Fisher-Price 79534 User manual

Bounce ’n Play Activity Dome
Please save these instructions for future reference.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver.
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
Model Number: 79534
Instructions

Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us
toll-free, rather than return this product to the store. Usually we can solve the problem on the telephone or by sending
you replacement parts. Please call Fisher-Price®Consumer Affairs, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday
through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®Consumer Affairs, 636 Girard Avenue, East Aurora, New York 14052.
Consumer Information
2
• Never leave child unattended.
• To prevent suffocation from entrapment, use only the Fisher-Price®pad
provided. Never use additional padding or mattress.
• To prevent falls, use only for a child who is unable to push up on hands
and knees, pull up or sit unassisted.
• To prevent strangulation:
_Never place items with a string, such as hood strings or pacifier cords,
around a child's neck.
_Never place this product near a window where cords from blinds or
drapes can strangle a child.
• Never place product on an elevated surface.
• Never move or carry this product with a child in it.This product is not
designed to be used as a carrier and will become unstable.
• The Bounce ’n Play Activity Dome must be fully erected prior to each use.
• Never use plastic shipping bags or other plastic film as mattress covers.
They can cause suffocation.
WARNING

3
SHOWN ACTUAL SIZE
M5 x 113/16" Screw - 2 M5 Lock Nut - 2 M6 x 13/8" Screw - 8 M6 Lock Nut - 8
Base
Pad
Metal Canopy Stay
3 Toys
2 Base Wires
®
®
2 Covers
Plastic Mesh Cover Stay
Parts

4
Assembly
• Insert an M6 x 13/8" screw through each frame tube
and into the frame.
• Fit an M6 lock nut into each corresponding hexagonal
opening on the back of the frame.
Metal
Canopy
Stay
• Insert the metal canopy stay through the canopy tunnel.
• Position the base upright on a flat surface.
• Locate the end of the base with the mesh cover. Insert
the entire plastic mesh cover stay into one of the
button holes in the mesh cover.
• Be sure to tuck the plastic mesh cover stay away from
the button holes in both sides of the mesh cover.
Frame Tube Frame Tube
• Position the ends of the frame tubes against the
middle holes in a frame.
2
3
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price®for replacement parts and
instructions if needed. Never substitute parts.
M6 Lock Nut
Hexagonal
Opening
Base
Canopy Tunnel
Middle Hole Middle Hole
Frame
Frame
Frame Tube
Frame
Tube
M6 x 13/8" Screw - 4 M6 Lock Nut - 4
4
Base
Mesh Cover
Button Hole
1Plastic Mesh
Cover Stay

• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the
frame tubes to the frame on the other side of the base.
5
• Position the base wires around the base so that the
ends point upward and are in front of the lower holes
in a frame.
• Insert an M6 x 13/8" screw through each base wire and
into the frame.
• Fit an M6 lock nut into each corresponding hexagonal
opening on the back of the frame.
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the
base wires to the frame on the other side of the base.
6
Base Wire
Lower Hole
Base Wire
Frame
5
• Position one end of the metal canopy stay against the
upper hole in a frame.
• Insert an M5 x 113/16" screw through the hole in
the cover.
• Fit the end of the screw through the hole in the metal
canopy stay and into the hole in the frame.
• Push on the cover to insert and “snap” the tab on
the cover into the slot in the frame. Make sure you
hear a “snap”.
• Fit an M5 lock nut into the corresponding hexagonal
opening on the back of the frame.
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other end of the
metal canopy stay and the remaining cover to the
frame on the other side of the base.
Assembly
Upper
Hole
Cover
Slot Tab
Lower Hole
M6 Lock Nut - 4
M5 x 113/16" Screw - 2 M5 Lock Nut - 2
Metal Canopy Stay
7
M6 x 13/8" Screw - 4

®
• Lift the canopy.
• Fasten the pad fasteners to the base fasteners.
• Attach the toys to the canopy fasteners.
Assembly is now complete, but Bounce ‘n Play
Activity Dome is not ready for use. Please refer to
the Use instructions, page 7, steps 3 and 4.
Pad
Fastener
Base Fastener
Toys Canopy
Fasteners
Sides of Base Wire
• Grasp both sides of a base wire.
• Pull both sides of the base wire outward and then let
the base wire rotate down.
Note: If the base wire does not freely rotate down, pull
the sides of the base wire further outward.
6
Assembly
®
Carry Straps
• Position the product on a flat surface.
• Unfasten the carry straps.
1
2
Use
8
To Unfold

Using the Canopy
7
Base Wire
Frame
Groove Groove
3
• Lift the product up slightly so that the base wire
“snaps” into the groove in each frame. Make sure
you hear a “snap”.
• Repeat Use Steps 2 and 3 to unfold the other base wire.
• Push down on the product to
be sure the base wires are in
the correct position.The base
wires should rest in the groove
in each frame.
Use
Base Wire
Groove
Frame
Correct
®
• Adjust the canopy and mesh cover up.
• While holding the mesh cover up, fasten the
zipper closed.
Canopy Up
Mesh
Cover Up
Zipper
®
• Adjust the canopy up or down.
Canopy Down
Canopy Up
Using the Mesh Cover
6
5
4

If you have any questions about this product:
In CANADA: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Questions? 1-800-567-7724.
In GREAT BRITAIN: Mattel U.K., Ltd., Helpline: 01628 500302.
In AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812 (valid only in Australia).
The pad is machine washable.Wash the pad separately
in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
The fabric, frame and toys may be wiped clean using a
mild cleaning solution and a damp cloth.
Care
• Grasp both sides of a base wire.
• While lifting the product up slightly, pull both sides of
the base wire outward to remove the base wire from
the groove in each frame.
Frame
Groove
Base Wire
Groove
7
Base Wire
• Rotate the base wire up.
• Repeat this procedure to fold the other base wire.
8
Correct
®
• Fasten the carry straps.
Carry Straps
9
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. 79534 B 79534-0920
©1998 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. Printed in Hong Kong
To Fold for Portability
Use Use