FINGERSAFE MK1A User manual

FINGERSAFE MK1A & MK1B
FITTING INSTRUCTIONS
TOOLS REQUIRED FOR FITTING FINGERSAFE
> Cordless drill (or screwdriver)
> Stanley knife (always keep the blade sharp)
> Strong scissors, tin snips, or hacksaw
> Posidrive bit
> Pencil
> Self-drilling screws for wood, steel and aluminium doors (provided)
The screws provided are for wood and metal doors; if installing in wood, make sure
the electric screwdriver is set to a low tension.
Fingersafe is easy to fit and very reliable when installed correctly. It is essential that these instructions
are followed carefully. We can accept no liability or responsibility for incorrect installation. Fingersafe
can be installed in 95% of doors, however, it is not suitable for the following types of doors; double
swing doors; doors with rising or declining butt hinges; sliding doors.
There are many ways to fit our finger guards. All fitting instructions are contained on the technical
page of our website www.fingersafe.com.au. We suggest you review all fitting instructions to ensure
you fit the finger guards in the manner most appropriate to your door.
www.ngersafe.com.au
4 Craig Road, Donvale 3111
Tel: [phone]
Email: enquiry@ngersafe.com.au
NO LIABILITY WHATSOEVER ACCEPTED IF THESE INSTRUCTIONS ARE NOT FOLLOWED
COMPONENTS OF FINGERSAFE
1. Check the stability of the door and hinges by opening the door at a 45 degree angle and gently but
firmly exerting lateral and vertical pressure. This will show any instability or damage in the door or frame
which must be repaired before you start. If the door has a closer attachment, you must check its
effectiveness. If the door closes easily without Fingersafe, it will continue to do so once Fingersafe is
installed.
2. After any necessary door maintenance, bring all the tools to the side of the door that swings away from
you, and pull the door closed tight.
3. Measure from the bottom of the door to the bottom side of the frame at the top. Subtract 3/4 inch (20
mm) for clearance and cut the fixing strip and pleated panel square to length if necessary.

MK1A INSTALLATION INSTRUCTIONS FOR STANDARD HINGED DOOR
THESE INSTRUCTIONS MUST BE FOLLOWED PRECISELY IN ORDER TO VALIDATE THE 2 YEAR GUARANTEE
Insert TEK screws on alter-
nating sides, keeping cor-
ners firmly in place. Ensure
screws are also fastened
within 20mm of the top and
bottom of the fixing strips.
Open door 90 degrees and align 1
inch side of pleated panel to frame
fixing strip. Snap in position top to
bottom.
Insert 3 inch panel of Finger-
safe in door fixing strip.
Add TEK screws through
both fixing strip and Finger-
safe.
BIRDS EYE VIEW shows Fingersafe fitted with the door closed.
When bent, hold corner of L
firmly in corner of frame and
door. Align with bottom of
door.
With Stanley knfie separate
strips at corner and remove
spacer.
FITTING TIPS
After installing fixing strip, the 1
inch panel must be snapped into
frame fixing strip FIRST.
See no. 4.
When snapping the Fingersafe
panels in position, 3 distinct
clicks per side signal a complete
installation.
1234
56
Ensure when screwing into door side the screw
should go through the module and fixing strip as
shown.
Ensure when screwing onto frame
side the screw should go through
module where indicated to allow
the module to close flush.

MK1B INSTALLATION
FOR STANDARD HINGED DOOR
Butt L shaped edge to the door
side of hinges while aligning with
top and bottom of the door. Secure
completely with TEK self tapping
screws.
Ensure screws are also fastened
within 20mm of the top and bottom
of both sides of the finger guard.
Roll the MK1B over the hinges
and butt the T shape to hinges on
frame side. Align with L shape top
and bottom. Secure with TEK self
tapping screws and remove
cellophane protective membrane.
MK1B must be cut square aligned
with top and bottom of door.
Architrave frame fitted with MK1B reversed,
due to limited space on the frame side.
TYPICAL INSTALLATION EXCEPTION TO TYPICAL
FITTING TIPS:
1) Both the L and T must be parallel to door and frame and each other for maximum protection and
wear.
2) The screws on the L side must be secured first.
3) Do not fit the MK1B over hinges that are proud of the door / frame. Either cut to fit finger guard
only above / between / below hinges OR fit a 10mm width (by the thickness of the hinge) packing
strip to the door / frame to provide a continuous flat surface to fix the finger guard.
Measure height of the
hinge side of door. Cut
MK1B square to this
length.