or fasteners contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
– Use suitable detectors to determine if utility
lines are hidden in the work area or call the lo-
cal utility company for assistance. Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pene-
trating a water line causes property damage or
may cause an electric shock.
– Wear suitable protection: such as ear protec-
tion, safety goggles, a dust mask for work which
generates dust, and protective gloves when
working with raw materials and when changing
tools.
CAUTION! Power tool can block and cause
sudden kickback! Switch off immediately!
– Do not lock the on/off switch permanently!
2.3 Battery pack and charger safety instruc-
tions
– This charger can be operated by persons with re-
duced physical, sensory or mental capabilities or
a lack of practical experience and knowledge,
provided they are supervised or have been in-
structed to use the machine safely and under-
stand the dangers of machine operation.
Children are not allowed use or play with the ma-
chine.
– Do not open the battery pack or the charger!
– Prevent metal parts (e.g. metal chips) or fluids
from entering the charger!
–
Risk of explosion! Do not use battery packs or
chargers from other manufacturers!
– Protect the battery pack from excessive heat > 50
°C or constant heat sources such as sunlight or
naked flames!
– Never use water to extinguish burning li-ion bat-
tery packs! Use sand or a fire blanket.
– Check the plug and the cable regularly and
should either become damaged, in order to avoid
Symbol Significance
Warning of general danger
Risk of electric shock
Read operating instructions and safety
notices!
Wear ear protection.
Wear protective gloves.
Wear a dust mask.
Wear protective goggles.
Do not dispose of with domestic waste.
Inserting the battery pack.
Removing the battery pack.
Tip or advice
Handling instruction
Mains voltage (input) and frequency
Voltage (output)
Rapid charging max.
Permitted temperature range
Safety class II
Charging times
Capacity
Number of cells
Weight
#

CXS
13
GB
a hazard, have them replaced by an authorised
after-sales service workshop.
– Always pull the mains plug out of the socket
when the charger is not in use.
2.4 Emission levels
Levels determined in accordance with EN 60745 are
typically:
Vibration emission value a
h
(vector sum for three
directions) and uncertainty K measured in accor-
dance with EN 60745:
The specified emissions values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary esti-
mates regarding vibration and noise loads during
operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
3 Intended use
Cordless drill suitable
– for screwing in and tightening screws,
– for drilling in metal, wood, plastics and similar
materials.
Not intended for clamping tools other than drills
and drill bits, e.g. compass saws, stirring rods,
metal brushes.
Charger MXC suitable
– for charging the listed battery packs.
– only for indoor use.
The user is liable for improper or non-in-
tended use; this also includes continuous in-
dustrial operation.
4Technicaldata
* Speed specifications with fully charged battery
pack.
 Further technical data on the charger and the
supplied battery pack can be found on page 6.
5 Machine features
The specified illustrations appear at the beginning
of the Operating Instructions.
6Operation
6.1 Changing the battery pack [2]
 Battery pack is ready for use immediately upon
delivery and can be charged at any time.
 Side of the belt clip [2-1] can be replaced when
battery pack is removed.
6.2 Charging the battery pack [3]
The LED [3-1] on the charger indicates the respec-
tive operating status of the charger.
Sound pressure level L
PA
= 65 dB(A)
Sound power level L
WA
= 76 dB(A)
Uncertainty K = 3 dB
Wear ear protection.
Fastening a
h
=4,0 m/s
2
K = 1,5 m/s
2
Drilling in metal a
h
=3,0 m/s
2
K = 1,5 m/s
2
Cordless drills CXS
Motor voltage 10,8V
Idle engine speed* 1st gear 0 - 430 rpm
2nd gear 0 - 1300 rpm
Max. torque
soft/hard screw joints 10/ 16 Nm
Adjustable torque 0,2 - 2,4 Nm
Chuck clamping range 1 - 10 mm
Drill diameter max.
Wood/Metal 12/ 8 mm
Tool holder in drill spindle 1/4 ’’
Weight without battery pack with
Centrotec 0,7 kg
[1-1] Drilling symbol
[1-2] Torque thumbwheel
[1-3] Torque/drilling position marking
[1-4] Gear switch
[1-5] Right/left switch
[1-6] On/Off switch
[1-7] Belt clip
[1-8] Insulated gripping surfaces (grey shaded
area)
[1-9] Button for releasing the battery pack
[1-10] Bit store
[1-11] LED lamp with capacity indicator
[3A] Wall mount for charger

14
CXS
GB
7 Settings
7.1 Changing direction of rotation [1-5]
• Switch to the left = clockwise rotation
• Switch to the right = counterclockwise rotation
7.2 Changing gear [1-4]
• Gear switch forwards (digit 1 visible) = 1st gear
• Gear switch to rear (digit 2 visible) = 2nd gear
7.3 Adjust torque [1-2]
The marking [1-3] shows the selected position.
Drilling
Marking shows the drill symbol [1-1] = Maximum
torque.
Fastening
Torque corresponding to setting:
Position 1 = low torque
Position 12 = high torque
8 Tool holder, attachments
The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
8.1 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CENTRO-
TEC tool chucks.
8.2 Chuck BF-FX10 [5]
For clamping drill bits and bits with max. shaft di-
ameter of 10 mm.
Clamp tool centrally in the chuck.
8.3 Elbow adapter XS-AS [6]
(accessories) Drilling and screwdriving at right an-
gle to power tool.
 You can engage the elbow adapter in 16 different
angle settings.
8.4 Tool holder in the drill spindle [7]
Bits can be inserted directly into the hexagon sock-
et holder of the drill spindle.
9 Working with the power tool
9.1 On/Off switch [1-6]
Press = ON, release = OFF
 The speed of the machine depends on how far
the on/off switch is pressed in.
LED yellow - lit continuously
Charger is ready to use.
LED green - flashing quickly
Battery pack is charged to maxi-
mum capacity.
LED green - flashing slowly
Battery pack is charged to 80%
and with reduced current.
LED green - lit continuously
Battery pack is charged.
LED red - flashing
General fault indicator, e.g.
incomplete contact, short circuit,
defective battery pack, etc.
LED red - lit continuously
Battery temperature is outside
permissible limit values (0 °C to
55 °C).
CAUTION
Risk of injury
 Always switch off the power tool before adjusting
settings!
WARNING
Risk of injury
 Always disconnect the battery pack before per-
forming any type of work on the machine!
CAUTION
Hot and sharp tools
Risk of injury
 Wear protective gloves.
WARNING
Risk of injury
 Always secure the workpiece in such a manner
that it cannot move while being machined.

CXS
15
GB
9.2 LED lamp with capacity indicator
The LED bulb [1-11] lights up when the ON/OFF
switch is pressed [1-6] .
After releasing the ON/OFF switch [1-6] the capac-
ity indicator on the LED lamp [1-11] displays the
state of charge of the battery pack for a few sec-
onds:
9.3 Bit depot [1-10]
Magnetic, for storing bits and bit holders.
9.4 Warning signals
Power tool shuts down, capacity indicator flashes:
Battery pack is empty.
 Change the battery pack.
Power tool shuts down, capacity indicator does
not flash: Power tool is overheating or has been
overloaded.
 Apply a lesser load to power tool.
 Allow power tool to cool down.
10 Service and maintenance
Customer service and repair only
through manufacturer or service
workshops: Please find the nearest
address at: www.festool.com/service
Use only original Festool spare parts!
Order No. at: www.festool.com/service
Note the following information:
– Keep the ventilation slits on the machine free and
clean to ensure adequate cooling.
– Keep the contacts on the machine, charger and
battery pack clean.
Information on battery packs
– Store in a cool, dry place at a temperature be-
tween 5 °C and 25 °C.
– Protect battery packs from moisture, water and
heat.
– Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. Danger of deep discharge!
– If you intend to store li-ion battery packs for lon-
ger periods without use, you should charge them
to 40 % capacity (approx. 15 min charging time).
– To avoid short circuits the battery pack should be
stored in the packaging supplied.
11 Environment
Do not dispose of the device in house-
hold waste! Recycle devices, accesso-
ries and packaging. Observe applica-
ble national regulations.
EU only: In accordance with European
Directive on waste electrical and electronic equip-
ment and implementation in national law, used
electric power tools must be collected separately
and handed in for environmentally friendly recy-
cling.
Return used or faulty battery packs to your local
specialist retailer, Festool after-sales service or
nearest public waste management facility (observe
applicable regulations). Batteries must be dis-
charged on return. Battery packs will then be recy-
cled.
EU only: In accordance with the European Directive
on batteries and implementation in national law,
defective or used battery packs/batteries must be
collected separately and handed in for environmen-
tally friendly recycling.
Information on REACh: www.festool.com/reach
12 Transport
The lithium-ion batteries are subject to the require-
ments of the legislation on hazardous goods. A li-
ion battery pack alone falls below the applicable
limit value and certified as per UN manual ST/SG/
AC.10/11/rev. 3 part III, subsection 38.3. However,
dangerous goods regulations may apply when sev-
eral battery packs are transported For shipping by
third parties (e.g. air transport or freight forward-
ing company) special requirements with regard to
packaging and labelling must be observed.For the
preparation of the package an expert on hazardous
goods must be consulted. Please observe any fur-
ther national regulations.
Only return the battery pack if the housing is un-
damaged. Tape over the exposed contacts and wrap
the battery pack so that it cannot move inside the
packaging.
70 - 100%
40 - 70 %
15 - 40 %
< 15 %
Recommendation:
Charge battery pack
before further use.
100%
0%
EKAT
1
235
4

16
CXS
GB
13 EU Declaration of Conformity
We declare under sole responsibility that this prod-
uct complies with all the relevant requirements in
the following Directives, standards and normative
documents:
2004/108/EC, 2006/95/EC, 2011/65/EU, EN 60745-
1, EN 60745-2-1, EN 60745-2-2, EN 55014-1, EN
55014-2.
We declare under sole responsibility that this prod-
uct complies with all the relevant requirements in
the following Directives, standards and normative
documents:
2004/108/EC, 2006/95/EC, 2011/65/EU, EN 60335-
1, EN 60335-2-29, EN 61000-3-2, EN 61000-3-3, EN
61204-3.
Festool GmbH
Wertstr. 20, D-73240 Wendlingen, Germany
Dr. Martin Zimmer
Head of Research, Development and Technical
Documentation
2014-04-16
Cordless drill Serial no.
CXS 10010708
Year of CE mark: 2014
Charger Serial no.
MXC 495883
Year of CE mark: 2010