Fisher & Paykel WM1490F User manual

Installation Instructions
Accessories
Please check you received the following accessories with your Fisher & Paykel washer.
You will find them inside the drum or attached to the packaging.
• 2 x Inlet hoses
• 1 x Drain hose guide
• 1 x Installation instructions and user guide
• 1 x Spanner
• 1 x Installation leaflet (attached to the top of the washer)
• 1 x Inlet valve cap
• 1 x Hose clamp
Unpacking
To ensure the best performance from your new washer please follow the instructions below
Removing The Packaging
1. Remove the outer packaging (including the polystyrene packer and plastic wrapping). All packaging must be
removed prior to use. Ensure these materials are kept out of reach of children. Note: a small amount of water
may be seen inside the packaging and inside the washer. This is the result of factory testing and is normal.
2. Tilt the machine backwards and ‘walk’ it off the base one foot at a time. Not doing so may cause damage to
your floor and washer.
3. Remove all packaging and accessories from inside the drum.
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
1

Removing The Transit Bolts
The clothes washer is fitted with 4 transit bolts at the rear to avoid damage during transportation.
The 4 transit bolts MUST be removed prior to operation of the machine. Failure to remove these will
result in damage to the machine.
To Remove The Bolts:
1. Use a spanner or socket to unscrew and remove all four transit bolts at the back of the washer (A).
2. Pull the black rubber grommets to remove the bolt, grommet and white plastic spacers from the machine. Keep
the transit bolts in case they are required for future transit of the machine. Never transport the machine
without the transit bolts properly fixed in place.
3. Cover the bolt holes with the white plastic plugs which are attached to the machine and located near each hole
(B). Push to clip into place.
Removing the transit safety bolts
Product Dimensions
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
2

FRONT VIEW
TOP VIEW
Product Dimensions WM1490F, WM1490P
mm
WM1480P, WM1280J
mm
A. Overall height of product 850 850
B. Overall width of product 600 600
C. Overall depth of product (excluding dial and door when closed) 645 570
D. Depth of door open 1065 1010
E. Minimum door clearance to adjacent wall 330 330
Standpipe height min. 800 – 1200 min. 800 – 1200
Maximum Capacity kg kg
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
3

Product Dimensions WM1490F, WM1490P
mm
WM1480P, WM1280J
mm
9.0 8.0
The exact height of your washer is dependent on how far the feet are extended from the base of the
machine. The space where you install your washer needs to be at least 40mm wider and 20mm
deeper than its dimensions.
• Electrical supply: 220 – 240V, 50Hz Sinusoidal, minimum 10A.
• Inlet water static pressure: Max. 1MPa (150psi), Min. 30kPa (4.5psi).
• Inlet water flow rate at tap: Min. 6 litres/min.
Location
Install the machine on a solid and level floor surface ensuring it has at least 20mm clearance on each
side. The washer must not be installed on any textured floor coverings (eg carpet, rugs).
This machine must not be installed and operated on a plinth.
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
4

Levelling The Machine
It is IMPORTANT to level the machine to ensure good spin performance,
and to minimise noise, vibrations and wear and tear on the washer.
1. Before positioning the machine in its final position, check that the
machine is level, front to back and side to side.
2. Manoeuvre the product into its final position (we suggest a minimum
clearance of 20mm each side).
3. Use a spirit level to check that the machine is correctly level. If
needed, pull the machine out. Loosen the lock nut using the spanner
provided and wind the feet up or down to correctly level the machine.
4. Using the spanner provided, tighten the lock nuts against the base of
the machine to lock the feet in position. Locking the feet
Connecting To The Water Supply
Inlet hose ends
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
5

Inlet Hoses
New hose sets provided with the
washer should be used to connect
the washer to the water mains.
Old hose sets should not be re-used.
We recommend the inlet hoses are
changed every 5 years.
Failure
to do so
may
result in
a flood
and
damage
to
property.
1. Connect the straight ends of the inlet hoses to the taps and the elbow ends to the corresponding machine inlet
valves. The hot valve is colour coded orange to make this easier. Tighten the inlet hose ends by hand until the
hose seal makes contact with the tap sealing face and then tighten a further half-turn. Make sure there are no
kinks in the hoses.
2. Turn the taps on and check for leaks. Check for leaks again after 24 hours.
The hot water temperature should not exceed 65°C and the cold water temperature not exceed 35°C.
Temperatures above these may cause the machine to fault or cause damage to the machine.
If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a Hot ‘N’ Safe
Valve. This will ensure the hot water temperature remains within safe limits.
Hot ‘N’ Safe Valves available are:
RMC TVA 50HF
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
6

RMC TVA 75HFS
Adjustable between 35°C – 55°C
RMC TVA 50HP
For instantaneous gas hot water supply
Water Supply Requirements:
• Inlet water pressure: Maximum 1MPa (150psi), Minimum 30kPa (4.5psi)
• Inlet water flow rate: Minimum 6 litres/minute
Cold Supply Only:
If you only have a cold water supply, the inlet valve cap (blanking cap) which came with your washer must be connected
to the hot inlet valve. The cap prevents water leaking out of the hot valve. This appliance incorporates backflow
protection complying with AS3500.1. No further backflow protection is required for connection to the water supply.
Your washer has an internal heater to heat water. If you do not connect a hot water inlet hose, your
washer will automatically recognise there is no hot water supply and its internal heater will heat the
cold water to the selected cycle temperature.
Draining
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
7

Drain Hose Placement in a Stand Pipe or Tub
1. To guide the drain hose over the tub or
standpipe the hose guide must be fitted to the
drain hose. The height of the standpipe or tub
should be between 800 – 1200mm.
2. Secure the hose guide so it cannot become
dislodged from the standpipe or tub.
• If the drain hose is placed
on the ground or if the
standpipe or tub is less
than 800mm high, the
washing machine will
continuously drain while
being filled (siphon).
• Regularly check that your
standpipe or tub is free
from lint or other
obstructions, which may
affect how your machine
works or may cause
flooding.
Fitting the drain hose guide
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
8

Attaching Drain Hose To Spigot
1. Guide drain hose through hose guide
2. Secure hose guide to back wall of cupboard
using a screw. The height of the drain hose
should be between 500 – 800mm from ground
level.
3. Attach drain hose to spigot and secure using a
hose clamp ensuring the blanking insert is
cleared from spigot.
4. Check for leaks.
• The drain hose should be checked from time to
time and replaced if any damage (eg wear, cuts,
bulges, kinks, leaks, etc) is found. Do not bend
the drain hose sharply, as this may cause it to
split.
• In multi-storey apartments or any upper floor, the
machine should be installed on a floor equipped
with a drain.
• Draining must comply with local by-laws.
Attaching drain hose to spigot
Electrical Connection
1. This appliance must be connected to a 220V – 240V, 50Hz, sinusoidal, minimum 10A electrical supply.
2. Uncoil the power cord, remove and discard the plastic pin cover and plug into a wall socket.
3. Connect the appliance to an earthed outlet protected by a fuse of suitable capacity.
• Check the power cord for damage and make sure it is not squashed or twisted when installing the washer.
• Always remove the power cord from a socket by the plug, not by the cord.
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
9

• If you are using an extension cord or a portable electrical outlet device (eg multisocket outlet
box), ensure that it is positioned so that it does not come into contact with water or moisture.
FAILURE TO DO SO MAY RESULT IN DEATH OR ELECTRICAL SHOCK.
• Do not touch or operate the machine with wet hands or with bare-feet.
• A damaged power cord must be replaced by a Fisher & Paykel trained and supported service
technician, in order to avoid a hazard. The appliance must not be operated until it is repaired, as
there is risk of electric shock.
• Do not operate this machine if it has been damaged during transport. Contact your Fisher &
Paykel dealer or Fisher & Paykel trained and supported service technician.
SPARE PARTS
Available from your Fisher & Paykel dealer or a Fisher & Paykel trained and supported service technician.
Hose Inlet Long (2m) Part No. 422680P
Hose Inlet Large Bore Part No. 426123P
Drain Hose Extension (Not suitable for attaching to a spigot). Part No. 425627P
Completing The Installation
Installation Test Cycle
Do this before you wash any items in your washer. This is to check that your washer is installed
correctly and that it is functioning correctly prior to use.
1. Turn your washer on by pressing the ‘POWER’ button.
2. Select the ‘Quick’ or ‘Super Quick’ cycle. Ensure the drum is empty and the door closed.
3. Touch
the button. The machine will start to fill.
• Observe the machine for any problems (eg leaking from the hoses, excess noise or vibrations).
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio…
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
10