Fisher & Paykel WH1160HG1 User manual

INSTALLATION GUIDE
NZ AU
FABRIC CARE SOLUTION
STACKED INSTALLATION
WH1160HG1, WH1160H1, DH9060HG1, DH9060H1, DH9060HLG1,
DH9060HL1, FC1260HG1, FC1260H1, FM2060SG1 and FM2060S1
models

2
COMPONENTS REQUIRED
TOOLS
PARTS
Supplied
F 6mm Allen key
F Spanner (washer)
F Spanner (plinth)
Not supplied
F Box cutter
F Phillips screwdriver
F Level
Supplied and required
F 4x M10 bolts
F 2x plinth bolt hole covers
F 4x short stacking kit screws
F 2x long stacking kit screws
Supplied and to be discarded
F 2x dryer front brackets
F 2x dryer rear brackets
F 2x dryer rear mounting screws

3
ACCESSING YOUR PRODUCT SPECIFICATIONS
For full product, cabinetry and service specifications, refer
to the Planning Guide. To access the Planning Guide, scan
the QR code or visit fisherpaykel.com/specify. Search by
appliance type, product name or model code.
1220
1260
1900
700
1920
700

4
PRIOR TO INSTALLATION
3. Ensure power will remain
accessible following install to
allow access for any future
product maintenance.
Service holes should be smooth
with gromets installed where
required.
Refer to the services section
of the Planning Guide for more
details.
2. Ensure floor is level and clear
and a finished return has been
created.
1. Ensure cabinetry and
servicing specifications have
been met and clearances have
been considered.
Refer to the Planning Guide for
details.
fisherpaykel.com/specify

5
UNPACK ALL PRODUCTS
Washer and Dryer:
Cut the straps and the line
printed on the top of the
carton. Lift to remove. Discard
braces and corner posts.
Remove any packaging and
accessories from the drum and
base packer.
Dispose of packaging
responsibly.
Fabric Care Cabinet:
Cut the straps and the line
printed on the back of the
carton. Cut to the nearest
corner and remove sleeve.
Discard braces, corner posts
and sleeve.
Remove packaging and
accessories from inside cabinet.
Dispose of packaging
responsibly.
Plinth:
Cut the straps and tape to
open the carton from the top.
Remove the EPS cap before
lifting the plinth out.
Set cardboard aside for later
use. Ensure accessories are
removed from the EPS cap
before discarding EPS and
rubber spacers responsibly.

6
Protect flooring before
positioning products as close
to the installation location
as possible, ensuring enough
working room is left available.
UNPACK ALL PRODUCTS

7
1. Push the front of the plinth
to open. Remove the divider
before closing the drawer.
LEVEL PLINTH
2. Place the plinth in its final
install location. Adjust the feet
using the supplied spanner until
the washer is level front to back
and corner to corner.
3. Using the spanner provided,
tighten the lock nuts against
the base of the plinth to lock
the feet in position.
Recheck that the plinth is level,
front to back and side to side.
Once level, move the plinth to
an accessible location to allow
washer/dryer to be installed.

8
1. Tilt the washer back onto a
protected surface such as the
plinth carton. Ensure cords
and hoses are not crushed. For
new products, we recommend
keeping the transit bolts fitted
during this step.
2. Unwind feet using the
supplied spanner to remove.
3. Partially fit the four M10 bolts
supplied with the storage plinth
to the washer.
FIT WASHER TO PLINTH

9
4. Using the spanner provided
as a spacer, ensure a 4mm gap
is left between the bolt head
and the chassis.
5. Align all four brackets to the
M10 bolts on the washer and
slot into place.
6. Ensure plinth is aligned on
both sides as shown before
tightening the front bolts with
the supplied spanner.
FIT WASHER TO PLINTH

10
7. Lift the washer upright,
avoiding lifting from the lid.
Take care as storage drawer
may open.
8. Tighten the rear bolts.
FIT WASHER TO PLINTH