Fisher-Price CLICK GHP42 User manual

1
TM
GHP42
OWNER’S MANUAL

2
TABLE OF CONTENTS
1BEFORE YOU BEGIN.................................................3
2PARTS .........................................................................4
3CHECK THE LOCATION FOR THE GATE................5
4SIZE THE GATE..........................................................8
5ASSEMBLE THE GATE...............................................9
6GATE CLAMP INSTALLATION.................................13
7GATE FASTENER INSTALLATION ..........................17
8GATE STAIRWAY INSTALLATION..........................24
9REMOTE FASTENER INSTALLATION....................29
10 REMOTE ADHESIVE INSTALLATION ....................32
11 INSTALL BATTERIES...............................................34
12 OPERATING THE GATE...........................................35
13 GATE CLOSURE ALERT SYSTEM...........................37
14 TEMPORARY GATE REMOVAL ..............................38

3
Remote requires two AA (LR6) alkaline batteries (included).
x2
1,5V
AA
(LR6)
1,5V
AA
(LR6)
Gate requires three AA (LR6) alkaline batteries (included).
x3
BEFORE YOU BEGIN
WARNING
Children have died or been seriously injured when gates are
not securely installed.
• ALWAYS install and use gate as directed using all required parts.
• STOP using when a child can climb over or dislodge the gate.
• NEVER use to keep child away from pool.
Keep this instruction sheet for future reference, as it contains
important information. Discontinue the use of the gate if it
becomes damaged, broken, or disassembled.
Adult assembly and setup is required to mount the gate and
remote, and install batteries.
Tools required for hardware installation:
Electric drill, 3/16"(4,76 mm) drill bit, hammer and Phillips
screwdriver (tools not included)
Tools required for clamp installation:
Phillips screwdriver (not included); and clamp tool (included)
Tools recommended, but not included:
Pencil, tape measure and level
To clean, wipe with a damp cloth.
Do not immerse.

4
PARTS
7,6 mm x 25,4 mm
Wall Anchor
x 8
2 inch
Extender 4 inch Extender 6 inch Extender
Mounting
Brackets
Remote Remote
Mount
Clamp
Tool
Clamps
Gate
Gate Bracket
Covers
Gate
Brackets
M3.5 x 15 mm Screw
x 10
M4 x 30 mm Screw
x 8

5
CHECK THE LOCATION FOR THE GATE
Measure the width
of the opening
where the gate will
be installed.
The width of the
opening should
be no less than
30" (76,2 cm) and
no greater than
42" (106,7 cm).
If using clamps,
also measure the
thickness of the
wall, doorway or
newel post.
If installing near a
stairway, you can
use clamps on the
newel post and
fasteners on the
wall.
Clamps should
not be used on
round newel
posts.
4⅜ –6⅜

The thickness of the
wall/doorway/newel
post should be no less
than 4⅜˝ (111,125 mm)
and no greater than
6⅜˝ (161,925 mm).

6
CHECK THE LOCATION FOR THE GATE
If using fasteners
to mount, check
to see if there is
a stud in the wall.
When fastening to a stud
or if fastening to wood,
you should not pre-drill
holes or use the wall
anchors.
Stud
Drywall
2 in
If attaching at the top
of stairs, measure the
distance from the first
step to the gate.
The distance from the
first step to the gate
should be at least two
inches (5,1 cm) or more.

7
It's assembly time!
Continue reading
or scan to watch
a step-by-step
assembly &
installation video.
fisher-price.com/assembly/GHP42

8
SIZE THE GATE
This gate fits in
openings from
30" (76,2 cm)
to 42" (106,7
cm). Use each
gate extender
alone or in
combination.
See below!
2˝
5,1 cm
4˝
10,2 cm
6˝
15,2 cm
2˝
2˝ 6˝
4˝
6˝4˝
6˝
2˝4˝ 6˝
Fits 30˝ - 31¼˝
(76,2 cm - 79,4 cm)
opening
Fits 31¼˝ - 33¼˝
(79,4 cm - 84,5 cm)
opening
Fits 37¼˝ - 39¼˝
(94,6 cm - 99,7 cm)
opening
Fits 33¼˝ - 35¼˝
(84,5 cm - 89,5 cm)
opening
Fits 35¼˝ - 37¼˝
(89,5 cm - 94,6 cm)
opening
Fits 39¼˝ - 41¼˝
(99,7 cm - 104,8 cm)
opening
Fits 41¼˝ - 42˝
(104,8 cm - 106,7 cm)
opening

9
ASSEMBLE THE GATE
If necessary, add
extenders to
fit the opening
where the gate
will be installed.
Refer to page 8
for sizing.
1
Fit the post on the
end of the mounting
bracket into the slot in
the side of the gate.
2

10
ASSEMBLE THE GATE
Rotate the
mounting bracket
down to fit to the
side of the gate.
3
4
x 1
M3.5 x 15 mm Screw