Firstech, LLC. FTI-FDK1 User manual

FTI-FDK1 Type 1B - Vehicle Coverage & Preparation Notes
Make Model Year Install I/O Changes
DL-FM2
Ford
Lincoln
Lincoln
Lincoln
Mercury
Mustang
MKS
MKZ
MKZ Hybrid
Sable
2010-14
2009-12
2010-12
2010-12
2008-09
Type 1
Type 1
Type 1
Type 1
Type 1
CAN Lights RAP Trunk
Green White/BluePark / Auto
OBD-II
OBD-II
OBD-II
OBD-II
OBD-II
B
B
B
B
B
CM-900
CM-900S/900AS
CM7X00
CM7000/7200 Cut loop for A/T
CM900AS/900S Jumper
SUPPORT - 1(888) 820-3690, EXT. 203
DEREK ZOOLANDER
Est. 2001
CENTER KIDS
WHO CAN’T READ GOOD
A
N
D
W
H
O
W
A
N
N
A
L
E
A
R
N
T
O
D
O
O
T
H
E
R
S
T
U
F
F
G
O
O
D
T
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
for
Hey! Read this stuff before you start the installation...
Firmware:
Covered vehicles use BLADE-AL(DL)-FM2, flash module and update the controller firmware before installing.
Door Locks:
With alarm: Door locks require three wire connections (1-unlock, 2-lock) and two (2) diodes isolating the lock wires.
Mustang: Lock/Arm wire color, yellow/gray (pin #9/26 at BCM)
Without alarm: Door locks require two wire connections and no diodes.
Auto-lights: If vehicle is equipped with auto-light feature, refer to the diagram below for required connections.
Auto-light: violet/green (pin #4)
Light-off: white/violet (pin #6)
Okay, now get to work...
E
10
14
9
6
87a
87
30
STATUS
+12V
white/violet
violet/green

A B C D E
N
I
C
K
DL-FM3 TX loop, not used in this install type, do not cut.
Jumper for vehicles that are not equipped with immobilizer, do not connect unless vehicle is confirmed
not equipped. If vehicle is not equipped, connect before programming to skip immobilizer learn.
NO ALARM: Door lock connection at BCM (pin #17, blue/green, 26-pin connector)
WITH ALARM: Door lock/arm connections at BCM (pin #6, yellow/green, pin #18, violet/green,
26-pin connector), diode isolate the factory wires (cathode toward CM) and connect to CM output 1
2
3
SUPPORT - 1(888) 820-3690, EXT. 203
FTI-FDK1 Type 1B
Module Programming Procedure
Step 1 - Key #1 in activate IGN, if LED goes blue, you’re done
if LED goes red, wait until flashes blue then key off/on
Step 2 - If LED goes blue, you’re done, if red, insert key #2
and activate IGN, when LED is red, remove key, press
module button, and remote start vehicle, blue/done.
**See BLADE guide for more detailed instructions
FTI-FDK1 Type 1B - Installation Notes & Wiring Diagram
1
2
3
PWR
BLADE
Lock
1
16
RAP
LOCK/UNLOCK
TRUNK RELEASE
31
14171862
1
46
167
813
C
K
K
OR
OBD-II Connector
Ignition switch
BCM
blue/black
blue
Gray
Gray
green/violet
white/black
white/red
DRIVER DOOR PIN
(+) PARKING LIGHTS green/white
violet/white
blue/green
violet/gray
violet/green
yellow/green
LED Programming Error Codes
Module LED flashing RED during programming
1x - CAN error, check wiring
2x - VIN error, check CAN wiring
3x - Wrong firmware, confirm firmware flashed
4x - VIN error, vehicle not identified, contact support
5x - Immobilizer learn error, check RX/TX wiring
6x - KLON error, check RX/TX wiring, confirm pin positions
7x - KLON error, process failed, reset module and start over
8x - Encryption error, confirm key encryption, 80 bit detected
9x - Key in cylinder, remove and proceed
I
N