FIM Flexy Twin Operator's manual

Flexy Twin

Tel. [phone]
e-mail: [e-mail]
www.fim-umbrella.com
FLEXY TWIN
INSTRUCTIONS FOR ASSEMBLY AND
RECOMMENDATIONS FOR USE
READ THIS HANDBOOK IMMEDIATELY
These instructions have to be handed over to the end-user of the product who has to read and keep them.
These instructions are provided for an easy set-up of your FLEXY TWIN and for your safety. It is essential that the given
instructions are followed carefully.
Failure to do so may result in injury to people or damage to materials. If in doubt always contact a technical expert.

This symbol indicates very important information. Strictly follow instructions accompanied by this symbol. This
does not mean that the other information contained in this handbook is not important.
Keep this handbook for future reference.
IMPORTANT SAFETY INSTRUCTIONS

APPLIES TO ALL IN THIS SECTION
1. INSTRUCTION
Please read and follow all the instruction. Only one manual is supplied for all the possible combinations of the
FLEXY TWIN.
Damage or injuries may result if the FLEXY TWIN is not assembled and used as described in the instruction.
For safe use it is essential that anyone using the FLEXY TWIN read all the instruction in advance.
Only persons familiar with the safety aspects of the FLEXY TWIN should operate the FLEXY TWIN.
2. PRECAUTIONS
The FLEXY TWIN principally is a protection from the sun, not a protection against all bad weather. It must be
closed in presence of strong winds or thunderstorms, as well as
heavy rain or snow (danger of water pooling on the cover).
Always close the FLEXY TWIN canopies whenever the FLEXY TWIN is not under control.
The base freestanding base must be weighed down with all supplied steel weights.

e-mail: [e-mail]
www.fim-umbrella.com
ASSEMBLY INSTRUCTIONS
COMPONENTS (Pict. 1, 2):
Pict. 1A – FLEXY TWIN WITH A SINGLE CANOPY
(Fig. 2A) Nr 1 sliding canopy (A) with the crossbar (C)
(Fig. 3A) Nr. 1 Upright pole (DA)
(Fig. 4a) Nr 1 Lever group (E) and a bag containing Allen keys of 3 (e3)- 4 (e4)- 5 (e5)
(Fig. 5A) Nr 1 hot dip galvanized steel base (F), set of steel ballasts, a bag of hardware (H) containing 6 feet (f),
4 screws M 10x30 (d), an Allen key 6 (e6).
Pict. 1B – FLEXY TWIN WITH A DOUBLE CANOPY
(Fig. 2B) Nr 2 sliding canopies (A) with the crossbar (C)
(Fig. 3B) Nr. 1 Upright pole (DB)
(Pict. 4B) Nr 2 Lever groups and a bag containing Allen keys of 3 (e3)- 4 (e4)- 5 (e5)
(Pict. 5) Nr 1 hot dip galvanized steel base (F), set of steel ballasts, a bag of hardware (H) containing 6 feet (f), 4
screws M 10x30 (d), an Allen key 6 (e6).
FREESTANDING BASE ASSEMBLY AND POSITIONING (Pict. 6A, 6B and 6C)
Take out the content of the bag of hardware (H).
Screw the feet (f) to the base (F), put the base where you want to assemble Flexy Twin. Make sure that the base is level using the
adjustable the feet (f).
Mount the upright pole (DA) or (DB) to the base (F) with 4 screws (d) and tighten them well with an Allen key (e6).
Place the set of steel ballasts (G’) (G’’) on the carrier plate and bolt the ballasts firmly down.
MOUNTING THE SLIDING CANOPY (Pict.7,8,9)
Remove 2 screws (h) from the crossbar (C)
Remove the screw (i) and washer (M) from the lever group (E) with an Allen key (e3).
Insert the crossbar (C) into the sliders of the canopy (A) and make sure that the two ends of the cord are not tangled together and
stay parralel.
Fix the lever group (E) to the crossbar (C) with the screws (h).
Δ CAUTION: tighten the screws with an Allen key (e5).
MOUNTING THE SLIDING CANOPY ON THE POLE (Pict. 9,10,11)

CAUTION: To avoid damage the operation has to be done simultaneously by two persons with 2 step ladders.
Raise the sliding canopy and join the lever group (E) to the pin (P) of the upright pole (DA or DB).
Remount the flange (I) and fix everything with 2 screws (g).

CAUTION: when the lever group (E) is joint to the pin (P) push the end of the canopy facing up while 2 screws (g) are
pulling. It should be firmly tightened.
Pull the lever group and tilt the canopy on one side. Insert the washer (M) into the buttonhole (R) and fix it with the screw (i).

CAUTION: The procedure is necessary for the wind resistance.
Push the slider (N’) against the lever group (E) and screw the handwheel stem in the hole of the crossbar (C).
Remove the weight (S) applied on the double cord, the weight is divided in 2, put it back after the cord (O) is inside the pulley
(T).
Important: it is essential for the subsequent smooth operation of the canopy that the two ends of the cord are kept extended
and not tangled together .

e-mail: [e-mail]
www.fim-umbrella.com
The Flexy Twin is now ready to be used. Pulling one end of the cord the canopy will slide fully open, pulling the other end of the
cord the canopy will close. In case the canopy is opened or closed block the cord in the rope cleat fixed on the lever (Q). To
change the canopy tilt pull the lever (Q).
IF THE PURCHASED FLEXY TWIN IS COMPOSED OF 2 CANOPIES THE ABOVE MENTIONED OPERATIONS
SHOULD BE REPEATED FOR EACH CANOPY.
MAINTENANCE AND CARE
CLEANING AND LUBRICATION OF THE CROSSBAR
For proper operation of opening and closing, Flexy Twin crossbars have to be cleaned and lubricated periodically with silicone spray
lubricant.
CLEANING THE FABRIC PANELS
The panels can be cleaned by hand with a smooth cloth, lukewarm water (about 30°C ≈ 85°F) and a common detergent for delicate
fabrics. After extensive rinsing the material has to be dried. To extend the life span of the fabric, it is advisable not to perform this
operation in the bright sun.
For washing in industrial washing machines, take the cover off the structure and have it washed with a mild detergeant, delicate
program, extensive rinsing and water temperature not exceeding 40°C (≈ 110°F). Have it dried at the air (do not tumble dry!) and
do not iron.
STORING FLEXY TWIN AT THE END OF THE SEASON
To extend the life span of the product, it is advisable to disassemble and store the awning it away in a dry place at the end of the
season. Before storing away your FLEXY clean the structure with a damp cloth and dry it. For the cleaning of the cover see the
preceeding paragraph.
 CAUTION: Check the integrity of all components. Should any part be damaged contact the dealer where it was
purchased and order the required spare parts.
Touch up any possibly chipped paint. Lightly lubricate all moving parts with silicon spray.
Important: to avoid damage caused by mold or oxidation never put your FLEXY TWIN away when it is wet or damp.
REMOVAL OF THE CANOPY PANELS (Page 11)
Remove the small phillips screws holding the fabric panels inside the rib channel. Slide out the fabric.
.

Fig. 1A Fig. 1B
Fig. 2A Fig. 2B
Fig. 5
Fig. 3BFig. 4A Fig. 4B
B'
C
AC
A
C
A
DA DB
e3 e4 e5
EE E
e3 e4 e5
G'
G'
G''
F
H
e6
f
d
Fig. 3A
B''
G''
CARRIER PLATE PLUS WEIGHT PLATES

G''
Fig. 6A Fig. 6B
f
d
d
d
dd
d
d
dd
f
f
f
f
f
G'
G'
G''
F
DA
DB
G''
f
f
f
f
f
f
G'
G'
G''
F
I
I
I
L
g
gg
g
g
g
L
P
P
P
Fig. 6C
220 V
SINGLE CANOPY UNIT
DUAL CANOPY UNIT

C
Fig. 9
Fig. 8
h
C
h
i
M
E
A
h
h
E
m
C
O
O
h
E
O
N
h
C
Fig. 7
N
N
N
N
N'
N'
N
N
N
N
N'
E
P

E
I
g
g
P
Fig. 10

M
i
E
R
Q
Fig. 11

m
N'
S
O
T
C
S
Fig. 11

FIM Flexy Panel Fastening Instructions
In order to make the Flexy Panels easier to install, with a cleaner look, we have updated
the process to fasten the panels into the track.
Slide the panel into the tracks on the
bottom of the support arms, making sure
the white welt strip is facing up to the top
of the awning, which is the rounded side of
the support arm
Position the panel so the finished edge of
the fabric is flush with the end of the
support arm, and grab one of the included
fastening screws
Start the screw so it will pinch the welt
cord in the track, making sure you do not
push back the panel in the process. Note
that the screw needs to start in the small
gap between the welt and the aluminum
groove
Turn in the screw carefully – it will grab
both the welt and the aluminum and lock
the panel firmly in position
The finished look from top. Note the screw
head is cleanly flush with the end of the
support arm. Repeat process on the
opposite end. You will need to stretch the
panel slightly to be flush on that side as
well, giving the panel a smooth, wrinkle
free appearance