Directed Electronics XK01-AMDL User manual

SEE WIRE CONNECTION GUIDE FOR DETAILED INFORMATION REGARDING WIRE FUNCTIONALITY
Section A
Red
Orange
Green
Blue
Violet
Black
Violet/White
Pink
Pink/White
Chassis Ground
(+)12 Volt Constant
Trunk or Disarm Input (See Wire Connection Guide)
Aux1 (See Wire Guide)
Aux2(Wire acts as Input or Output depending on vehicle type. See Wire Guide)
Door Sense Trigger
Unlock
Programming Button
Lock
Brown
Ground When Running
LED
10 PIN HARNESS
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
IN/OUT
DATA
INPUT
OUTPUT
(-)
(+)
(-)
(-)
(-)
(-)
(+/-)
(-)
(-)
Data (see FIG 2)
Fig. 2: DATA WIRE
CONNECTION
Data Wire Connects to OBDII PIN 2
Section B
Upgradeable Vehicle Interface
Module Door locks/
Data Override
GM Passlock 2/GM Passkey 3
OEM Alarm
REMOTE
RCS
SYSTEM
WIRE GUIDE: CONNECTIONS
30
86 85
87
To Pink/White Wire
RELAY WIRING FOR WINDOWS ROLL-UP OPTION
To Brown Vehicle Accessory Wire
12 Volts
Fig. 1: TYPE 4 ONLY
LEGEND: RCS = Remote Control System N/C = No Connection N/A = Not Applicable W2W= analogue wire to wire D2D= data 2 data
(-)
/(+)
(-)
(-)
Input
Input
Input
Input
Input
Data
I/O
STATUS
WIRE
COLOR
Brown
Green
Blue
Violet/
White
Violet
Pink/
White
Pink
Orange
Red
Black (-)
(+)
SPECIFIC WIRE CONNECTION LOCATION
Constant (+) 12 Volt Source
Chassis Ground
Connect
Location
RCS
Vehicle
Vehicle
Vehicle
(-)
ACTIVATION and/or FUNCTIONALITY
-Locks All Doors
-Window Roll-Up Feature: Activated with 2ND press of aftermarket remote
(See User Settings, MODE 5)
Unlocks All Doors (See User Setting, MODE1)
RCS
RCS
Power Source
Ground Source
Data Commands from Module to Vehicle
PIN
1
2
3
4
5
6
7
8
9
10
Ground When Running Output of Remote Starter
Ground When Running Output of Remote Starter
D2D
w2w
10 PIN HARNESS
Lock Output wire
Unlock Output wire
Door Sense Trigger Input wire
Detects Door status (Open/Close) via data bus:
then converts to an analogue output (-)
Output (-) RCS
Input
Input
(-)
(-)
RCS
RCS
D2D = Optional use of 4 Pin Data to Data (D2D) cable will replace the analogue wire (w2w) connection
Connect to Vehicle’s Brown Accessory Wire
AUX 2 Output
N/C
Output
Input
N/C
(-)
(-)
N/C
Vehicle
RCS
N/C
Window Roll-Up (Relay Required, See Fig. 1)
1sec. (-) Pulse Left Sliding Door Open/Close
(See User Settings, MODE 3)
N/C
w2w
D2D
w2w
D2D
w2w
Input
Input
Input
(+/-)
(-)
(-)
Vehicle
RCS
RCS
Connect to Domelight (2 Door Vehicle N/A)
AUX 1 Output
AUX 1 Output
Domelight = Rear Door Detection
Opens Fuel Door
1 sec. (-) Pulse Right Sliding Door Open/Close
(See User Settings, MODE 2)
(See User Settings, MODE 2)
Disarm Output
Trunk Release Output
Connect if vehicle does not disarm upon remote start
Trunk Release
VEHICLE
TYPE
1to4
5to7
OEM Security Arm/ Disarm + Immobilizer Bypass + Defrost + Heated Seats at 32ºF (0ºC)
OEM Security Arm/Disarm + Defrost + Heated Seats at 32ºF (0ºC)
1to5
All Types
Input
(-) RCS
On Board Diagnostic Connector (OBDII) PIN 2
(See Fig.2)
All Types
Type 4
Type 7
1,2,3,5,6
D2D
w2w
w2w
D2D
w2w
N/C
1&4
Type 2
Type 7
1,4&5
2,3,6 & 7
All Types
All Types
All Types
3,5&6 N/C N/C N/C
N/CN/C
N/C
Lock Output wire
RCS
(-)
Input
D2D
w2w
6to7
Locks All Doors
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
1700G1
Description:
Functions:
American Door Lock Interface & GM Immobilizer Override
Lock/Unlock, Driver's Priority Unlock, Trunk/Hatch, Sliding Door Left & Right , OEM Security Alarm Arm/Disarm, Data to Analogue
Door Trigger Output (-) Override GM Passkey3 Transponder Immobilizer & Passlock 2 Immobilizer via data busGM ONLY:
Installation
Manual
(1\3 Pages)
AMERICAN DOOR LOCK INTERFACE
& GM IMMOBILIZER OVERRIDE XK01-AMDL
IMPORTANT! Please read this installation guide thoroughly before installing the 1700G1. Use only a high quality digital multi-meter for testing. This product connects to the vehicle's low
voltage signal wire and improper installation or testing can result in damage to the vehicle. Never use a test light or logic probe to test wires in this vehicle!

1) Plug the 10 PIN harness into the module. LED will turn ON solid.
2) Turn the ignition key to the ON position. LED will turn off then it will begin a flash pattern that matches the vehicle type selection.
(The default vehicle type selection is Type 1.)
*If the module has already been programmed to the vehicle, LED will flash 4 times. If this happens, skip to step 4.
3) To change the vehicle type, press and release the program button until LED flash pattern matches the selected vehicle type.
LED flash pattern will match the Vehicle Type selected. Example: 1 flash = Type 1, 2 flashes = Type 2 and so on.
4) To save the vehicle type selection, press and hold the program button until the LED flashes rapidly. The module will then exit the
programming. The module is now programmed.*If LED comes on solid, turn the key to start the engine.
The interface kit is designed to operate on any one of 7 possible vehicle types. Once the 10 pin harness wires have been connected,
the next step is to program the interface module to operate on the appropriate vehicle type. *Refer to the Vehicle Type Chart..
VEHICLE TYPE PROGRAMMING:
MODE 1 =
MODE 3 = *OPTION 1
MODE 4 = *OPTION 1
MODE 5 = *OPTION 1
MODE 8 = *OPTION
: (aux2) Pink/White Wire Negative
: (aux2) Pink/White Wire Output
: Window Roll-Up OFF
1: N/A
*OPTION 1 1st Pulse Unlock All Doors:
MODE 2= *OPTION 1: (aux1) Pink Wire Negative
OPTION 2 1st Pulse Unlock Driver Door, 2nd Pulse Unlock All Doors:
OPTION 2: (aux1) Pink Wire Positive
OPTION 2
OPTION 2
OPTION 2
: (aux2) Pink/White Wire Positive
: (aux2) Pink/White Wire Input
: Window Roll-Up ON
OPTION 2: Reset Mode With Unlock Button
* = Default
INSTALLATION NOTES:
!
!
The module will detect all door triggers through the data line. When the module detects an open door through the data line, it will send a negative pulse (-)
trigger on the PURPLE/WHITE wire (Door trigger output).
For Type 1 and 4 vehicles, the front doors and rear hatch ONLY are monitored via the data line. The rear doors are triggered separately and are not
monitored via the data line. You need to use the PINK wire to detect rear doors (Option Programming Mode 2). These wires are usually found at the BCM
(Body Control Module) or at the rear doors.
Section C
Section D
VEHICLE TYPE CHART:
USER SETTINGS - OPTIONAL PROGRAMMING:
USER MODES ARE IDENTIFIED BY A SLOW LED FLASH PATTERN. 1 SLOW FLASH=MODE1, 2 SLOW FLASHES=MODE 2 ETC.
1) Turn the ignition key to the OFF position.
2) To access USER MODES: Press & Hold the programming button until the LED flashes rapidly, then release.
3) To select a MODE: Press & Release the program button until the slow LED flash pattern matches the required MODE selection:
Ex: 1 SLOW flash = MODE 1, 2 SLOW flashes = MODE 2.
4) To change the MODE OPTION: Press the LOCK or UNLOCK button on the aftermarket transmitter.
LED will confirm selection of OPTION 1 with one fast flash or OPTION 2 with two fast flashes and so on.
5) To Save & Exit : Push & Hold the programming button until LED flashes once.
Section E
1700G1
Installation
Manual
(2\3 Pages)
AMERICAN DOOR LOCK INTERFACE
& GM IMMOBILIZER OVERRIDE XK01-AMDL
VEHICLES 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 VEHICLES 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998
Le Sabre 222222 Caravan 7777
Park Avenue 333333333 Grand Caravan 7777
Rainier 1111
Ultra 33333333 Envoy 111111
Sierra 1500, 2500, 3500 4** 4444
CTS 22222 Yukon Denali 4444
DeVille 322222222
Escalade 4444 H2 44444
Seville SLS 333333222
Seville STS 333333222 Ascender 11111
SRX 222
Grand Cherokee 555555
Avalanche 4444 Grand Cherokee Ltd 555555
*Impala LS *2*2*2*2*2*2Liberty 777
*Monte Carlo *2*2*2*2*2*2
Silverado 4** 4444 (with factory remote only) *Alero *2*2*2*2*2*2
SSR 111 Aurora 222
Suburban 4444 Bravada 111
Tahoe 4444
TrailBlazer 11111 Bonneville 222222
CHRYSLER (with factory remote only) *Grand Am *2*2*2*2*2
Pacifica 6666
Town & Country 7777 9-7X 11
JEEP
OLDSMOBILE
PONTIAC
SAAB
*In some cases the AMDL may only bypass the Passlock II via data. Once programmed, test the door lock inputs to determine if the AMDL will activate these functions via DATA
(multiplexed). If there is no activation, then the door lock system is resistance based and will need to be controlled via analog.
**AMDL can be used only if PIN#2 (Violet Wire) is found at the ODBII connector in vehicle.
BUICK
CADILLAC
CHEVROLET
DODGE
GMC
HUMMER
ISUZU

1700G1
Description: American Door Lock Interface & GM Immobilizer Override
Installation
Manual
(3\3 Pages)
AMERICAN DOOR LOCK INTERFACE
& GM IMMOBILIZER OVERRIDE XK01-AMDL
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security accessory product, Directed Electronics. (hereinafter "DIRECTED") promises to the
original purchaser, to repair or replace (at DIRECTED's election) with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the "Part"), which proves to
be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer in the United States; and
the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer's name, address, telephone
number, the authorized licensed dealer's name, date of purchase and complete product and Part description.
This warranty is non-transferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or if the Part has been damaged by accident,
abuse, unreasonable use, neglect, water, theft, improper service, installation or other causes not arising out of defect in materials or construction. This warranty is automatically void if any
Part has had the serial number defaced, altered, or removed. This warranty is automatically void if the Part has had Repair Service performed by anyone other than the Directed Repair
Department. This warranty does not cover damage to any Part caused by installation or removal of the Part or any system related thereto. This warranty does not cover labor costs for the
removal or reinstallation of the Part.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR
PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT PERMITTED BY LAW; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY
FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN
DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM
AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER,
INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC
OPPORTUNITY AND THE LIKE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights
and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or
obligation in connection with this Part.
LIMITED ONE-YEAR CONSUMER WARRANTY
1700G1
American Door Lock Interface
& GM Immobilizer Override XK01-AMDL
05
93207 05564
PRODUCT FEATURES
PRODUCT DESCRIPTION
1700G1 is a door lock & alarm data bus interface that can be used on a wide
selection of domestic and import vehicles. Best known for having the ability to
interface with more GM vehicles than any other product on the market. This
innovative kit is capable of interfacing with the latest communication networks
including CAN.
!
!
!
!
!
!
!
!
!
!
Wire to Wire compatible with any type of remote car starter (W2W)
Secure single-wire data transfer prevents analogue override activation
Compatible with manufacturer's anti-theft & content theft security systems
Maintains integrity of manufacturer's anti-theft immobilizer system
Maintains integrity of manufacturer's security and convenience functions
Compact design, easy to mount
No Key Required for operation (NKR)
Simple 2 step programming
All temperature operation
High security single-wire data transfer
PRIMARY PRODUCT FUNCTIONS
Lock/Unlock, Driver's door unlock, Trunk/Hatch, OEM Security Arm/Disarm,
Door trigger Output(-). Driver & passenger side sliding door control. *On select
GM vehicles with Passlock 2 or Passkey 3. 1700G1 can bypass the factory
immobilizer via data when remote starting. NKR - No Key Required.
© 2007 Directed Electronics. All rights reserved.