Finwing Technology Travelerplane T1160 User manual

USER MANUAL
Travelerplane T1160
FINWING TECHNOLOGY
WWW FINWINGHOBBY COM
PATENT PENDING
..
Fin inghobby
Finwinghobby

./ .
This manual aims to help direct the user on how to build the Traveler RC plane.
Please visit the finwing cn finwinghobby com official website for more introductions.
Please read through the manual carefully before installation and flying
Warning:
1 This model airplane is not a toy not recommended for children under 14 years old., ,
2. Be cautious and prepared while flying this plane as a range of issues could lead to a crash
including the environment/weather, speed, pilot error, improper building/testing,
interference or other component failures
3. Flying field: Choose an adequate flying space at least 100 meters long/wide and in an unpopulated
and non-built up area for safe flying. This includes avoiding flying over cities or other populated areas.
4. Please don't fly this model airplane in bad weather including rainy and/or windy environments.
5. Remember to unplug your flight/video battery when not in use to avoid any interference to others
who might be on similar channels.
6. Please remember switch on the transmitter first before connecting the battery, and disconnect
the battery first before switching off your transmitter.
7. Keep away from the propeller when the Airplane is powered as it can be dangerous and could
lead to injury. Keep the powered plane away from children at all times to avoid any accidents or injury.
.

Wing Span 1160MM(46")
Lenght 860MM(33 8”).
Wing Area 20.0 sq dm (310.0 sq in) <Main-Wing Area)
Material Color EPP (Black or White) EPO White/
/Black EPP White EPP and EPO the wegiht is variable
FPV Weight Approximately 1.0-1.2kg(2.2Ib-2.6Ib) 3S 2200mah-5200mah
Testing flight weight of 1.205kg is quite easy (with Stock Power system
Power System <Kits not including Power parts>
Finwing Travelerplane Specifications
Motor 2PCS Brushless Motor CW and CCW Max. 170W Per motor()
ESC 2PCS ESC 15A BEC 2A
Servo 4 PCS 9G Servo
Propeller CW /CCW 6045
Battery Recommend 3S 2200-5200mah
Traveller Suitcase, Aluminium Frame reinforced

H
. +/- .Setting CG at H 20MM
CG Setting.
Black White EPP and EPO/
LR
L
R
'
-=
It s normal if looks like the elevator a little up reflexed
Pre condition is R L
Center of Leading edge
Bottom of Rear edge
Place the plane levelly at platform
Measure the horizontal wing very important()
P1
Hole
We tested all kinds of CG Setting proved at the range
between Front and Back of 2 0MM based on the hole is the best
.
.

Fuselage Gluing Covers and Plywood()
Please according to the following stepsbuild
Step 1
gluing shoulder cover
#
Step 2
gluing Plywood
#
Step 3
Locker s Plywood
#
'
Step 4#
Gluing fuselage tail cover
Important Note be sure let glue dry at least 12 hours before installing other parts:
Be careful I m big hole
don t use that small hole one
'
'Be careful I m big hole
don t use that small hole one
'
'
Step Gluing
Motor Mount plywood
#5
P2
Step 3
Locker s Plywood
#
'
Plywood

Wings(/ )Left Right wing is the same
Step 1 gluing Covers#
Step 2
Screws secure the Locker
#
Recommend to reinforce the
Aileron linkage with tapewrapping
Step gluing Covers#3
Important Note be sure let glue dry at least 12 hours before installing other parts:
Recommend to reinforce the
linkage with tapeWrapping
Reinforcement carbon tubes has already been pre glued-
Cut off
Please according to the following stepsbuild
P3

Fuselage Tail EPP EPO&(/)
Wing Lock
Linkage
Linkage
Screw secure the lockers
Note Black EPP White EPP and White EPO is the same:/
Cut off
Cut off
P4
For Metal linkage
For servo Horn
For Wing Lock
Φ20.
Φ23.
Φ30.

Fuselage EPP EPO(/ )
Use hobby knife cut a hole let ESC and Servo wire pass through
Note Black EPP White EPP and White EPO is the same:/
ESC pass through the hole like this
P5

Install servos(/-)Fuselage Main Wing
Enlarge the servo bay to have enough
space for the servo arm moving freely
Black EPP White EPP and White EPO is the same/
P6

Install servos Main Wing-()
Neutralize servo first
Install servo as photos displayed
Black EPP White EPP and White EPO is the same/
P7

Install servos Main Wing-()
The bottom hole
The holefirst
The holefirst
The bottom hole
P8

P9 Motor ESC Propeller//

Motor ESC Propeller//
Solder in parallel
Note Move the heat shrink tubing inside first:
Black EPP White EPP and White EPO is the same/
P10

Horizontal Wing
LR
L
R
'
-=
It s normal if looks like the elevator a little up reflexed
Pre condition is R L
Servo Horn
Choose the hole or the second hole won t be
big difference recommend try the top hole
:
'
,
top
Center of Leading edge
Bottom of Rear edge
Place the plane levelly at platform
Measure the horizontal wing very important()
P11

Horizontal Wing
Center of Leading edge
Example of measurement
P12
Bottom of Rear edge

Vertical wing Tail Wires&
The Second hole
The holeTop
Black EPP White EPP and White EPO is the same/
Recommend wrapping tape to the connector
if you have no connector locker
P13

Launch Cart
Launch Cart is not must to everybody OPtions only
Good to enjoying rolling take off and beginner
not included by kits ARF
()
</>
Front wheel
4 0 Hole.Φ
Rear wheel
3 0 Hole.Φ
Find out all the parts gluing the metal washers first
,
Φ40.
Φ30.
P14

EVA Cushion
What is this for ?
Use it as cushion if you found the locker become loose
P15

Suggestions
P16
Tail
Main Wing-
Chamfer edges of those carbon tubes
would be more smooth and convenience to deployment

Suggestions
P17
Tail Fuselage cover is possible protruded after gluing
if you found big gap between fuselage and tail boom
use hobby knife cut off few foam of the fuselage cover
-
Please ignore this page if no obvious gap
Good