Fisher & Paykel ActiveSmart RS36A72J User manual

ActiveSmart™ Built-in refrigerator
RS36A72J and RS36A72U models
US CA
INSTALLATION INSTRUCTIONS
843157 A 06.15
www.fisherpaykel.com

1
FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY
WOODEN/PLASTER BOARD
WALL INSTALLATION
!1 PRODUCT PREPARATION
!3 ATTACH SIDE TRIMS
!0 CONNECT TO WATER AND ELECTRICAL SUPPLY
!4 ASSEMBLE DOOR PANEL SET
!5 HANGING ICE & WATER DOOR PANEL
!6 HANGING NON-WATER DISPENSING DOOR PANELS
!7 TOP TRIM AND HINGE END CAPS
!8 INSTALL WATER FILTER CARTRIDGE
@0 FINAL CHECKLIST
!9 ATTACH COVERS AND KICKSTRIPS
SOLID WALL
INSTALLATION
SPACER
INSTALLATION
!2 LEVEL YOUR PRODUCT
3 COMPONENTS LIST
4 PRODUCT AND CAVITY DIMENSIONS
6 MAXIMUM DISTANCE OF POWER CORD
5 CAVITY PREPARATION
7 CUSTOM DOOR PANEL DIMENSIONS
8 ATTACH SIDE TRIM BRACKETS
9 ATTACH ANTI-TIP BRACKET
2 BEFORE INSTALLATION
1 SAFETY AND WARNINGS
RS36A72J and RS36A72U
models

3
1SAFETY AND WARNINGS 2BEFORE INSTALLATION
Please follow the installation steps below to ensure your appliance is installed and
operatescorrectly.
Power
 To ensure that the appliance is not accidentally switched off, connect your refrigerator
toitsown isolating switch. Do not plug in any other appliance at this isolating switch.
 For power requirements, please refer to the information on the serial plate. This is located
atthe front right-hand side of the drawer when open.
 It is essential that the appliance is properly grounded (earthed).
 Connect the appliance to the electrical supply (115VAC, 60 Hz) with the fitted plug and lead.
 Follow the National Electrical Code and all local codes and ordinances when installing
thisproduct.
 Warning: Ground Fault Circuit Interrupters (GFCI) may trip during normal operation of
your refrigerator and interrupt the power supply. The use of a GFCI is not recommended
withthisproduct.
Location
 Your refrigerator should not be located in direct sunlight or next to any heat generating
appliance such as a cooktop, oven or dishwasher.
 Your product is fitted with front and rear rollers designed for moving the product
inforwards and backwards direction.
 Avoid moving the product in a sides ways direction as this may damage the rollers
orthefloor covering/surface.
Plumbing
 Your product must be installed by a qualified plumber or Fisher & Paykel Authorized
ServiceAgents as incorrect plumbing can lead to water leaks.
 Fisher&Paykel Appliances does not accept responsibility for damage (including water
damage) caused by faulty installation or plumbing.
Door panel set
 The standard appliance does not include a door panel set.
 When designing custom door panels, these are only available for non-Water dispensing models.
 To complete the integrated appliance for non-Water dispensing models the customer should
supply their own custom door panel set. All the hardware required to mount the door panel
sets to the refrigerator doors is supplied.
 Fisher & Paykel door panel sets are available (EZKleen stainless steel door panels, model
numbers: RD3672 and RD3672U), and can be purchased through your Fisher & Paykel
dealeror online at www.fisherpaykel.com (this service is available to selected markets only).
!WARNING!
Electric Shock Hazard
Read and follow the safety and warnings outlined in this installation
guide before operating this appliance.
Failure to do so can result in death, electric shock, fire or injury
topersons.
!WARNING!
Cut Hazard
Take care – panel edges are sharp. Failure to use caution could result in
injury or cuts.
!WARNING!
This appliance is top-heavy and must be secured to prevent the
possibility of tippingforward.
To ensure that the appliance is stable under all loading conditions, the
anti-tip bracket and fittings supplied must be installed according to the
following installation instructions by a professional installer.
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to
our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

4
3COMPONENTS LIST
French door
hanging bracket
(2)
Drawer hanging bracket
(1)
Side bracket
(10)
Side strap
(10)
M8 stud
(6)
Side cover
(10)
Top cover
(4)
M5 x 10 pan head
Phillips screw (10)
Door handle
(3)
M8 nut
(6)
M8 washer
(6)
Door panel fittings – Included with standard appliance.
Optional accessories – The standard appliance does not include a door panel set.
Fisher & Paykel door panel sets are available (EZKleen stainless steel door panels). To complete the integrated appliance for non-Water dispensing models the customer should supply their own
custom door panel set.
M5 x 25 pan head
socket screw
(12)
Non-Water dispensing French panel (1)
Ice & Water French panel (1)
Drawer panel (1)
Model number: RD3672U
Non-Water dispensing French panels (2)
Drawer panel (1)
Model number: RD3672
#8 x 16 mush
washerscrew (34)
M5 x 14 Mush Phillips SS
(34)

5
3COMPONENTS LIST
Kickstrip grille
(1)
Kickstrip filter
(1)
Water filter cartridge (1)
Part number: 839041
Product hardware – Included with standard appliance.
Ice & Water fittings – Included with standard appliance.
External display module (1)
(included with RS36A72U standard appliance)
Filter cartridge tool
(1)
Power cord clip
(1)
Anti-tip bracket fittings – Included with standard appliance.
Side trim bracket
(6)
Side trim
(2)
Collet locking key
(1)
¼”(6mm)
Compression nut
(1)
¼”(6mm)
Compression sleeve
(1)
¼” (6 mm)
Tube insert
(1)
¼” (6mm) PEX tube
(1)
Water fittings – The standard appliance does not include water fittings. Fisher & Paykel water fittings are available (part number: 841301). These parts need to be purchased separately by the
customer and comply with local regulations.
#10x40 pan head
Phillips screw (4)
Anti-tip bracket (1) Masonry plug (4)

6
PRODUCT DIMENSIONS inches (mm)
DOverall height of product* 71⁄” (1825)
EOverall width of product 35⅓” (890)
FMinimum cabinetry gap clearance from edge of custom panels** ⁄” (4)
GOverall depth of product (excluding front door panels) 23¾” (603)
HDepth of toe kick (measured from front of door panels***)2” (51)
IHeight of grille/toe kick* 4” (102)
JDepth of product front panels (excludes handles)*** ⅝” – ¾” (16–19)
* Includes mounted feet.
** Refer to custom door panel dimensions section.
***Door panels to be manufactured and fitted by cabinetmaker, min. ⅝” (16 mm) - max. ¾” (19 mm) thickness.
CAVITY DIMENSIONS inches (mm)
AOverall height of cavity 72” (1829)
BOverall width of cavity
(when adjoining cabinetry cannot share ⁄” (4mm) door gap)
36” (914)
COverall depth of cavity* 25” (635)
Total front panel width with required gaps at sides = 36” (914mm). (Refer to custom door panel dimensions section –
panel width + 2 x Fcabinetry gaps).
* Assumes a door panel thickness of ¾” (19mm).
E
B
H
C
A
A
I
J G
C
B
F
F
F
D
PROFILE VIEWFRONT VIEW
RS36A72J model shown only.
When designing custom door panels, with non-Water dispensing models.
4PRODUCT AND CAVITY DIMENSIONS
E
B
H
C
A
A
I
J G
C
B
F
F
F
D
E
B
H
C
A
A
I
J G
C
B
F
F
F
D
Flush with front
of cabinetry
PLAN VIEW
Framed: Finish return
Note: shows adjoining cabinetry
notsharing ⁄” (4 mm) door gap
⁄”
(4 mm)
E
B
H
C
A
A
I
J G
C
B
F
F
F
D
3½”
(89 mm)

7
DOOR CLEARANCE DIMENSIONS inches (mm)
ADepth of door (widest opening) measured from front of cabinetry 17⁄” (440)
BDepth of drawer (open) measured from front of cabinetry* 15¾” (400)
CMinimum door clearance** to adjacent wall* (115° – full internal access)* 11⁄” (300)
DMinimum door clearance** to adjacent wall* (90° – reduced internal access)* 3⁄” (100)
* Does not include the custom door panels or handles to be manufactured and fitted by cabinetmaker.
** Measured from front cabinetry edge.
90° DOOR OPENING115° DOOR OPENING
[FULL ROTATION]
A
B
C
BA
D
Wall Wall
90° DOOR OPENING115° DOOR OPENING
(FULL ROTATION)
4PRODUCT AND CAVITY DIMENSIONS

8
4PRODUCT AND CAVITY DIMENSIONS – WITH RD3672 DOOR PANEL SET
PRODUCT DIMENSIONS inches (mm)
DOverall height of product* 71⁄” (1825)
EOverall width of product 35⅓” (906)
FMinimum cabinetry gap clearance from edge of product ⁄” (4)
GOverall depth of product (excluding front door panels) 23¾” (603)
HDepth of toe kick (measured from front of door panels) 2” (51)
IHeight of grille/toe kick* 4” (102)
JHeight of bottom drawer panel 23⁄” (596)
KHeight of top door panels 44⁄” (1123)
LDepth of product front panels (excludes handles)** ¾” (19)
* Includes mounted feet.
** Optional EZKleen stainless steel front panels - Model no. RD3672 (non-Water dispensing model) and model no.
RD3672U (Ice & Water model).
E
B
H
C
A
DA
J
I
L G
C
B
F
F
F
K
FRONT VIEW
RS36A72J model shown with RD3672 door panel set.
CAVITY DIMENSIONS inches (mm)
AOverall height of cavity 72” (1829)
BOverall width of cavity
(when adjoining cabinetry cannot share ⁄” (4mm) door gap)
36” (914)
COverall depth of cavity 25” (635)
Total front panel width with required gaps at sides = 36” (914mm) (Eproduct width + 2 x Fcabinetry gaps).
Height of front panels with required gap above = Dproduct height + Fcabinetry gap.
E
B
H
C
A
DA
J
I
L G
C
B
F
F
F
K
PROFILE VIEW
E
B
H
C
A
DA
J
I
L G
C
B
F
F
F
K
Flush with front
of cabinetry
PLAN VIEW
Framed: Finish return
Note: shows adjoining cabinetry
notsharing ⁄” (4 mm) door gap
E
B
H
C
A
DA
J
I
L G
C
B
F
F
F
K
3½”
(89 mm)
⁄”
(4 mm)

9
4PRODUCT AND CAVITY DIMENSIONS – WITH RD3672/RD3672U DOOR PANEL SET
DOOR CLEARANCE DIMENSIONS inches (mm)
ADepth of door (widest opening) measured from front of door 17⁄” (440)
BDepth of drawer (open) measured from front of drawer, including handle 15¾” (400)
CDepth of drawer (open) measured from front of drawer, excluding handle 14⁄” (360)
DMinimum door clearance to adjacent wall* (115° – full internal access) 11⁄” (300)
EMinimum door clearance to adjacent wall* (90° – reduced internal access) 3⁄” (100)
* Measured from front cabinetry edge.
90° DOOR OPENING115° DOOR OPENING
[FULL ROTATION]
A
BC
D
BCA
E
Wall Wall
115° DOOR OPENING
(FULL ROTATION)
90° DOOR OPENING

10
!
A
C
B
A
C
B
!
5CAVITY PREPARATION
Electrical
Plumbing
Electrical
Plumbing
Recommended area above
cavity for connections
CAVITY DIMENSIONS inches (mm)
AOverall height of cavity 72” (1829)
BOverall width of cavity
(when adjoining cabinetry cannot share ⁄” (4mm) door gap)
36” (914)
COverall depth of cavity 25” (635)
Alternative electrical connection location
Floor
5⁄”
(150mm)
4⅓”
(110mm)
2⁄”
(75 mm)
5⁄”
(129mm)
5⁄”
(150mm)
31½” (800mm)
REAR VIEW OF CAVITY
RS36A72J RS36A72U
ELECTRICAL SPECIFICATIONS
Supply 115VAC, 60 Hz 115VAC, 60 Hz
Service 10 amp circuit 10 amp circuit
PLUMBING SPECIFICATIONS
Supply – ¼” (6mm) PEX hose or Copper tubing*
Pressure – Minimum 22 psi (150 kPa)
Maximum 120 psi (827 kPa) @ 20°C
Note: recommended that the electrical and water connection be located above the fridge cavity. Optional to locate
in an adjacent cabinet to either side of the fridge.
Do not locate water or electricity in this area, keep clear of connections.
CAUTION: central area can only fit electrical plug if it is placed within a recessed cavity.
*Water fittings kit – The standard appliance does not include water fittings. Standard Fisher & Paykel water fittings
kit are available (part number: 841301). These parts need to be purchased separately by the customer andcomply
with local regulations.
!
!
Frameless: Finish return,
sides and top
4⅓”
(110mm)
E
B
H
C
A
DA
J
I
L G
C
B
F
F
F
K
⁄”
(4 mm)
3½”
(89 mm)

11
6MAXIMUM DISTANCE OF POWER CORD
RS36A72J RS36A72U
ELECTRICAL SPECIFICATIONS
Supply 115VAC, 60 Hz 115VAC, 60 Hz
Service 10 amp circuit 10 amp circuit
PLUMBING SPECIFICATIONS
Supply – ¼” (6mm) PEX hose or Copper tubing*
Pressure – Minimum 22 psi (150 kPa)
Maximum 120 psi (827 kPa) @ 20°C
Power cord (excl.plug) – 80⁄” (2050mm)
RIGHT HAND SIDE
Power cord (excl.plug) – 80⁄” (2050mm)
LEFT HAND SIDE
Power cord (excl.plug) – 31½” (800mm)

12
7CUSTOM DOOR PANEL DIMENSIONS
ISO VIEW
H
FD
g
A
B
PROFILE VIEW
D
g
A
E
C
PROFILE VIEW
ISO VIEW
H
FD
g
A
B
PROFILE VIEW
D
g
A
E
C
ISO VIEW
RS36A72J
DIMENSIONS inches (mm)
AHeight of top door panel 44⁄” (1123)
BWidth of top door panel 17¾” (451)
CGap between top door panels ⁄” (4)
DHeight of bottom drawer panel 23⁄” (596)
EHeight from bottom of product to top of bottom drawer panel 27⁄” (698)
FWidth of bottom drawer panel 35⅓” (906)
GGap between top door panels and bottom drawer panel ⁄” (4)
HDepth of custom panels min. ⅝ - max. ¾” (16-19)
Maximum weight of an individual top door panel 22 pounds (10kg)
Maximum weight of bottom drawer panel 21 pounds (9.5kg)
Custom door panels and handles to be manufactured and fitted by cabinetmaker.
RS36A72J model shown only.
When designing custom door panels, with non-Water dispensing models.

13
7CUSTOM DOOR PANEL DIMENSIONS
The drawings below apply to non-Water dispensing models only. Dimensions are shown in Imperial (inches) and apply for the preparation and installation of custom door panels.
For Dwg and Dxf files of the below panel preparation download the folder on http://thekitchentools.fisherpaykel.com
All measurements to be made
from inner bottom corner.
For the second panel mirror
and repeat dimensions using
inner bottom corner as the
reference point.
Ensure handle is mounted
2⁄” from inner edge of panel
to the center – this will avoid
interference with brackets.
1⅜
16⁄
2⁄
15⁄
4⅓ 6⁄
24⁄ 26⁄
38⅝
40
Ø⁄ REF
12x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
TOP PANEL – REAR VIEW
Ø⁄ REF
10x Pilot holes recommended for
bracket attachment.
(Do not penetrate front surface).
15⁄
5⅓
1⁄3⁄
19⅜
21⅓
16⅜
All measurements to be made
from top and centerline.
BOTTOM PANEL – REAR VIEW
Ensure handle screw heads
are counter sunk into back of
panel to avoid interfering with
hanging bracket.

14
8ATTACH SIDE TRIM BRACKETS
1Break off the datum lip to each side trim bracket
anddiscard.
Repeat for all side trim brackets x6.
Discard
3Fix side trim brackets to the side of one enclosure
withscrews x2 (#8 x 16 pan head Phillips screw).
Ensure screws hold tight.
Repeat for remaining side trim brackets.
¾” (19mm)A
~4” (100mm)
~35” (900mm)
~4” (100mm)
2On one side of the finished enclosure, starting from the
top, measure ¾’’ (19 mm) from the front cabinetry edge
towards the back with the side trim bracket (refer to A).
Mark side trim bracket screw locations for the top,
center and bottom of the finished enclosure.
Repeat on the right side of the finished enclosure.
¾” (19mm)
IMPORTANT!
Before installing your appliance, ensure the dimensions
of the finished enclosure are correct for your appliance
following the ‘Product and cavity dimensions’ section.

15
9ATTACH ANTI-TIP BRACKET
IMPORTANT!
Safety requires refrigerators be stable when doors and/or drawer, are open. An anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand
a220.5pound (100kg) load. This will prevent the possibility of the appliance tipping forward, when doors and/or drawer, are open.
When fastening with masonry plugs and/or screws:
 Ensure the screws avoid electrical, gas and water conduits.
 Ensure the surface the bracket is fastened to withstand a 220.5 pound (100 kg) load.
 Ensure light-weight masonry material such as cinder block and new concrete (no curing time) are not used in installation.
 Do not use metallic materials that may corrode, stain and/or damage the enclosure.
If a minimum 2⅜” (60mm) overlap cannot be achieved
we recommend fastening a solid spacer (wooden beam etc)
behind the bracket.
1 Ensure the length of the spacer corresponds to the
enclosure’s width. Always secure the spacer to existing
studs on the enclosure wall (refer to C).
2Fix bracket to the wall with screws x4 (#10 x 40 pan head
Phillips screw). Ensure screws hold tight and the bracket
overlaps the appliance when it is positioned (2⅜” min.
(60mm)) for a secure hold.
WOODEN/PLASTER BOARD
WALL INSTALLATION SOLID WALL INSTALLATION
1Project the end of the above finished enclosure to the
center of the back wall and subtract 1¼” (31 mm). This
will locate the contact surface between the bracket and
the appliance (refer to A).
2 Fix bracket to the spacer with screws x4 (#10 x 40 pan
head Phillips screws). Ensure screws hold tight and the
bracket overlaps the appliance when it is positioned
(2⅜” min. (60mm)) for a secure hold.
1Project the end of the above finished enclosure to the
center of the back wall and subtract 1¼” (31 mm). This
will locate the contact surface between the bracket and
the appliance (refer to A).
Ensure a structural beam/wall stud closest to the center
of the wall enclosure is located.
SPACER INSTALLATION
2Mark screw locations to drill Ø ¼” x 1 ⅜” (Ø6.0 mm x 35 mm)
deep holes. Hammer masonry plugs into the wall until flush
x4. Fix bracket to the wall with screws x4 (#10 x 40 pan
headPhillips screws). Ensure screws hold tight.
A
2⅜” min.
(60mm)
overlap Bracket
PROFILE VIEW
1¼” (31mm)
C
2⅜” min.
(60mm)
overlap Bracket
PROFILE VIEW
1¼” (31mm)
Spacer
A
2⅜” min.
(60mm)
overlap Bracket
PROFILE VIEW
1¼” (31mm)

16
!0 CONNECT TO WATER AND ELECTRICAL SUPPLY
IMPORTANT!
 The water connection to your Ice & Water refrigerator must be installed by a qualified
plumber or a Fisher & Paykel Authorized Service Agent.
 The water connection instructions below are intended only for the professional installer.
 DO NOT use water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
 WARNING – connect to potable water supply only.
 DO NOT install on line pressure above 120 psi (827 kPa) or below 22 psi (150 kPa).
 DO NOT use on hot water supply (100°F [38°C max.]).
 AVOID contamination of pipes during installation.
 New water fittings (hose-sets) are to be used on the appliance. Old water fittings
(hose-sets)should not be reused.
 The standard appliance does not include water fittings. Fisher & Paykel water fittings
are available (part number: 841301). These parts need to be purchased separately by
thecustomer and comply with local regulations.
The assembly of Fisher & Paykel water fittings are outlined below, other water fittings
purchased separately also follow the installation steps below:
1 Ensure the refrigerator is NOT plugged into a power supply. Locate isolating faucet
forwater connection – cold water supply only. Tee and faucet fitting not supplied.
Ensure there is enough tubing for the water connection and to pull the appliance
outforservice, if required.
2 Uncoil the ¼” (6 mm) water tubing and thread one end through the opening in the rear
cover until it exits the front.
4Firmly insert water tubing into the PLV. The tube should push in at least ⅝” (16 mm)
before reaching the stop. Once inserted, pull gently on tubing to ensure it is locked
in(refer to B).
Secure the connection by attaching the locking key in between the PLV and water
tubing (refer to C). Mount the PLV back into the clip.
Rear view
3 At the front of the product, dislodge the PLV. Grasp the PLV from the clips by pulling
ittowards you (refer to A).
Front view
A
C
B

17
!0 CONNECT TO WATER AND ELECTRICAL SUPPLY
Final water tube connection
5 Position the appliance 1.5 – 2ft. (450 – 600 mm) in front of the finished enclosure
(refer to D). This will allow access behind the appliance for water and power
connections.
At the back of the appliance, cut the water tube to a suitable length for connecting
to the water outlet. Ensure there is enough tubing to pull the appliance out for
service, if required.
6 Assemble the following water fittings onto the other end of the water tube.
7 Fasten the faucet connection to the cold water supply. Take care
not to over-tighten the faucet connection. Turn isolating faucet
on and check that all connections are dry and free of drips.
8 Connecting power
At the back of your appliance adhere the power cord clip.
Connect the appliance to the electrical supply (115 VAC, 60 Hz
with thefitted plug and lead, and turn on. Ensure the appliance
isconnected to its own isolating switch.
Ensure excess power cord length is secured onto the clip (refer to E).
When pushing the appliance into position, take care not to roll over
ordamage the power cord and/or water tubing.
IMPORTANT!
 Ensure water tubing is routed away from any sharp objects, sharp corners (beware of kinking the tube as this will stop water flow), and not in a location where it can be kinked or squashed.
 Ensure a firm contact is observed as the appliance engages the anti-tip bracket, 2 ⅜” min. (60 mm) overlap.
1.5 – 2 ft.
(450 – 600 mm)
E
D
Insert tube Compression
sleeve
Compression
nut
Water tube

18
!1 PRODUCT PREPARATION
150
C
180
L
O
P
1 Carefully open the
refrigerator French doors
and remove the left hinge
end cap.
Hold onto the corner of
the end cap, firmly push
to the right to disengage
securing hook and pull
down (Refer to A).
2 Pull cap gently towards
the left hinge to remove
(Refer to B).
3 Remove the right hinge
end cap. Press on the
center of the cap and
push towards the right
hinge to remove.
Reserve end hinge cap
for later installation.
Reserve end hinge cap
for later installation.
150
C
180
L
O
P
4 Secure M8 studs into
the refrigerator doors,
ensure the open end
faces the top.
Repeat on all
refrigerator doors.
5 Secure mid-way,
M5 x 10 pan head
Phillips screw into
therefrigerator doors.
Repeat on all
refrigerator doors.
150
C
180
L
O
P
A
B