FieldServer FS-8700-84 Release note

ASierraMonitorCompany
APPLICABILITY & EFFECTIVITY
Effective for all systems manufactured after May 1, 2001
Driver Manual
(Supplement to the FieldServer Instruction Manual)
FS-8700-84 Lutron eLumen

FS-8700-84_Lutron_eLumen Manual Table of Contents
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
TABLE OF CONTENTS
1. Lutron eLumen Description.......................................................................................... 1
2. Driver Scope of Supply................................................................................................... 2
1.01 Supplied by FieldServer Technologies for this driver............................................ 2
1.02 Provided by the Supplier of 3rd Party Equipment ................................................... 2
2.1.1. Required 3rd Party Hardware.............................................................................. 2
3. Hardware Connections................................................................................................... 3
4. Configuring the FieldServer as a Lutron eLumen Client ...................................... 5
1.03 Data Arrays/Descriptors ............................................................................................. 5
1.04 Client Side Connection Descriptions........................................................................ 6
1.05 Client Side Node Descriptors .................................................................................... 6
1.06 Client Side Map Descriptors...................................................................................... 7
4.1.1. FieldServer Related Map Descriptor Parameters............................................ 8
4.1.2. Driver Related Map Descriptor Parameters...................................................... 8
4.1.3. Timing Parameters ............................................................................................. 10
4.1.4. System Monitor Command – Time Now......................................................... 11
4.1.5. System Monitor Command – Astro Times...................................................... 11
4.1.6. System Monitor Command – Date................................................................... 12
4.1.7. System Monitor Command – Code Revision Level....................................... 12
4.1.8. System Monitor Command – Bootcode Revision Level ............................... 12
4.1.9. System Monitor Command – Serial Number.................................................. 13
4.1.10. System Monitor Command – Area Status ...................................................... 13
4.1.11. System Monitor Command – Timeclock Status............................................. 14
4.1.12. System Monitor Command – Zone Intensity.................................................. 14
4.1.13. System Monitor Command – Request Panel Emergency Status............... 15
4.1.14. System Monitor Command – System Variable Value................................... 15
4.1.15. System Monitor Command – Wallstation Status........................................... 16
4.1.16. System Monitor Command – Switch Status................................................... 16
4.1.17. System Control Commands containing no Parameters: – Halt Zone......... 17
4.1.18. System Control Commands containing no Parameters: – Stop Scene
Ramp Up............................................................................................................................... 17
4.1.19. System Control Commands containing no Parameters: – Select System
Scene(s)18
4.1.20. System Control Commands containing no Parameters: – Disable
Timeclock until Enabled...................................................................................................... 18
4.1.21. System Control Commands containing no Parameters: – Disable timeclock
until end of day or enable issued...................................................................................... 18
4.1.22. System Control Commands containing no Parameters: – Re-enable
timeclock with complete catchup ...................................................................................... 19
4.1.23. System Control Commands containing no Parameters: – Re-enable
timeclock and do previous event....................................................................................... 19
4.1.24. System Control Commands containing no Parameters: Standard re-enable
timeclock............................................................................................................................... 19
4.1.25. System Control Commands containing no Parameters: Run script(s)....... 20

FS-8700-84_Lutron_eLumen Manual Table of Contents
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.26. System Control Commands containing no Parameters: Toggle system
variable value....................................................................................................................... 20
4.1.27. System Control Commands containing no Parameters: Output temp scene
21
4.1.28. System Control Commands containing no Parameters: Select scene in
area 22
4.1.29. System Control Commands containing no Parameters: Timeclock new
schedule23
4.1.30. System Control Commands containing no Parameters: Set timeclock...... 23
4.1.31. System Control Commands containing no Parameters: Enable
wallstation(s)......................................................................................................................... 24
4.1.32. System Control Commands containing no Parameters: Disable
wallstation(s)......................................................................................................................... 24
4.1.33. System Control Commands containing no Parameters: Simulate
wallstation(s) switch press ................................................................................................. 25
4.1.34. System Control Commands containing no Parameters: Simulate
wallstation(s) switch release.............................................................................................. 26
4.1.35. System Control Commands containing no Parameters: Stop scene ramp
down 26
4.1.36. System Control Commands Containing Parameters: Toggle zone............ 27
4.1.37. System Control Commands Containing Parameters: Fade zone(s) to level
27
4.1.38. System Control Commands Containing Parameters: Ramp zone(s) up... 28
4.1.39. System Control Commands Containing Parameters: Ramp zone(s) down
28
4.1.40. System Control Commands Containing Parameters: Pommel or pulse
zone(s Toggle zone) ........................................................................................................... 29
4.1.41. System Control Commands Containing Parameters: Flash zones aka
“Multi level ( Flash or Warn or Chase )“........................................................................... 30
4.1.42. System Control Commands Containing Parameters: Ramp scene zones
up 30
4.1.43. System Control Commands Containing Parameters: Ramp scene zones
down 31
4.1.44. System Control Commands Containing Parameters: Select system
scene(s) using override times............................................................................................ 31
4.1.45. System Control Commands Containing Parameters: Set system variable
value 32
4.1.46. Listening to switch presses and releases: Enabling switch presses and
releases reporting................................................................................................................ 32
4.1.47. Listening to switch presses and releases: Disabling switch presses and
releases reporting................................................................................................................ 32
4.1.48. Listening to switch presses and releases: Listening to switch presses and
releases 33
4.1.49. Active read on startup: Retrieving names....................................................... 34
Appendix A. Data Tables..................................................................................................... 35
Appendix B. Revision History............................................................................................ 36

FS-8700-84_Lutron_eLumen Driver Manual Page 1 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
1. Lutron eLumen Description
The Serial Lutron eLumen driver allows the FieldServer to transfer data to and from
devices over RS-232 or RS-485 using eLumen protocol. The FieldServer can only be
used operationally as a Lutron Client driver. Any existing Lutron Server drivers are for
FieldServer testing purposes only and cannot be used to emulate a Lutron eLumen
system.
The driver supports the following 3 panels: GRAFIK5000, GRAFIK6000 and
GRAFIK7000. The hardware for all 3 panels is identical. The only differences are limits
in the database. GRAFIK5000 has only 1 CSD link and can have a max of 128 zones.
GRAFIK6000 has 3 CSD links with 512 zones. GRAFIK7000 has 6 links with 512
zones and can communicate with other processors.
The FieldServer eLumen driver implements the following functionality:
Status monitoring of eLumen system data and parameters.
System Control of eLumen.
Status monitoring is achieved by sending status requests to the eLumen system.
Retrieved status data are collected and stored in FieldServer Data Arrays that allow
access by other protocols.
System Control Commands can be configured in the FieldServer to address any groups
of Areas, Zones or Scenes. A mechanism is provided by which the parameters are set
before the command is triggered using the upstream protocol.
Commands are provided to read the names of Areas, Zones and Scenes from the
eLumen to facilitate access by SCADA systems.

FS-8700-84_Lutron_eLumen Driver Manual Page 2 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
2. Driver Scope of Supply
1.01 Supplied by FieldServer Technologies for this driver
FieldServer Technologies
PART # Description
FS-8915-10 UTP cable (7 foot) for RS-232 use
FS-8917-02 RJ45 to DB9F connector adapter
FS-8700-84 Driver Manual.
1.02 Provided by the Supplier of 3rd Party Equipment
2.1.1. Required 3rd Party Hardware
Part # Description
Lutron Panel

FS-8700-84_Lutron_eLumen Driver Manual Page 3 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
3. Hardware Connections
The FieldServer is connected to the Lutron eLumen as shown in connection drawing.
Configure the eLumen according to manufacturer’s instructions
DATE: 11/12/04
BY: MC
(408)-262-2299
BASE NAME:
FILE NAME: FS-T28700-84 .VSD
LUTRON ELUMEN RS-232
CONNECTION DIAGRAM
CAT 5 CABLE
FS-8915-10
LUTRON SERIAL
RS-232 INTERFACE
PART # 470-784
FS-8917-02
FS-8917-02
FUNCTION FROM TO COLOUR
RX RJ45-01 DB9M-02 WHITE
CTS RJ45-02 DB9M-08 BROWN
DSR RJ45-03 DB9M-06 YELLOW
GND RJ45-04 DB9M-05 GREEN
GND RJ45-05 RED
TX RJ45-08 DB9M-03 BLUE
RTS RJ45-07 DB9M-07 ORANGE
DTR RJ45-06 DB9M-04 BLACK
8917-02 WIRE LIST
FS-B2010
RxTx RxTx
EthernetEIA232 USB EIA485
Power OK
Serial
+
-

FS-8700-84_Lutron_eLumen Driver Manual Page 4 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
DATE: 11/12/04
BY: MC
(408)-262-2299
BASE NAME:
FILE NAME: FS-T28700-84 .VSD
LUTRON ELUMEN RS-485
CONNECTION DIAGRAM
eLumen
Processor
To control stations
To dimmer panels
120V 15A
Dedicated Control
Feed
Aux Link (RS-485)
Inter-processor link
User Interface link
Wallstation link
Dimmer panel link
FS-B2010
RxTx RxTx
EthernetEIA232 USB EIA485
Power OK
Serial
+
-

FS-8700-84_Lutron_eLumen Driver Manual Page 5 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4. Configuring the FieldServer as a Lutron eLumen Client
For a detailed discussion on FieldServer configuration, please refer to the FieldServer
Configuration Manual. The information that follows describes how to expand upon the
factory defaults provided in the configuration files included with the FieldServer (See
“.csv” sample files provided with the FieldServer).
This section documents and describes the parameters necessary for configuring the
FieldServer to communicate with a Lutron eLumen Server
1.03 Data Arrays/Descriptors
The configuration file tells the FieldServer about its interfaces, and the routing of
data required. In order to enable the FieldServer for Lutron eLumen
communications, the driver independent FieldServer buffers need to be declared in
the “Data Arrays” section, the destination device addresses need to be declared in
the “Client Side Nodes” section, and the data required from the Servers needs to be
mapped in the “Client Side Map Descriptors” section. Details on how to do this can
be found below.
Note that in the tables, * indicates an optional parameter, with the bold legal value
being the default.
Section Title
Data_Arrays
Column Title Function Legal Values
Data_Array_Name Provide name for Data Array Up to 15 alphanumeric
characters
Data_Array_Format Provide data format. Each Data Array can only take on one
format.
Float, Bit, UInt16,
SInt16, Packed_Bit,
Byte, Packed_Byte,
Swapped_Byte
Data_Array_Length
Number of Data Objects. Must
be larger than the data storage
area required by the Map
Descriptors for the data being
placed in this array.
1-10,000
Example
// Data Arrays
Data_Arrays
Data_Array_Name, Data_Format, Data_Array_Length
Area_status, UInt16, 64
Zone_list, UInt16, 64
Zone_pars, UInt16, 10

FS-8700-84_Lutron_eLumen Driver Manual Page 6 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
1.04 Client Side Connection Descriptions
Section Title
Connections
Column Title Function Legal Values
Port Specify which port the device is connected to the
FieldServer P1-P8, R1-R21
Protocol Specify protocol used eLumen
Baud* Specify baud rate 9600 – Vendor limitation
Parity* Specify parity None
Data_Bits* Specify data bits 8
Stop_Bits* Specify stop bits 1
Handshaking* Specify hardware
handshaking None
Poll _Delay* Time between internal polls 0-32000 seconds, 1 second
Example
// Client Side Connections
Connections
Port, Protocol, Baud, Parity, Data Bits, Stop Bits, Poll_Delay
P1, eLumen, 9600, None, None, 1, 0.100s
1.05 Client Side Node Descriptors
Section Title
Nodes
Column Title Function Legal Values
Node_Name Provide name for node Up to 32 alphanumeric
characters
Node_ID
The eLumen processor
address - only decimal values
allowed e.g. 11 hex has to be
entered as 17.
0-255
Protocol Specify protocol used eLumen
Port Specify which port the device is
connected to the FieldServer P1-P8, R1-R21
Node_type Specifies the eLumen
command and data format Hex, decimal
1Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction manual for
details of the ports available on specific hardware.

FS-8700-84_Lutron_eLumen Driver Manual Page 7 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
Example
// Client Side Nodes
Nodes
Node_Name, Node_ID, Protocol, Connection, Node_type
LUT_GRF6_0, 17, eLumen, P1, hex
1.06 Client Side Map Descriptors
The driver uses Map Descriptors with Lutron commands to build poll messages that
will be sent to the eLumen system. Example Map Descriptors are shown in the next
section. Note the following in the use of Map Descriptors for the Lutron driver:
Lutron command
Every Map Descriptor must have a Lutron command specified so the driver will know
which command to send to the eLumen.
Function
Map Descriptor functions must be correctly specified to implement the functionality
embodied by the specific Lutron command, e.g. a command to retrieve area status
requires a read Map Descriptor whereas a command to toggle zones requires a
write Map Descriptor.
DA_Area_Names, DA_Scene_Names, DA_Zone_Names, xxx_Offset
These are user Map Descriptor fields needed to retrieve area, scene and zone
names from the eLumen. Please refer to the Map Descriptor examples.
Link, Area, Link_station, Switch, Zone, Sys_var, Panel
These are user Map Descriptor fields that must be used as needed with a specific
Lutron command. Please refer to the Map Descriptor examples.
DA_Lut_List, DA_Lut_List_Offset
Lutron commands that allow multiple areas, zones, etc to be specified in one
command e.g. Toggle zones use the areas or zones in the Data Array specified by
DA_Lut_List at an offset specified by DA_Lut_List_Offset to build the poll message.
The list must be filled in before the command is triggered by writing into the Data
Array specified by Data_Array_Name.
DA_Lut_Parms, DA_Lut_Parms_Offset
Lutron commands that use parameters such as delay and fade cycles use the
parameters at the offset as specified by these Map Descriptor fields. Parameters
must be filled in together with the list data if applicable before triggering the
command by writing into the Data Array specified by Data_Array_Name. Please
refer to the Map Descriptor examples.

FS-8700-84_Lutron_eLumen Driver Manual Page 8 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.1. FieldServer Related Map Descriptor Parameters
Column Title Function Legal Values
Map_Descriptor_Name Name of this Map
Descriptor Up to 32 alphanumeric characters
Data_Array_Name
Name of Data Array
where data is to be
stored in the
FieldServer
One of the Data Array
names from “Data Array”
section above
Data_Array_Location Starting location in
Data Array
0 to maximum specified in
“Data Array” section
above
Function Function of Client
Map Descriptor ARS, RDBC, WRBC, WRBX, AWT
4.1.2. Driver Related Map Descriptor Parameters
Column Title Function Legal Values
Node_Name Name of Node to fetch
data from
One of the node names
specified in “Client Node
Descriptor” above
GRAFIK_command Specifies the command to be sent to the
eLumen.
A list of commands is
provided in Appendix A.
Link Wallstation link number
0–11 for
GRAFIK_command:
ena_wallstation,
dis_wallstation,
sim_ws_sw_press,
sim_ws_sw_rls,
0-31 for
GRAFIK_command:
wallstation_status,
switch_status,
Area GRAFIK system area
number 0–511
Link_station Wallstation on link’s
number 0–31
Switch Wallstation switch
number 0–31
Zone GRAFIK system zone
number 0–511
Sys_var GRAFIK system variable
number 0–65535
Panel GRAFIK panel number 0–511

FS-8700-84_Lutron_eLumen Driver Manual Page 9 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
Column Title Function Legal Values
DA_Lut_List
Name of Data Array that
contains a list of zones
or areas, etc, needed to
build the poll message.
Any Data Array name. If
not listed under Data
Arrays the driver will
auto-create the Data
Array.
DA_Lut_List_Offset
The offset into the
DA_Lut_List Data Array
where the driver will
retrieve the list data
when building the poll
message.
0 to the maximum offset
into the DA_Lut_List
Data Array.
DA_Lut_Parms
Name of Data Array
containing parameters
needed to build the poll
message.
Any Data Array name. If
not listed under Data
Arrays the driver will
auto-create the Data
Array.
DA_Lut_Parms_Offset
The offset into the
DA_Lut_Parms Data
Array where the driver
will retrieve the
parameters when
building the poll
message.
0 to the maximum offset
into the DA_Lut_Parms
Data Array.
DA_Area_Names Name of Data Array where retrieved area
names will be stored.
Any Data Array name. If
not listed under Data
Arrays the driver will
auto-create the Data
Array.
DA_Area_Names_Offset
The offset into the
DA_Area_Names Data
Array where retrieved
area names will be
stored.
0 to the maximum offset
into the
DA_Area_Names Data
Array.
DA_Scene_Names Name of Data Array where retrieved scene
names will be stored.
Any Data Array name. If
not listed under Data
Arrays the driver will
auto-create the Data
Array.
DA_Scene_Names_Offs
et
The offset into the
DA_Scene_Names Data
Array where retrieved
scene names will be
stored.
0 to the maximum offset
into the
DA_Scene_Names Data
Array.

FS-8700-84_Lutron_eLumen Driver Manual Page 10 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
Column Title Function Legal Values
DA_Zone_Names Name of Data Array where retrieved zone
names will be stored.
Any Data Array name. If
not listed under Data
Arrays the driver will
auto-create the Data
Array.
DA_Zone_Names_Offse
t
The offset into the
DA_Zone_Names Data
Array where retrieved
zone names will be
stored.
0 to the maximum offset
into the
DA_Zone_Names Data
Array.
Area_Names_Start
Area_Names_End
Start and end numbers
of area name to be
retrieved with
get_names cmd
0–511
Scene_Names_Start
Scene_Names_End
Start and end numbers
of scene name to be
retrieved with
get_names cmd
0–32,768
Zone_Names_Start
Zone_Names_End
Start and end numbers
of zone name to be
retrieved with
get_names cmd
0–511
Length
Length of Map
Descriptor. The length is
an indication of the
number of data elements
this Map Descriptor is
responsible for updating.
It is used in the overall
points calculation of the
FieldServer.
See example Map
Descriptors for individual
lengths per Map
Descriptor.
4.1.3. Timing Parameters
Column Title Function Legal Values
Scan_Interval Rate at which data is polled 0s to 32000s

FS-8700-84_Lutron_eLumen Driver Manual Page 11 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.4. System Monitor Command – Time Now
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Length
Time_now, 5s, Time_now, 0, rdbc, LUT_GRF6_0, time_now, 1
Data storage in Data Array
Position from offset Description:
0 Minutes from midnight
4.1.5. System Monitor Command – Astro Times
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Length
Astro_times, 5s, Astro_times, 0, rdbc, LUT_GRF6_0, astro_times, 2
Data storage in Data Array
Position from offset Description:
0 Sunrise minutes from midnight
1 Sunset minutes from midnight

FS-8700-84_Lutron_eLumen Driver Manual Page 12 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.6. System Monitor Command – Date
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Length
Date, 5s, Date, 0, rdbc, LUT_GRF6_0, date, 4
Data storage in Data Array
Position from offset Description:
0 Month ( 1-12 )
1 Day of month ( 1-31 )
2 Year ( 0-99 )
3 Day of week ( 1-7, 1=Sunday )
4.1.7. System Monitor Command – Code Revision Level
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Length
Code_rev, 5s, Code_rev, 0, rdbc, LUT_GRF6_0, code_rev_level, 1
Data storage in Data Array
Position from offset Description
0 Code revision level
4.1.8. System Monitor Command – Bootcode Revision Level
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Length
Bootcode_rev, 5s, Bootcode_rev, 0, rdbc, LUT_GRF6_0, bootcode_rev_level, 1
Data storage in Data Array
Position from offset Description
0 Bootcode revision level

FS-8700-84_Lutron_eLumen Driver Manual Page 13 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.9. System Monitor Command – Serial Number
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Length
Serial_num, 5s, Serial_num, 0, rdbc, LUT_GRF6_0, serial_no, 1
Data storage in Data Array
Position from offset Description
0 Serial number
4.1.10. System Monitor Command – Area Status
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Area, Length
Area_sts_00, 1s, Area_status, 0, rdbc, LUT_GRF6_0, Area_status, 0, 2
Area_sts_01, 1s, Area_status, 2, rdbc, LUT_GRF6_0, Area_status, 1, 2
Data storage in Data Array
Position from offset Description
0 System scene on status
1 Sequence running status
Note: This command stores 2 data values. To prevent overlaps, remember to increment Data_Array_Offset by 2 when referencing the same Data
Array with other Map Descriptors.

FS-8700-84_Lutron_eLumen Driver Manual Page 14 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.11. System Monitor Command – Timeclock Status
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Area, Length
Tclk_sts_00, 1s, Tclk_status, 0, rdbc, LUT_GRF6_0, timeclock_status, 0, 4
Tclk_sts_01, 1s, Tclk_status, 4, rdbc, LUT_GRF6_0, timeclock_status, 1, 4
Data storage in Data Array
Position from offset Description
0 Schedule number
1 Next event type (1 = no more events, 2 = timeclock disabled, 3 = astronomic event, 4 = realtime event )
2 Next event time ( minutes past midnight )
3 Next script
Note: This command stores 4 data values. To prevent overlaps, remember to increment Data_Array_Offset by 4 when referencing the same Data
Array with other Map Descriptors.
4.1.12. System Monitor Command – Zone Intensity
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Zone, Length
Zn_int_00, 1s, Zone_int, 0, rdbc, LUT_GRF6_0, zone_intensity, 0, 1
Zn_int_01, 1s, Zone_int, 1, rdbc, LUT_GRF6_0, zone_intensity, 1, 1
Data storage in Data Array
Position from offset Description
0 Zone intensity ( 0-127 )
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data
Array with other Map Descriptors.

FS-8700-84_Lutron_eLumen Driver Manual Page 15 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.13. System Monitor Command – Request Panel Emergency Status
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Panel, Length
Pnl_emerg_sts_00, 1s, Pnl_emerg_sts, 0, rdbc, LUT_GRF6_0, pnl_emerg_status, 0, 1
Pnl_emerg_sts_511, 1s, Pnl_emerg_sts, 511, rdbc, LUT_GRF6_0, pnl_emerg_status, 511, 1
Data storage in Data Array
Position from offset Description
0 Panel emergency status
0 = normal; 1 = override
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data
Array with other Map Descriptors.
4.1.14. System Monitor Command – System Variable Value
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, Sys_var, Length
Sys_var_00, 1s, Sys_vars, 0, rdbc, LUT_GRF6_0, sys_var_val, 0, 1
Sys_var_01, 1s, Sys_vars, 1, rdbc, LUT_GRF6_0, sys_var_val, 1, 1
Data storage in Data Array
Position from offset Description
0 System variable value
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data
Array with other Map Descriptors.

FS-8700-84_Lutron_eLumen Driver Manual Page 16 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.15. System Monitor Command – Wallstation Status
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, link, link_station, Length
Wall_st_sts_0000, 1s, Wall_st_sts_00, 0, rdbc, LUT_GRF6_0, wallstation_status, 0, 0, 32
Wall_st_sts_0001, 1s, Wall_st_sts_00, 32, rdbc, LUT_GRF6_0, wallstation_status, 0, 1, 32
Data storage in Data Array
Position from offset Description
0-31 All switches on station and their priority.
Note: This command stores 32 data values. To prevent overlaps, remember to increment Data_Array_Offset by 32 when referencing the same
Data Array with other Map Descriptors.
Implementation note: The wallstation status command retrieves the status of all 32 switches defined on a wallstation. If you only want to retrieve
the status of a few individual switches, rather only use the switch status Map Descriptor as described below.
4.1.16. System Monitor Command – Switch Status
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, link, link_station, switch, Length
Sw_sts_000, 1s, Sw_sts_00, 0, rdbc, LUT_GRF6_0, switch_status, 0, 0, 0, 1
Sw_sts_001, 1s, Sw_sts_00, 1, rdbc, LUT_GRF6_0, switch_status, 0, 0, 1, 1
Data storage in Data Array
Position from offset Description
0 Switch status and priority
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data
Array with other Map Descriptors.
Implementation note: The switch status command only retrieves the status of one switch on a wallstation. To retrieve other switch statuses, use
additional switch status Map Descriptors or else use the wallstation status Map Descriptor to retrieve the status of all 32 switches. When using
both wallstation status and switch status Map Descriptors in the same configuration, it is not permissible to have the target Data Arrays overlap.

FS-8700-84_Lutron_eLumen Driver Manual Page 17 of 36
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com
Tel: [phone] Fax: [phone] Toll_Free: 888-509-1970 email: [email protected]
4.1.17. System Control Commands containing no Parameters: – Halt Zone
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, DA_Lut_List, DA_Lut_List_Offset, Length
Zone_halt, Lut_triggers, 0, awt, LUT_GRF6_0, halt_zone, Zone_list, 0, 1
DA_Lut_List data setup
Position from DA_Lut_List_Offset Description
0-63 Zone(s) to halt
Note: After setting up the zone numbers to halt in the DA_Lut_List Data Array, trigger this command by writing the number of zones to halt into the
Data Array specified by Data_Array_Name at an offset specified by Data_Array_Offset.
4.1.18. System Control Commands containing no Parameters: – Stop Scene Ramp Up
// Client side Map Descriptors
Map_Descriptors
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name, GRAFIK_command, DA_Lut_List, DA_Lut_List_Offset, Length
Stop_scn_rmp_up, Lut_triggers, 1, awt, LUT_GRF6_0, stop_scene_ramp_up, Area_list, 0, 1
DA_Lut_List data setup
Position from DA_Lut_List_Offset Description
0-31 Area(s) with scenes to stop ramp up
Note: After setting up the area numbers to stop scene ramps in the DA_Lut_List Data Array, trigger this command by writing the number of areas
into the Data Array specified by Data_Array_Name at an offset specified by Data_Array_Offset.