Festool PDC 18/4 Li Installation instructions

708368_002
Festool GmbH
Wertstraße 20
D-73240 Wendlingen
Tel.: [phone]
Telefax: +49 (0)7024/804-20608
www.festool.com
Originalbetriebsanleitung - Akku-Schlagbohrschrauber 6
Original operating manual - Cordless percussion drill 10
Notice d’utilisation d’origine - Perceuse-visseuse à percussion sans fil 14
Manual de instrucciones original - Taladro atornillador de percusión de batería 19
Istruzioni per l'uso originali - Trapano avvitatore a percussione a batteria 24
Originele gebruiksaanwijzing - Accuslagboorschroefmachine 29
Originalbruksanvisning - Batterislagskruvdragare 33
Alkuperäiset käyttöohjeet - Akkuiskupora/ruuvinväännin 37
Original brugsanvisning - Akku-slagbore-/skruemaskine 41
Originalbruksanvisning - Batteridrevet slagbor-skrumaskin 45
Manual de instruções original - Aparafusadoras de percussão de acumulador 49
Оригинальное руководство по эксплуатации - Аккумуляторная ударная дрель-шуруповёрт 54
Originální návod k použití - Akumulátorový kombinovaný šroubovák 59
Oryginalna instrukcja eksploatacji - Akumulatorowa wiertarko-wkrętarka udarowa 63
PDC 18/4 Li

EG-Konformitätserklärung. Wir erklären
in alleiniger Verantwortung, dass dieses Pro-
dukt allen einschlägigen Bestimmungen der
folgenden Richtlinien einschließlich ihrer Än-
derungen entspricht und mit den folgenden
Normen übereinstimmt:
EC-Declaration of Conformity. We declare
under our sole responsibility that this product is
in conformity with all relevant provisions of the
following directives including their amend-
ments and complies with the following stan-
dards:
CE-Déclaration de conformité communau-
taire.
Nous déclarons sous notre propre respon-
sabilité que ce produit est conforme aux
normes ou documents de normalisation sui-
vants:
CE-Declaración de conformidad.
Declaramos bajo nuestra exclusiva responsabi-
lidad que este producto corresponde a las si-
guientes normas o documentos normalizados:
CE-Dichiarazione di conformità.
Dichiariamo sotto la nostra esclusiva respon-
sabilità che il presente prodotto e conforme
alle norme e ai documenti normativi seguenti:
EG-conformiteitsverklaring.
Wij verklaren op eigen verantwoordelijkheid dat
dit produkt voldoet aan de volgende normen of
normatieve documenten:
EG-konformitetsförklaring.
Vi förklarar i eget ansvar, att denna produkt
stämmer överens med följande normer och
normativa dokument:
EY-standardinmukaisuusvakuutus.
Vakuutamme yksinvastuullisina, etta tuote on
seuraavien standardien ja normatiivisten oh-
jeiden mukainen:
EF-konformitetserklæring
Vi erklærer at have alene ansvaret for, at dette
produkt er i overensstemmelse med de følgen-
de normer eller normative dokumenter:
CE-Konformitetserklæring
Vi erklærer på eget ansvar at dette produktet er
i overensstemmelse med følgende normer el-
ler normative dokumenter:
CE-Declaração de conformidade:
Declaramos, sob a nossa exclusiva responsabi-
lidade, que este produto corresponde às nor-
mas ou aos documentos normativos citados a
seguir:
Д екларация соответствия ЕС: Мы
заявляем с исключительной
ответственностью, что данный продукт
соответствует следующим нормам или
нормативным документам:
ES prohlašeni o shodě: Prohlašujeme s
veškerou odpovědnosti, že tento vyrobek je ve
shodě s nasledujicimi normami nebo
normativnimi dokumenty:
.
Oświadczenie o zgodności z normami UE:
Niniejszym oświadczamy na własną
odpowiedzialność, że produkt ten spełnia
następujące normy lub dokumenty
normatywne:
______________________________________
2006/42/EG, 2014/30/EU, 2011/65/EU
EN 60745-1, EN 60745-2-1, EN 60745-2-2,
EN 50581
______________________________________
Festool GmbH
Wertstr. 20
D-73240 Wendlingen
GERMANY
Wolfgang Zondler
Head of Research, Development and Tech-
nical Documentation
Wendlingen, 2016-06-20
Akku-Bohrschrauber
Cordless drill
Perceuses-visseuses sans fil
Serien-Nr.
Serial no.
N° de série
PDC 18/4 768172

1-1
1-2
1-3
1-4
1-5 1-6
1-7
1-8
1-9
1-10
1-11
2A
1
2B
1-12
1
2
klick
BP/C 18

4
3
klick klick
1
2
3
4
3-2
3-1

8
A
B
5
67
8-1
1
1
2
2
klick
3
4
4
5
klick
12
3
klick

10
PDC 18/4 Li
GB
Original operating manual
1Symbols
2Safetyinstructions
2.1 General safety instructions
WARNING! Read all safety warnings, in-
structions, illustrations and specifications
provided with this power tool.
Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future ref-
erence.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
2.2 Machine-specific safety notices for cordless
drills
– Wear ear protection when impact drilling. Expo-
sure to noise can result in loss of hearing.
–
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
–
Hold power tool by insulated gripping surfaces,
when performing an operation where the cut-
ting accessory or fastener may contact hidden
wiring.
Cutting accessory or fasteners contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
– Use suitable detectors to determine if utility
lines are hidden in the work area or call the lo-
cal utility company for assistance.
Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pene-
trating a water line causes property damage or
may cause an electric shock.
–
Wear suitable protection: such as ear protec-
tion, safety goggles, a dust mask for work which
generates dust, and protective gloves when
working with raw materials and when changing
tools.
CAUTION! Power tool can block and cause
sudden kickback!
Switch off immediately!
–
Hold the power tool firmly in your hand. Adjust
the torque correctly for screwing. Be prepared
for a high reaction torque,
which may cause the
power tool to turn and possibly lead to injury.
–
Do not use the power tool in the rain or in damp
surroundings.
Moisture in the power tool may
cause a short circuit and burning.
– Do not lock the on/off switch permanently!
2.3 Emission levels
Levels determined in accordance with EN 60745 are
typically:
Vibration emission value a
h
(vector sum for three
directions) and uncertainty K measured in accor-
dance with EN 60745:
Symbol Significance
Warning of general danger
Risk of electric shock
Read operating instructions and safety
notices!
Wear ear protection.
Wear protective gloves.
Wear a dust mask.
Wear protective goggles.
Do not dispose of as domestic waste.
Tip or advice
Handling instruction
Drilling
Sound pressure level L
PA
= 73 dB(A)
Noise level L
WA
= 84 dB(A)
Uncertainty K = 3 dB
Impact drilling
Sound pressure level L
PA
= 104 dB(A)
Noise level L
WA
= 115 dB(A)
Uncertainty K = 3 dB
CAUTION
When working with noise
Damage to hearing
X Always use ear protection.

PDC 18/4 Li
11
GB
The specified emission values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary esti-
mates regarding vibration and noise loads during
operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
3 Intended use
Cordless impact drills are suitable for
– drilling in metal, wood, plastic and similar mate-
rials,
– impact drilling into walls, concrete and similar
building materials,
– inserting and tightening screws
The user is liable for improper or non-in-
tended use; this also includes continuous in-
dustrial operation.
4Technicaldata
* Speed specifications with fully charged battery
pack.
** The maximum speed is reduced in the lower
torque stages (values in counterclockwise rotation).
5 Machine features
Accessories shown or described are sometimes not
included in the scope of delivery.
The specified illustrations appear at the beginning
of the Operating Instructions.
6 Commissioning
6.1 Changing the battery pack
Inserting the battery pack [2 A]
Removing the battery pack[2 B]
L Battery pack is ready for use immediately upon
delivery and can be charged at any time.
6.2 Light and battery capacity indicator
The LED on the lamp [1-2] is both a light and
a battery capacity indicator
.
X Press the LED light switch [1-1] :
1x ... LED, working area illumination
2x ... capacity indicator, indicates the charging
state of the battery pack (not with NiCd and
NiMH battery packs)
Drilling in metal a
h
= 5,6 m/s
2
K = 1,5 m/s
2
Fastening a
h
< 2,5 m/s
2
K = 1,5 m/s
2
Impact drilling into con-
crete a
h
= 12,4 m/s
2
K = 3,0 m/s
2
Cordless percussion drill PDC 18/4 Li
Motor voltage 18 V
Idling speed* 1st gear 0 - 400 min-1
2nd gear 0 - 850 min
-1
3rd gear 0 - 1850 min
-1
4th gear 0 - 3800 min
-1
Torque for easy/tough fastening
applications 40/60 Nm
Adjustable torque** 1st gear 1,2 - 11,5 Nm
2nd gear 0,8 - 7,2 Nm
3rd gear 0,6 - 4,7 Nm
4th gear 0,6 - 2,6 Nm
Chuck clamping range 1,5 - 13 mm
Drill diameter max. Wood 50 mm
Metal 13 mm
Fastening in pine max.  10 mm
Tool holder in drill spindle 1/4"
Weight without battery pack with
Centrotec 1,3 kg
[1-1] LED light switch
[1-2] LED lamp
[1-3] Bit store
[1-4] On/Off switch
[1-5] Clamping sleeve
[1-6] Drilling/impact drilling selector switch
[1-7] Gear switch
[1-8] Torque thumbwheel
[1-9] Right/left switch
[1-10] Belt clip
[1-11] Button for releasing the battery pack
[1-12] Insulated gripping surfaces (grey shaded
area)
LED green – lit continuously:
charged > 60 %
Cordless percussion drill PDC 18/4 Li

12
PDC 18/4 Li
GB
7 Settings
7.1 Changing direction of rotation [1-9]
• Switch to the left = clockwise rotation
• Switch to the right = counterclockwise rotation
7.2 Changing gear
You can change gear using the gear switch [1-7] .
7.3 Adjusting the torque[1-8]
Fastening
Select the correct torque setting:
Position 1 = low torque
Position 12 = high torque
An
acoustic signal sounds when the preset torque
is reached and the machine then switches off. You
must release and press the ON/OFF switch
[1-4]
again to start the machine.
Drilling
Mark is aligned with drill symbol = maximum
torque.
7.4 Impact drilling
L The machine was designed for impact drilling
into tiles, masonry and stone.
Set the selector switch
[1-6] to the hammer sym-
bol. Set the adjusting wheel
[1-8] to the drill sym-
bol.
8 Tool holder, attachments
L Prior to initial use: apply multi-purpose grease
to the drill spindle and gearbox neck.
8.1 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CENTRO-
TEC tool chucks.
Wear gloves when replacing!
8.2 Chuck [5]
For clamping drill bits and bits with max. shaft di-
ameter of 13 mm.
Clamp tool centrally in the chuck.
8.3 Angle attachment [6]
Drilling and screwdriving at right angle to machine
(partly as an accessory).
8.4 Tool holder in the drill spindle [7]
Bits can be inserted directly into the hexagon sock-
et holder of the drill spindle.
8.5 Depth stop [8]
The depth stop (partly as an accessory) allows the
user to insert screws to a predefined depth. You can
set the dimension by which the screw head pro-
trudes above or is recessed below the surface of the
workpiece.
Depth setting
Turn the housing [8-1] to set the
desired fastening depth. Each
detent position changes the fas-
tening depth by 0.1 mm.
Sleeve A/B must be removed before a screw can be
unscrewed.
LED green – flashing slowly:
charged 30 % – 60 %
LED green – flashing quickly:
charged 0 % – 30 %
LED yellow – lit continuously:
battery is empty
LED red – lit continuously: bat-
tery temperature is outside the
permitted range.
LED red – flashing: indicates a
general fault, e.g. incomplete
contact, short circuit, battery
pack faulty, etc.
CAUTION
Risk of injury
X Always switch off the power tool before adjusting
settings!
WARNING
Risk of injury
X Always disconnect the battery pack before per-
forming any type of work on the machine!
CAUTION
Hot and sharp tools
Risk of injury
X Do not use insert tools that are blunt or defec-
tive.
X Wear protective gloves.

PDC 18/4 Li
13
GB
9 Working with the machine
9.1 On/Off switch [1-4]
Press = ON, release = OFF
L The speed of the machine depends on how far
the on/off switch is pressed in.
9.2 Bit store [1-3]
Magnetic, for storing bits and bit holders.
9.3 Belt clip [1-10]
The belt clip (right/left) allows the user to attach
the machine briefly to work clothing.
9.4 Attaching the additional handle[3]
Always use the additional handle.
X Position the additional handle [3-2] on the ex-
tension of the gearbox housing and engage the
recesses on the additional handle in the lugs on
the housing.
X Turn the handle until secured in position.
L Turn the handle to adjust the position in 30° in-
crements.
L The drilling depth can be adjusted using the
depth stop
[3-1] .
9.5 Acoustic warning signal
Acoustic warning signals sound and the machine
switches off in the following operating states:
10 Service and maintenance
Customer service and repair only
through manufacturer or service
workshops: Please find the nearest
address at: www.festool.com/service
Only use original Festool spare parts!
Order No. at: www.festool.com/service
Note the following information:
– Keep the ventilation slits on the machine free and
clean to ensure adequate cooling.
– Keep the contacts on the machine, charger and
battery pack clean.
For service, maintenance, disposal and
transport of the battery pack, note enclosed
instructions of the battery pack!
11 Environment
Do not dispose of the device in house-
hold waste!
Recycle devices, accesso-
ries and packaging. Observe applica-
ble national regulations.
EU only: In accordance with European Directive on
waste electrical and electronic equipment and im-
plementation in national law, used electric power
tools must be collected separately and handed in
for environmentally friendly recycling.
Information on REACh: www.festool.com/reach
WARNING
Risk of injury
X Always secure the workpiece in such a manner
that it cannot move while being machined.
– Preset torque reached.
– "Block protect", starting torque too high.
– Machine overloaded
WARNING
Risk of injury, electric shock
X Always disconnect the battery pack from the
machine before any cleaning or maintenance!
X All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
235
4