Firesense BLT-999W-2 User manual

60948
Meijer.com
OWNER'S MANUAL
Wall Mount Electric Fireplace
BLT-999W-2
Item #
-IMPORTANT NOTICE-'
-Do NOT return to place of purchase
For customer service and warranty issues
contact our Toll Free Hotline at:
(866)-985-7877 OR
Email: [email protected]
Hotline hours: Mon. -Fri. 9:00 am -6:00 pm (EST)

Meijer.com
E1
Read these instructions completely before
beginning installation. Failure to follow
them could cause a heater malfunction
resulting
in serious injury and/or property
damage.
~ .... WARNING: All electric heaters have
hot and arcing or sparking parts inside.
Do not use it in areas where gasoline,
paint
or flammable liquids are present.
..... WARNING: This electric fireplace is
tested and listed for use only with the
optional accessories listed in these
instructions.
Use of optional
accessories
not specifically tested for
this electric fireplace could void the
heater warranty and/or result in a
safety hazard.
This electric fireplace meets the
construction and safety standards of H.U.D.
for application in manufactured homes when
installed according to these instructions.

Meijer.com
Important Safely Instructions..................................................... 4
Llst1ng Approvals ..................................................................... 7
Product Dimensions ................................................................. 8
Locating Fireplace .................................................................. 9
Unpocklng and Test1ng Fireplace............................................. 10
Grounding Instrucflons............................................................ 10
Installation ............................................................................ 11
Finishing Checklist.................................................................. 13
Operating InstrucTIons ............................................................ 13
Maintenance........................................................................ 15
Replacing the Bulbs .................................................................. 16
Troubleshooting.................................................................... 18
Warranly ............................................................................... 19

from the top,front and
sides of the heater.
Meijer.com

from top,front and sides of heater.
Meijer.com

Meijer.com
_6 ____________________________________________________ ___
IMPORTANT SAFETY INSTRUCTIONS
111 Do not insert or allow foreign objects to enteranyventilation
or exhaust opening as this may cause an electric shock or fire
or damage the heater.
121 To prevent possible fire, do not block air intakes in any
manner. Do not use on softsurfaces, like a bed, where
openings maybecome blocked.
131 The electric fireplace has hot and arcing or sparking parts
inside. Do not use it in areas where gasoline, paint
or
flammable liquids are used or stored.
141 Use this electric fireplace only as described in this manual.
Any other use not recommended by the manufacturer may
cause fire, electric shock
or injury to persons.
151 Avoid the use of an extension cord because the extension
cord may overheat and cause a risk
of fire. However, if you
have to use an extension cord, the cord should be No. 14AWG
minimum size and rated not less than 1875
WAITS.
161 Always use properly grounded fused and polarized outlets.
171 Always use ground fault protection where required by
electrical codes.
181 Always disconnect power before performing any cleaning,
maintenance
or relocation of heater.
191 To prevent a possible fire, do not bum wood or other materials
in this electric fireplace.
201 To prevent electric shock or fire, always hire a certified
electrician should new circuits
or outlets be required.
211 When transporting or storing this electric fireplace, keep in a
dry place free from excessive vibration and store as to avoid
damage.
SAVE THESE INSTRUCTIONS!

60948
Meijer.com
LISTING APPRO VALS
This heater has been tested in accordance with the CSAStandards for
fixed and location-<ledicaled electric room heaters
in the Uniled States
and Canada. Ifyou need assistance during installation, please contact
your local dealer.
Model Number:
Description:
Voltage:
Watts:
Amps:
Length:
Height:
Depth:
Item #
wan Mount Electric Fireplace
120V AC
MAX 1400W
1SAmp Grounded Circuit
29.6"
'9.78"
6.35"
Note: This healer
must be
electrically wired
and grounded
in
accordance with
local codes
or, in
the absence of
local codes, with
National Electric
CodeANSl/NFPA
70-latest edition
orthe Canadian
Electric Code,
CSAC22.1 as
appropriate.
7

Meijer.com
PRODUCT DMENSIONS
TOP VIEW
HeatEl' Vents
0J0 Not Cbver)
29,6-
r------------------------------~
o 0
o 0
o 0
o 0 -----T
o
o
o
o
o
• 0
<co
~o
0::
~o
o
o
o
o
o
~~~ ----.l
FRONT VIEW
BOTTOM VIEW
IDIII IIIIIIIIIIIIIII
I Cl
. ,===1· =======,·1 .
D
SIDE VIEW
Mounting £kIr
Mounting holes
BACK VIEW
Figure 1
Fireplace Dimensions

front and sides of heater.
Meijer.com
LOCATING FIREPLACE
WARNING: Due to high temperatures,this electric fireplace should be located out
of traffic. Keep combustible materials such as furniture, pillows, bedding, papers,
clothes and curtains at least 3 feet (O.9m) from top,
WARNING: Never locatethis electric fireplace where it may fall into a bathtub or
other water container.
CAUTION: Do not expose the electric fireplace to the elements (such as rain, etc.)
CAUTION: Wear gloves and safety glasses for protection during installation and
maintence.
WARNING: To prevent contact with sagging or loose Insulation, the electric
fireplace
must not be Installed against vapor barrier or exposed Insulation.
Localized overheating could occur and a fire could result.

Meijer.com
Carefully remove the unit from the box. Prior to installing
the unit, test to make sure the unit operates properly.
To do
this, plug the unit's power supply cord into a conveniently
located 120-Volt grounded outlet.
GROUNDING INSTRUCTIONS
This insert is for use on 120 Volts. The cord has a plug as
shown in (A)
of Figure 3 given below. An adapter as shown
in (C) is available for connecting three-blade grounding-
type plugs to two-slot receptacles. The green grounding
plug extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet
box. The adapter should not be used
if a three-slot
grounded receptacle
is available.
To disconnect heater, turn controls to off, then remove
plug from outlet.
\ \ ~
GROUNDING PIN
NOT ALLOWED
IN CANADA
(2) , J~
• METAL SCREW'"
(Q)
'---------"-~COVER OF GROUNDED (i})
(A) OUTLET BOX (B)
~ ADAPTER
GROUNDING
(C) MEANS
Figure 2
Grounding Methods

Meijer.com
~
~
~ WARNING: RISK OF FIRE! The powercord must not be pinched or against asharp
edge. Secure cord to avoid tripping or snagging to reduce risk of fire, electric shock
or personal injury. Do not run cord undercarpeting. Do not covercord with throw
rugs, runned or the like. Arrange cord away from traffic area and where it will not
betripped over.
J
.. WARNING: RISKOF FIRE! To prevent a possible fire, do not blockair intake or
exhaust in any manner. Do not use on soft surfaces where openings may become
blocked.
J
.. WARNING: RISK OF FIRE! Do not blow orplace insulation against the fireplace.
J
.. WARNING:This electric fireplace is tested and listed for use onlywith the
approved optional accessories. Use ofoptional accessories not specifically tested
for this electric fireplace could void the heater warranty and/or result in a safety
hazard.
~
II. WARNING: Ifthe information in these instructions is notfollowed exactly, afire or
explosion
may result causing propertydamage, personal Injuryordeath. Do not
store or
use gasoline or otherflammable vapors in thevicinity ofthis or any other
heater.

Meijer.com
_lillcle vI_
This fireplace must be
mounted on a wall with
a height above the floor
between O.5M (1.64
Feet) and 2.5M (8.2
Feet).
WARNING: Heater vents (see
Figure 1, page 8)
on this
electric fireplace cannot, in
any way,
be covered as it may
create a fire hazard.
Due to the manydifferent materials used on different walls, it is highly
recommended that you consult yourlocal hardware store to determine
what type
of mounting saews are needed before you install this
fireplace onto the wall.

Meijer.com
FINISHING CHECKLIST
> Powersupply service must be completed prior to finishing to avoid
reconstruction.
> Heatervents and air openings cannot be covered in any circumstances.
OPERATING INSTRUCTIONS
Once the unit has been properly connected to a grounded
electrical outlet, it is ready to operate.
Note: Ensure the house circuit breakers for the power
supply are turned on.
Main Power Switch:
The Main Power Switch is located on the right side of the unit.
Figure 4 illustrates the location of the switch. The "I" indicates
ON and "0" indicates OFF. Push the switch to "I" to tum on the
unit and the flame effect. The red LED Indicatorwill be turned on.
.IEO·
•
iii g CJ
(side view)
Power (on/off)
Figure 4
Main Power Switch

five
Meijer.com
OPERATING INSTRUCTIONS
The manual controls are located on the left side of thefireplace.
You nave tl'le following controls:
OPERATING BY REMOTE CONTROL
11 Plug in your electric fireplace.
2J Make sure the unit's Main Power ON/OFF
Switch is at the ON position! The remote
control will NOT work if the Main Power
Switch is at the OFF position.
31 When operating the remote control, it
must be pointed towards the front of the
unit.
4/ The ON/OFF button atthe below right ofthe
remote is the main ON/OFF power button
(Figure
5). Pressing this button activates
the power
to the unit. I
51 To activate the heater, press the I
button. Press and release the
button to cycle through LO, HI and
OFF.
6/ To adjust the flame height and ember bed
brightness, press the ~ b ~ or
.. t) •buttons. To increase the flame
height sIJd ember bed brightness, press
the" 0 "button, to decrease the
flame he1ght and ember bed brightness,
press the" 0 • button. There are
levels of (iame af feets.
71 To tum off the fireplace, press the
ON/OFF button once. NOTICE: This
remote control must remain within 8
meters or26 feet
of the fireplace to be
effective.
1. PowerONlOFF: Powertotheunit
2. Flame brightness controls: Allows you to adjust
the lIame
to suityour mood. Press /) to Increase
lIame brightnessand b
to dec~ flillme
brightness. You must P~ the9button several
times to see the
full flame effect
3. Lowheat 700watts
4. High heat 1400watts
Please note: The heater touchpilld control must be
touched 2times toachleve
hIgh heat.
s. HNterTlmer: Allows yoo to II!iIYe yoor hem!r
on whlleyoosleep with
In lutornatk:lImerfor shut
off. You an Htyaur hl!ltl!rto be on for 1/2 hour
Increments
mrdng M. 1/2 hour up to. maximum
of 7-1/2 hours -press ono:efor eI!Ich 1/2hour
Increment.
A~r yau IeICh 7·112 hoI.n 1he next
press will shut offtlM= feltu~
Note: Make sure your
batteries are fully
charged and Installed
correctly In your remoiB
control.
Figure 5
Remote Control For
Electric Fireplace

Meijer.com
iI1
I M!~ I ~ 11::1 ~ r!~ ~ [ej::l
~
~
Preparation for Maintenance
WARNING: Always disconnect the power and allow the
electric fireplace
to cool completely before performing any
cleaning, maintenance
or relocation of this electric fireplace.
Turn all controls
to OFF and remove plug from outlet or turn
off the house circuit breaker to electric fireplace receptacle.
Most halogen light bulbs are rated to last approximately 1800 hours.
Like all light bulbs, halogen bulbs require periodic replacement. When
the bulbs in your unit have burned out you will notice one or more of
following:
Common Observed Problems:
• There is no flame
• Flame
is dim or dark in certain areas
• Flame
is not moving or glowing
•
Ember bed is dim or dark in certain areas
Your fireplace unit must be opened in order to replace the light
bulbs. To reduce the number of times you need to open the unit,
replace all bulbs at the same time if they are close to the end oftheir
rated life.
~
~ARNING: Do not install replacement bulbs that exceed
specified maximum watts.
~
~WARNING: The halogen light bulbs in your unit can become
extremely hot. Allow
at least 10 minutes between turning off
the heater and removing the light bulbs to avoid accidental
burns.

Meijer.com
REPLACING THE LIGHT BULBS
This fireplace uses 2 clear 110 Voll, 40 Watt, E-12 socket base light bulbs (small base,
chandelier candle type bulbs). The access plate is located on thebollDmof the unit. For
convenience, if one of the light bulbs bums out, it may be easier to replace both of the
light bulbs at the same time.
WARNING: Do notexceed 40 Watts per bulb. Use
of higher rated bulbs may result in a
fire, causing property damage, personal injury or loss of life.
Bottom view Bottom view
I FIG. I I FIG. I
I. Tum off the power to the unit, and unplug it from the electrical outlet.
2. Let the fireplace cool if it has been operating.
3. Look for the access plate with the gold printing onthe bottom oIthe unil
4. Remove the 5 screws holding the access plate in position
(FIGI). Once you have
removed the 5 screws, lift the access plate so the 3 positioning tabs come free of
their slots. Once you have removed the access plate you can see and access the two
40 watt chandelier bulbs (FIG 2).

Meijer.com
;n
11 ~{elll:l ~::f.'1: leleJlI.leJ
~
~
WARNING: Turn off the fireplace completely and let cool
before servicing.
I .: -. t
••• : .. , • I
1. Inspect the bulbs
inside the flame
Dim or no flame
1. Bulb{s) are burnt out generation cylinder
drum and replace them
if necessary
Ember
bed is not
1. Bulb{s) are burnt out
1. Inspect the ember
glowing or dimming bed bulbs and replace
them if necessary
No warm air Is coming
1. Room temperature is
1. Set heater to a
out of the heater. Heat
higher than the heater highertemperature
doesn't tum
on when it setting {if it is set to LO
or
setting (MED or HI)
is set to Low setting.
MED)
1. Fireplace has 1. Unplug the unit.
Fireplace tums offand will overheated
and safety allow heater
to cool for
not tum on
device has caused the
10minutes. then plug it
thennal switch to back
in
disconnect 2. Reset house circuit
2. House circuit breaker breaker
has tripped
Fireplace will not come
1. Fireplace is not 1. Check plug and plug
on when switch is flipped plugged into an electrical it
in
to ON outlet 2. Unplug the unit.
2. Fireplace has allow heater
to cool for
overheated and safety 10minutes, then plug it
device
has caused the back
in
thennal switch to
disconnect
Remote control does not
1. Low batteries 1. Replace
AA baHaries
work
in remote control

Meijer.com
Distributed By:
Well Traveled Living
716 S8th Street
Amelia Island,
FL 32034
Toll Free: 866-WTL-SUPP
Web: www.wtliving.com
Email: [email protected]
1 YEAR LIMITED WARRANTY-Customers in the Continental US
All components are warranted for a period of 1 year after date of purchase by the original owner against defects in
materials and workmanship under normal use. This warranty does NOT cover normal wear and weathering, assembly
and/or maintenance OR use
in a commercial application. Light bulbs are not covered by this limited warranty and are the
sole responsibility
of the owner/purchaser. At well Traveled LMng's sole discretion, products under warranty will be
repaired and/or replaced at no charge to the customer. Any returns sent back to well Traveled Living must be sent via
prepaid freight and in the original retail packaging.
For warranty service contact Well Traveled Living at the address, phone numbers
or internet site and email listed in this
owner's manual. Be sure
to have your sales receipt, date of purchase and catalogue/model numbers available when
calling. All warrantyselVice will be coordinated by the
well Traveled Living's, Amelia Island, Florida service center.
This warranty is extended only to the original purchaser. Proof
of purchase will be required before warranty service is
rendered. The sales receipt is the only valid proof
of purchase. This warranty only covers failures due to defects in
materials or workmanship which occurduring normal use. Failures and/or damage which result from accident, negligence,
misuse, abuse, neglect, mishandling, alteration
or modification, failure to maintain, improper assembly or maintenance,
selVice
by unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT
covered.
-THERE ARE NO EXPRESS WARRANTIES EXCEPT AS USTEO ABOVE"~
-PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIr-
-FAILURE TO FOLLOWWARNINGS ANO OPERATIONAL INSTRUCTIONS CONTAINEO IN THIS MANUAL CAN
RESULT IN SEVERE PROPERTY DAMAGEANOIOR PERSONAL
INJURV-
IN NO EVENT WILL WELL TRAVELED LIVING, OR ITS OIRECTORS, OFFICERS OR AGENTS BE UABLE TO THE
PURCHASER OR
ANY THIRO PARTY, WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY
INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIOENTAL LOSS, COST, OR DAMAGE
ARISING OUT OF OR IN CONNECTION WITH THE
SALE, MAINTENANCE, USE, OR INABILITY TO USE THE
PRODUCT, EVEN IF
WELL TRAVELED UVING OR ITS DIRECTORS, OFFICERS OR AGENTS HAVE BEEN
ADVISED
OF THE POSSIBIUTY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR
DAMAGES
ARE FORESEEABLE. IN NO EVENT WILL WELL TRAVELED UVING, OR ITS OFFICERS, DIRECTORS,
OR AGENTS
BE LIABLE FOR ANY DIRECT LOSSES, COSTS OR DAMAGES THAT EXCEED THE PURCHASE
PRICE
OF THE PRODUCT.
SOME JURISDICTIONS DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.
This limited warranty gives you specific legal rights and you may also have other rights which vary fromjurisdiction
to
jurisdiction. The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not applyto this
limited warranty
or the sale of products covered by this limited warranty.
···IMPORTANT NOTICE···
-Do NOT return to place of purchase-
For customer service and warranty issues
contact our Customer Service Center at:
(866)-985-7877 OR
Email: [email protected]
Customer Service Hours: Mon.- Fri. 9:00 a.m. -6:00 p.m. (ESn
Fire Sense' and WellTraveled Uvinge are registered trademarks of WellTraveled Imports, Inc·. All assembly instruction presentations are the property of Well
Traveled Imports,
Inc.· and are protected by U.S. copyrights and trademarks. All rights reserved.