First Alert CO710 User manual

Other manuals for CO710

Table of contents

Other First Alert Carbon Monoxide Alarm manuals

First Alert

First Alert FCD2N User manual

First Alert

First Alert SCO5B Series User manual

First Alert

First Alert CO600A User manual

First Alert

First Alert ONELINK SCO500 User manual

First Alert

First Alert CO410 User manual

First Alert

First Alert FCD2N User manual

First Alert

First Alert CO410 User manual

First Alert

First Alert First Alert CO400 User manual

First Alert

First Alert CO605 User manual

First Alert

First Alert CO600 User manual

First Alert

First Alert GCO1B User manual

First Alert

First Alert Model GCO1 User manual

First Alert

First Alert FCD2DD User manual

First Alert

First Alert CO600B User manual

First Alert

First Alert FCD4 User manual

First Alert

First Alert SCO5 User manual

First Alert

First Alert KV-T29SN81 CO410 User manual

First Alert

First Alert CO5120BN User manual

First Alert

First Alert CO606A User manual

First Alert

First Alert MODEL FCD3N User manual

First Alert

First Alert FCD2BT User manual

First Alert

First Alert SCO5B User manual

First Alert

First Alert SCO1N User manual

First Alert

First Alert GCO1B User manual

Popular Carbon Monoxide Alarm manuals by other brands

Honeywell

Honeywell H450EN instruction manual

Honeywell

Honeywell SF350RVUL owner's manual

Poolguard

Poolguard DAPT-2 installation instructions

Ei Electronics

Ei Electronics Ei 261D Instruction leaflet

Bacharach

Bacharach Model 105 supplementary guide

Firex

Firex COZ-1 owner's manual

Costar

Costar 12RV-D owner's manual

FireAngel

FireAngel CO-9X user manual

Costar

Costar 12-24SIR owner's manual

Kidde

Kidde KN-COEG-3 (900-01 13) user manual

System Sensor

System Sensor CO1224T Installation and maintenance instructions

Deltronic Security

Deltronic Security CN-1231 owner's manual

GE Interlogix

GE Interlogix 240 COE - Carbon Monoxide Alarm installation instructions

Sygonix

Sygonix 2377794 operating instructions

Kidde

Kidde 8LLCO user guide

Convoy Tech

Convoy Tech CO311 user guide

nest

nest PROTECT user guide

Bosch

Bosch CRS-WLCD-TA869 quick guide

INSTALLATION

WHERE TO INSTALL CO ALARMS

RECOMMENDED PLACEMENT:

Smoke Alarm

One on every level and

in every bedroom

Carbon Monoxide Alarm

One on every level and

in every bedroom

Fire Extinguisher

One on every level, plus

kitchen and garage

HALLWAY BEDROOMBEDROOM

GARAGE

LIVING ROOM KITCHEN

BASEMENT

IN A SINGLE-LEVEL HOME:

• Install at least one CO alarm near or within each separate sleeping area.

• For added protection, install an additional CO alarm at least 20 feet (6 meters)

away from the furnace or fuel burning heatsource.

IN A MULTI-LEVEL HOME:

• Install at least one CO alarm near or within each separate sleeping area.

• For added protection, install at least one CO alarm on each level of the home. If you

have a basement, install that CO alarm at the top of the basement stairs.

• For added protection, install an additional CO alarm at least 20 feet (6 meters)

away from the furnace or fuel burning heat source.

IN A MOBILE HOME:

• Install CO alarms on inside walls ONLY. Uninsulated outside walls and roofs of

mobile homes often transfer heat and cold from outdoors.

The National Fire Protection Association (NFPA) recommends that a CO alarm should be centrally located

outside of each separate sleeping area in the immediate vicinity of the bedrooms. For added protection,

install additional CO alarms in each separate bedroom, and on every level of your home. If your bedroom

hallway is longer than 40 feet (12 meters), install a CO alarm at BOTH ends of the hallway.

TROUBLESHOOTING GUIDE

IF THE ALARM... PROBLEM... YOU SHOULD...

Horn sounds 3 “chirps” every minute.

MALFUNCTION SIGNAL. Based

on its Self Test diagnostics, the

unit has detected a malfunction.

The unit needs to be replaced.

CO alarms under warranty should

be returned to manufacturer

for replacement. See “Limited

Warranty” for details.

Horn sounds 5 “chirps” every minute. END OF LIFE SIGNAL.

CO alarm needs to be replaced. Immediately replace the CO alarm.

CO alarm goes back into alarm

4 minutes after you press

the Test/Silence button.

CO levels indicate a potentially

dangerous situation.

IF YOU ARE FEELING SYMPTOMS OF CO

POISONING, EVACUATE your home and

call 911 or the Fire Department. Refer to

“If The CO Alarm Sounds” for details.

CO alarm sounds frequently even

though no high levels of CO are

revealed in an investigation.

The CO alarm may be improperly

located. Refer to “Where to

Install CO Alarms” for details.

Relocate your alarm. If frequent alarms

continue, have home rechecked for

potential CO problems. You may be

experiencing an intermittent CO problem

If you have questions that cannot be answered by reading this manual, call the Customer Service Team at 1-800-323-9005

HOW YOUR CO ALARM WORKS

GENERAL INFORMATION

• CO alarm contains a sealed, non-replaceable battery. Once it reaches the end of its service

life, or after 10 years—whichever comes first—you must install a new CO alarm.

• High temperatures, low temperatures, high humidity, impact or dropping can adversely affect LCD displays.

A CO alarm measures the CO levels in the air. It will alarm if CO levels rise quickly (if the heat exchanger on your

furnace breaks, for example), or if CO is consistently present (a slow CO leak on a fuel-burning appliance).

This carbon monoxide alarm features a permanently installed sensor, digital display with blue backlight, and an 85 dB alarm

horn. It also has a silence feature to temporarily quiet the alarm horn. During standby, the temperature is displayed in degrees F.

THE PARTS OF

YOUR CO ALARM

1. Test button

2. Activation + deactivation

tab (back of unit).

3. Silence button

4. Alarm horn (behind cover):

85dB audible alarm for

test, alarm, and unit

malfunction warning.

5. Peak level button.

6. Digital display with

blue backlight.

1, 3, 5

UNDERSTANDING YOUR CO ALARM

Alarm Digital Display

First Activated Display glows and horn chirps

when alarm is first activated.

All segments are turned on

for a short time upon initial

power. Then the temperature

is displayed in degrees F.

Alarm Receiving

Battery Power Horn is silent. Temperature will be

displayed in degrees F.

During Testing

A single beep will be issued after

pressing and holding the test

button.Following the single beep, a

4 beep pattern will be issued twice.

Display glows and shows “tst”.

Several ppm CO levels are

also displayed and the alarm

level is shown increasing.

CO Alarm

Sensor has detected enough CO

to trigger an alarm. Blue backlight

glows and horn sounds loudly

(repeating 4 beeps, pause). See

“If Your CO Alarm Sounds” for

details. During an alarm, move

everyone to a source of fresh air.

DO NOT move the CO alarm!

“CO” alternating with the

ppm number, a full level,

and “EVACUATE”.

Co Alarm

Requires

Service

(Malfunction

Signal)

The horn sounds 3 “chirps”

every minute. CO alarm

needs to be replaced.

“Err” is displayed.

CO Alarm

End of Life

The horn sounds 5 chirps

every minute. CO alarm

needs to be replaced.

“End” is displayed.

USING THE PEAK CO MEMORY

The CO memory feature lets you check the highest level of CO recorded during an alarm.

NOTE: These bars will not appear when CO accumulation is low. The bars will be displayed

when unit is exposed for a longer time and CO accumulation is higher.

To Check CO

Memory 1. Press and release the test button until the peak CO level is displayed.

To Clear CO

Memory

1. Automatically resets after 24 hours.

2a. Press and release test button until blue backlight glows.

2b. Press and release test button to enter “clear mode”.

2c. Press and release test button quickly one more time to clear.

NOTE: Must press and release. Press and hold will run into “Test Mode”.

NOTE: The highest CO level will be saved for 24 hours. DO NOT clear the CO memory reading if you plan to call someone to

investigate a CO problem! Clear the CO memory reading only after the investigator has checked your home. If the investigator

will not arrive within the 24 hour time period before the unit automatically resets, be sure to write down the peak level.

WHERE CO ALARMS SHOULD NOT BE INSTALLED

DO NOT INSTALL THIS CO ALARM:

• In garages, kitchens, furnace rooms, or in any extremely dusty, dirty or greasy areas.

• Closer than 20 feet (6 meters) from a furnace or other fuel burning heat source, or fuel burning appliances like a water heater.

• Within 5 feet (1.5 meters) of any cooking appliance.

• In extremely humid areas. This alarm should be at least 10 feet (3 meters) from a bath or shower, sauna,

humidifier, vaporizer, dishwasher, laundry room, utility room or other source of high humidity.

• In areas where temperature is colder than 40˚ F (4.4˚ C) or hotter than 100˚ F (37.8˚ C). These areas include

unconditioned crawl spaces, unfinished attics, uninsulated or poorly insulated ceilings, porches, and garages.

• In turbulent air, like near ceiling fans, heat vents, air conditioners, fresh air returns, or

open windows. Blowing air may prevent CO from reaching the sensors.

• In direct sunlight.

HOW TO INSTALL YOUR CO ALARM

READ “WHERE TO INSTALL CO ALARMS” BEFORE STARTING.

Before you start installation, find the pair of self-adhesive labels included with this CO alarm. On each label

write in the phone number of your emergency responder (like 911) and a qualified appliance technician. Place one

label near the CO alarm, and the other label in the “fresh air” location you plan to go if the alarm sounds.

NOTE: Activate alarm prior to mounting.

1. Activating the Battery. Move the activation

switch to ON position. Utilize a small tool

to help activate switch if needed. Once unit

is activated, it cannot be turned off.

NOTE: Horn chirps, and all segments are

turned on for a short time upon activation.

2. Test the CO alarm. See “Weekly Testing”.

3. To Permanently Deactivate the Alarm. This

CO alarm contains a sealed, non-replaceable

battery. Once it reaches the end of its service

life, or after 10 years you must install a new CO

alarm. Deactivate the CO alarm by inserting a tool

below edge where shown and break tab. Then

slide activation switch to DEACTIVATE mode.

DEACTIVATE

HOW TO ACTIVATE ALARM:

1. TO ACTIVATEALARM, MOVE

SWITCH TO ON POSITION.

2. PRESS AND HOLD TEST

BUTTON TO ENSURE ALARM

IS ACTIVATED.

HOW TO DEACTIVATE ALARM:

TO DEACTIVATE BATTERY,

BREAK AWAY TAB AND

MOVE SWITCH TO DEACTIVATE

POSITION. ONCE DEACTIVATED,

THE ALARM CANNOT BE

REACTIVATED AND MUST BE

REPLACED.

3055574

WARNING

CARBON MONOXIDE CANNOT BE SEEN OR SMELLED BUT CAN KILL YOU.

IF ALARM SIGNAL SOUNDS:

1) OPERATE TEST / SILENCE BUTTON.

2) CALL YOUR EMERGENCY SERVICES (FIRE DEPARTMENT OR 911).

3) IMMEDIATELY MOVE TO FRESH AIR - OUTDOORS OR BY AN OPEN DOOR /WINDOW.

ALARM GUIDE:

FIVE “CHIRPS” PER MINUTE – END OF LIFE SIGNAL (10YEAR) – REPLACE ALARM

FOUR BEEPS – CO ALARM

THREE “CHIRPS” / MINUTE – MALFUNCTION – REPLACEALARM

MAINTENANCE, AND TESTING:

ALARM IS SEALED WITH NO SERVICEABLE PARTS. BATTERY IS NOT REPLACEABLE.

CONSTANT USE AT HIGH OR LOW TEMPERATURES OR HIGH HUMIDITY MAY REDUCE

BATTERY LIFE. TEST AFTER INSTALLATION, WEEKLY, AND AFTER CLEANING. GENTLY

VACUUM OR USE CLEAN COMPRESSED AIR TO REMOVE DUST. NEVER USE WATER,

CLEANER OR SOLVENT, SINCE THIS MAY DAMAGE THE UNIT.

MODEL NO. CO710

SINGLE STATION CO ALARM

TO ORDER REPLACEMENT USER’S MANUAL OR TO RETURN

ALARM BRK BRANDS, INC 1301 JOE BATTLE, EL PASO, TX 79936

USA. FOLLOW AND RETAIN USER’S MANUAL CUSTOMER SERVICE

TEAM: (800) 323-9005 WWW.BRKELECTRONICS.COM

WWW.FIRSTALERT.COM

RESPONSE TIME (MIN)

60 - 240

10 - 50

4 - 15

CO LEVEL (PPM)

150

400

IMPORTANT!

REFER TO USER’S MANUAL FOR MORE INFORMATION.

CARBON MONOXIDE SENSITIVITY

CONFORMS TO

UL STD 2034

MADE IN MEXICO

N04-3123-160836

Replace alarm 10 years after installation

Installed On

Replace By

NOTE: Once you deactivate this unit, it will not detect CO or alarm and cannot be reactivated.

4. This CO alarm can either be wall mounted or placed on a tabletop. If alarm is placed on a tabletop,

be sure the alarm is no more than 3 feet (0.9 meter) from the floor to minimize the risk of causing

permanent damage to the alarm in the event that it is accidentally knocked to the ground.

TO MOUNT ON THE WALL

Tools you will need: pencil, drill with 3/16” or 5mm drill bit, flathead screwdriver, hammer, mounting template.

1. Choose a location on the wall. Do not install the alarm closer than 4” (102 mm) from where the wall meets the ceiling.

2. Hold the mounting guide template against the wall, and make a mark inside each keyhole

where you will drill your mounting holes as shown in the diagram below.

3. Use a 3/16” (5 mm) drill bit to drill through the marks you made for the mounting holes.

4. Insert the plastic screw anchors into the mounting holes until they are flush

with the wall. If necessary, tap them gently with a hammer.

5. Insert the screws into the anchors until the screwhead is 1/8 inch (3 mm) away from the wall.

6. Slide the CO alarm onto the screws until you feel it click into place.

7. Test the CO alarm as described in “Weekly Testing.”

Mounting Guide Template

inches (66.68 mm)

IMPORTANT! PLEASE READ

CAREFULLY AND SAVE.

The warnings/limitations card and manual contains

important information about your carbon monoxide

(CO) alarm’s operation. If you are installing this

CO alarm for use by others, you must leave this

manual—or a copy of it—with the end user.

Reference product card for additional information.

USER’S MANUAL

CARBON MONOXIDE ALARM

10-YEAR SEALED BATTERY CARBON MONOXIDE

ALARM WITH DIGITAL TEMPERATURE DISPLAY

Printed in Mexico

M08-0534-160326-US_RevB L01/18

Model CO710

CONFORMS TO UL STD 2034

INTRODUCTION

BASIC SAFETY INFORMATION

• Dangers, Warnings, and Cautions alert you to important operating instructions or

to potentially hazardous situations. Pay special attention to these items.

• This CO alarm is approved for use in single-family residences. It is NOT designed for marine or RV use.

• This carbon monoxide alarm is designed to detect carbon monoxide gas from ANY source of combustion.

This CO alarm is not designed to detect smoke, fire, or any other gas. It will only indicate the presence

of carbon monoxide gas at the sensor. Carbon monoxide gas may be present in other areas.

• This unit will not operate without battery power. The CO alarm cannot

work until you activate the battery power pack.

• NEVER ignore any alarm. See “If Your CO Alarm Sounds” for more information on how

to respond to an alarm. Failure to respond can result in injury or death.

• The silence features are for your convenience only and will not correct a problem.

See “Using the silence features” for details. Always check your home for a potential

problem after any alarm. Failure to do so can result in injury or death.

• Test this CO alarm once a week. If the alarm ever fails to test correctly, have it replaced

immediately! If the alarm is not working properly, it cannot alert you to a problem.

• This product is intended for use in ordinary indoor locations of family living units. It is not

designed to measure CO levels in compliance with Occupational Safety and Health Administration

(OSHA) commercial or industrial standards. Individuals with medical conditions that may make

them more sensitive to carbon monoxide may consider using warning devices which provide

audible and visual signals for carbon monoxide concentrations under 30 ppm. For additional

information on carbon monoxide and your medical condition contact your physician.

is a subsidiary of Newell Brands Inc. (NYSE:NWL) •3901 Liberty Street, Aurora, IL 60504-8122 •

Customer Service Team: (800) 323-9005 •www.firstalert.com •www.brkelectronics.com

Installed on Replace by