Filix RDT 100 User manual

TRIMLESS TRIM TRIM
RDT 100
INSTALLATION INSTRUCTIONS (FIXTURE)
All dimensions are given according to the SI system of units (mm, kg, °C), additional dimensions that are written in brackets,
are given according to the U.S. measurement system (in, lbs, °F)
FLOOR
Ta I 40°C
22
IP67 AL608224 VDC
GENERAL REMARKS ON SAFETY
·READ ALL OF THESE INSTRUCTIONS BEFORE INSTALLING
FIXTURES.
·KEEP ALL OF THE INSTRUCTIONS FOR FUTURE
REFERENCE.
·INSTALLATION IS TO BE PERFORMED BY A QUALIFIED
ELECTRICIAN ONLY.
·ALL INSTALLATIONS ARE TO CONFORM TO THE
STANDARDS OF THE NATIONAL ELECTRICAL CODE AS
WELL AS ALL LOCAL JURISDICTIONAL CODES AND
REGULATIONS.
·PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH
THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
·TURN OFF POWER BEFORE INSTALLING FIXTURE.
·DO NOT OPEN THE LUMINAIRE AS IT WILL ANNUL THE IP
RATING OF LUMINAIRE AND VOID THE WARRANTY.
·THE SURFACE TEMPERATURE OF THE FIXTURE IS ≈40°C
(104°F) AND IMPOSES NO LIMITS ON INSTALLATION.
·CALCULATE THE MAXIMUM POWER CONSUMPTION AND
USE APPROPRIATELY SIZED DRIVERS/CONTROLLERS.
·THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS
LUMINAIRE CANNOT BE REPLACED; IF THE CORD IS
DAMAGED, THE LUMINAIRE WILL NO LONGER BE USABLE,
AND THE LUMINAIRE MUST BE REPLACED.
·LUMINAIRE IS DESIGNED AND TESTED FOR DRIVE OVER
TO 15000N AND CANNOT BE USED IN ROAD LINES WHERE
THE FIXTURE IS EXPOSED TO A HORIZONTAL STRESS
DUE TO BREAKING, ACCELERATION AND CHANGE OF
DIRECTION.
IK10 15000 N
1/3
www.filixlighting.com
WARRANTY
ALL PRODUCTS ARE FACTORY TESTED AND ARE GUARANTEED FREE
FROM FACTORY DEFECT FOR A PERIOD OF 36 MONTHS UNDER
FOLLOWING TERMS:
·PRODUCT HAS NOT BEEN SUBJECT TO INCORRECT VOLTAGE OR
POLARITY CONNECTION.
·PRODUCT HAS NOT BEEN SUBJECT TO PHYSICAL OR
ATMOSPHERIC DAMAGE.
·PRODUCT HAS BEEN RETURNED AND FACTORY EVALUATED FOR
DEFECT OR MALFUNCTION.
·ALL DRIVERS AND CONTROLLERS ARE APPROVED FOR USE BY
FILIX.
·THE LUMINAIRE FACTORY SEAL ( IP RATING ) HAS NOT BEEN
COMPROMISED
THE MANUFACTURER ACCEPTS NO RESPONSIBILITY FOR DAMAGE TO
PERSONS OR PROPERTY ARISING THROUGH IMPROPER USE OR
INSTALLATION.
ANY MODIFICATION OF THE LUMINAIRE WILL VOID ANY AND ALL
WRITTEN OR IMPLIED WARRANTIES.
STANDARD REPLACEMENT AND NORMAL
SERVICING TERMS.
ALL ELECTRONIC AND OTHER CONSUMABLE COMPONENTS ARE
SUBJECT OF EXCHANGE AFTER 36 MONTHS OF OPERATIONS.
PRODUCT PERFORMANCE DEPENDS OF CRITICAL ELECTRONIC AND
OTHER COMPONENTS WHICH CAN BE SERVICED WITH OFFICIAL
DEALER OR DIRECTLY WITH THE MANUFACTURER.
MANUFACTURER HOLDS THE RIGHT TO REPAIR AND CHANGE
COMPONENTS AS PER CURRENT COMPONENT AVAILABILITY.
MANUFACTURER CANNOT BE HELD LIABLE FOR COMPONENTS AND
OTHER EXPENSES ( DE-INSTALLATION, INSTALLATION, SHIPPING,
ETC.) INCURRED DURING THE PROCESS OF PRODUCT IMPROVEMENT
AND SERVICING.
THE LIGHT SOURCE CONTAINED IN THIS LUMINAIRE SHALL ONLY BE
REPLACED BY THE MANUFACTURER OR HIS SERVICE AGENT OR A
SIMILAR QUALIFIED PERSON.

TRIM
TRIMLESS TRIM
FIXTURE DIMENSIONS
WIRING
WIRE MARKINGS
+ BLACK WIRE
- WHITE WIRE
OPTION WITH SINGLE LED COLOR
www.filixlighting.com
2/3
NOTE:
CONTROL GEAR USED TO POWER THIS LUMINAIRE SHALL BE SELV TYPE; HIGHEST ALLOWED Uout TO BE MAX 10% OF
THE NOMINAL VOLTAGE OF CONTROL GEAR;MAXIMUM ALLOWED WIRING DISTANCE BETWEEN CONTROL GEAR AND
LUMINAIRE WITH STANDARD SUPPLIED CABLE IS 9 m OR 30'. INSTALLATION OF LONGER WIRING LENGTHS SHOULD BE
DISCUSSED WITH MANUFACTURER PRIOR THE FIXTURE ORDERING.
WHERE LUMINAIRE IS DELIVERED WITH CONNECTING LEADS AND WITHOUT A MEANS OF CONNECTION TO THE POWER
SUPPLY TERMINAL BLOCKS MAY BE USED (TERMINAL BLOCKS NOT SUPPLIED BY MANUFACTURER). TERMINAL BLOCKS
SHALL BE IN THE SAME IP RATING AS THE LUMINAIRE ITSELF, WITH RATED VOLTAGE OF MIN. 400 V AND RATED
CONNECTION CAPACITY OF 10A. CONNECTION WIRE ENDS COMING FROM POWER SUPPLY TO BE PREPARED AS
TERMINAL BLOCK MANUFACTURER RECOMMENDS. TERMINAL BLOCK SHOULD BE PLACED IN A LOCATION WHERE IT
DOESN'T NOT AFFECT THE LUMINAIRE OPERATION.

1. ADJUST PIN POSITION TO GET ANGLE BETWEEN -20°&20°.
INSTALLATION GUIDE
2. REMOVE COVER FROM HOUSING
3. CONNECT SUPPLY CABLE TO FIXTURE CABLE
4. ARRANGE CABLE IN TO HOUSING
5. PUSH THE FIXTURE INSIDE HOUSING
3
5
2
4
8. LIFT THE FIXTURE FROM THE INSTALLATION HOUSING WITH SUCTION-CUP TOOL
7
PIN -20° ANGLE 0° ANGLE 20° ANGLE
3/3
www.filixlighting.com