Firesense 60351 User manual

VERNON ELECTRIC FIREPLACE
MODEL # 60351
CARE & USE GUIDE
Please read this manual before
installing and using your fireplace.
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN
ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF LIFE.

Thank you for purchasing a Fire Sense Electric Fireplace.
Important: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, fire hazard and
will void the warranty.
Read all instructions before using this appliance.
This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. If provided, use handles when moving this appliance. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3
feet from the front and sides of this appliance.
Caution: Extreme caution is necessary when any heater is used near children or
disabled persons. Never leave any heater unattended.
Always unplug this appliance when not in use.
Do not operate any heater with a damaged cord or plug or after the appliance
malfunctions, or has been dropped or damaged in any manner.
Any repairs to this appliance must be carried out by a qualified service person.
Under no circumstances should this appliance be modified. Parts having to be
removed for servicing must be replaced prior to operating this appliance again.
Do not use outdoors.
This appliance is not intended for use in bathrooms, laundry areas and similar indoor
locations. Never locate this appliance where it may fall into a bathtub or otherwise
become exposed to water.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like.
Arrange cord away from traffic areas and where it will not be tripped over.
To disconnect this appliance, turn controls to the off position, them remove the plug
from the outlet.
Connect to properly grounded outlets only.
This appliance, when installed must be electrically grounded in accordance with local
codes, and the National Electrical Code, ANSI/NFPA No. 70.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock, fire or damage the appliance.
To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use
on soft surfaces, like a bed, where openings may become blocked.
This appliance has hot and arching or sparking parts inside. Do not use it in areas
where gasoline, paint or flammable liquids are used or stored. This appliance should
not be used as a drying rack for clothing, nor should Christmas stockings or
decorations be hung on or near it.
INSTALLATION INSTRUCTIONS – GENERAL
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.

A 15 Amp, 110 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this
appliance. The fireplace must be on a dedicated circuit as other appliances on the same
circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in opera-
tion. The unit comes standard with a 6.5 ft long 3 wire cord, exiting out the back of the
fireplace. Plan the installation to avoid the use of an extension cord. If an extension cord
must be used, it must be a minimum 14 gauge, 3 wire with grounding type plug and
connector and rated not less than 2025 watts. The extension cord shall not be more than
20 ft in length.
ELECTRICAL CONNECTION
SPECIFICATIONS
Dimensions LxWxH
Net Weight
Voltage
Frequency
Watts
Heater Rating
10"x6.35"x21.67"
28.7 lbs
110-120V
60 Hz
1350 W
4600 BTU
WARNING: Electrical outlet wiring must comply with local building codes and other
applicable regulations to reduce the risk of fire, electrical shock and injury to persons.
WARNING: Do not use this fireplace if any part of it has become wet. Immediately call a
qualified service technician to inspect the fireplace and replace any part of the electrical
system which has been wet.
17.
18.
Use this appliance only as described in this manual. Any other use not recommended
by the manufacturer may cause fire, electric shock or injury to persons.
Avoid the use of an extension cord because the extension cord may overheat and
cause a risk of fire. However, if you have to use an extension cord, the cord shall be
14 gauge minimum size and rated not less that 2025 watts. The extension cord must
be a three wire cord with grounding type plug and cord connector. The extension
cord shall not be more than 20 feet in length.

CLEANING
Turn heater OFF and unplug from outlet. Use a vacuum or duster to keep heat
and vent area clean from dust and dirt. The exterior of the stove should be
cleaned with a damp cloth or duster. Do not use abrasive cleaners, liquid sprays,
or any other cleaner that may scratch the surface.

FOR YOUR SAFETY
Service must be performed by a qualified service agency.
REPLACING THE LIGHT BULBS
This fireplace uses 2 clear 110 Volt, 40 Watt, E-12 socket base light bulbs (small base,
chandelier candle type bulbs). The access plate is located on the back of the unit. For
convenience, if one of the light bulbs burns out, it may be easier to replace both of the
light bulbs at the same time.
WARNING: Do not exceed 40 Watts per bulb. Use of higher rated bulbs may result in a
fire, causing property damage, personal injury or loss of life.
Turn off the power to the unit, and unplug it from the electrical outlet.
Let the fireplace cool if it has been operating.
Turn the fireplace so you are facing the back of the fireplace.
Look for the access plate with the gold printing on it.
Remove the 3 screws holding the access plate in position. Once you have removed
the 3 screws, lift the access plate so the 2 positioning tabs come free of their slots.
Once you have removed the access plate you can see and access the two 40 watt
chandelier bulbs.
Remove each light bulb by unscrewing them out of the bases, turning them
counterclockwise. You can use one hand to hold the light socket in place, if required.
Install the new light bulbs by turning each light bulb into the base clockwise. You can
use one hand to hold the light socket in place, if required.
Replace the access plate by inserting the 2 tabs, pushing the plate up against the
fireplace back, and inserting the 3 screws.
Turn the fireplace back so you are facing the front of the fireplace.
Plug the fireplace back into the electrical outlet and turn the power on and enjoy the
flame effect.
SERVICE INSTRUCTIONS
SERVICE INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
On/Off
to the unit
Your fireplace has the following functions:
Please note: Both the low heat
and the high heat switches must
be in the on position to achieve
high heat.
High heat
1350 watts
Low heat
700 watts
Power
700
1350