Fisher & Paykel WA1068G1 User manual

Installation instructions
Unpacking
To ensure the best performance from your new washer please follow the instructions below.
Removing the packaging
1. Remove the outer packaging.
2. Tilt the machine backwards and walk it off the
bottom packer one foot at a time (ensure lid is
still taped down).
3. Remove the bottom packer from under the
machine by tilting the machine backwards and
pulling the packer out the front.
4. Remove the tape, lift the lid and remove the
bowl packer from the bowl
5. Remove the hoses and accessories.
6. Keep the bottom packer and bowl packer in
case they are required for future transit.
Fig. 1 Tilt washer backwards to remove packer
Please ensure that the bottom packer has been removed BEFORE OPERATING your
machine.
Location
Your washer must be installed on a level surface and not on any textured floor coverings (eg carpet, rugs) to
ensure that the opening at the bottom of the machine is not obstructed.
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
1

In your clothes washer you will find:
• 1 hose guide.
• 2 inlet hoses.
• 4 rubber foot inserts.
Drain Hose
1. Carefully pull the drain hose out from the back of
the machine by pulling the exposed part of the
hose downward and outward.
2. To guide the drain hose over the tub or standpipe
the hose guide MUST be fitted to the drain hose.
To prevent siphoning the
drain hose should not
extend more than 20 mm
from the end of the guide.
The height of the standpipe
or tub should be between
850 – 2400 mm. The drain
hose can be trimmed to
length.
3. Place the drain hose in the tub or standpipe. Do
not fit the hose to a drain spigot. Drainage must not
be airtight in order to prevent siphoning.
Fig.2 Fitting the drain hose guide
Water Supply
• Your cold water should not exceed 35°C and your hot water should not exceed 65°C. Temperatures above
these may cause the machine to fault or cause damage to the machine.
• If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a Safe
Valve. This will ensure the hot water temperature remains within safe limits.
• Inlet water static pressure: Max.1 MPa (150 psi) Min. 34 KPa (5 psi)
• Inlet water flow rate at tap: Min. 6 litres / min
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
2

Hot ‘N’ Safe Valves available are:
RMC TVA 50HF
RMC TVA 75HFS
Adjustable between 35°C – 55°C
RMC TVA 50HP
For instantaneous gas hot water supply
Inlet Hoses
• New hose sets provided
with the washer shall be
used to connect the
washer to the water
mains.
• Old hose sets should not
be re-used.
1. Connect the straight ends of the inlet hoses to the
taps (there are washers fitted in both ends).
Connect the red connector hose to Hot, and the
white connector hose to Cold.
2. Connect the elbow ends of the inlet hoses to the
corresponding machine inlet valves. Inlet valves
are marked on the back of the machine. Ensure
the Hot valve is connected to the hot tap and the
Cold valve is connected to the cold tap.
H = Hot C = Cold
Fig.3 Inlet hose ends
Cold supply only:
If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the Hot inlet valve.
The cap prevents water leaking out of the hot valve. The cap is available from your Fisher & Paykel Dealer or
Authorised Repairer, Part No. 388491P. This appliance incorporates backflow protection complying with
AS3500.1. No further backflow protection is required for connection to the water supply.
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
3

Your washer does not have an internal heater to heat water.
Inlet hose replacement
We recommend replacing the inlet hoses every 5 years. Hoses should be checked from time to time and replaced
if any wear, cuts, bulges, kinks or leaks are found.
Draining
• Regularly check that your standpipe or tub is free from lint or other obstructions, which may affect how your
machine works or may cause flooding.
• In multi-storey apartments or any upper floor, the machine should be installed on a floor equipped with a drain.
• Draining must comply with local by-laws.
Levelling instructions
It is IMPORTANT to level the machine to ensure good spin performance and effective
detergent and fabric softener dispensing.
A spirit level is provided with your machine. Use this to level your machine, always placing it on a clean, flat
surface. The machine is level when the bubble sits in the centre, within the two lines.
Your washer is equipped with self-locking feet to ensure they do not move once you have levelled your machine.
To adjust the feet, pull down then twist to move them up or down.
After levelling, the corners of the washer should be clear of the floor and the machine must
not rock in any direction.
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
4

1. If not already installed, fit the rubber inserts into
all 4 feet on the base of the machine.
Fig.4 Levelling – Step 1
2. Move the machine to its final position using the
top corners to manoeuvre the product into
place (do not push on the centre front of the
machine). We recommend a minimum
clearance of 20 mm each side and 50 mm at
the rear of the machine.
3. With the lid closed, place the spirit level at the
centre back of the lid (near the control panel).
Pull the machine out and adjust the rear feet
(wind down) until the machine is level side to
side when in position.
Fig.5 Levelling – Step 3
4. Open the lid. Place spirit level on the flat
surface on the left side, inline with the centre of
the bowl. Adjust the front left foot (wind down)
until the machine is level.
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
5

5. Move the spirit level to the right side, in line with
the centre of the bowl. Adjust the front right foot
(wind down) until the machine is level, and
does not rock. There should be equal weight on
both front feet so that neither can be turned by
hand when the machine is in position.
Fig.7 Levelling – Step 5
6. Place the spirit level at the centre front of the
topdeck, forward of the lid lock slot. Check the
machine is level. Move the spirit level around to
all positions once more, checking the machine
is level in all areas. Check the machine does
not rock side to side, front to back, or corner to
corner.
Fig.8 Levelling – Step 6
Keep your spirit level for the next time you move or reposition your washer. If moving or
transporting your washer in the future, ensure you tape the lid down beforehand.
Completing your Installation
• Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hoses. Check
the hose connections for leaks again after 24 hours.
• Uncoil power cord, remove and discard the plastic pin cover, and plug into wall socket.
Installation test cycle
Your washer must be correctly installed before use. Check the installation and operation of the machine using the
following procedure:
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
6

1. Touch POWER to activate your washer.
2. Touch both the KEYLOCK and OPTIONS buttons at the same time, and hold for two seconds.
3. Touch START / PAUSE to start the installation test cycle.
4. The machine will beep to signal the end of the installation test cycle. Any faults will be displayed on the screen
(refer to the back of this user guide to help identify faults). If you need further assistance, please contact a
Fisher & Paykel Customer Care Representative. Refer to page 38 for contact details.
If there are no faults found, the washer will automatically turn off at the end of the
installation test cycle.
Clothes washer safety
• This clothes washer is not intended for use by children and persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Supervise children at all times to ensure they do not play with the washer.
Electrical Shock Hazard
• If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet
box), ensure that it is positioned so that it does not come into contact with water or moisture.
• Failure to do so may result in death or electrical shock.
Accessories and Spare Parts
Available from your Fisher & Paykel Dealer or a Fisher & Paykel Authorised Repairer.
Inlet Valve
Cap Part No. 388491P
Hose Inlet
Long (2m) Part No. 422680P
Hose Inlet
Large Bore Part No. 426123P
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
7

Available from your Fisher & Paykel Dealer or a Fisher & Paykel Authorised Repairer.
Drain Hose
Extension Part No. 425627P
Power
Cord
If the power cord of your clothes washer is damaged it must be replaced by a Fisher & Paykel
Authorised Repairer in order to avoid a hazard, as it is not a standard power cord.
https://producthelp.fisherpaykel.com/nz/Wash/Top_Loaders/WashSmart/WA1068G1/User_Guide_WA1068G1/02_Installation…
Updated: Sat, 30 May 2020 19:03:41 GMT
Powered by
8