Fisher-Price W2163 User manual

W2163
www.fisher-price.co.uk
IMPORTANT! KEEP FOR FUTURE REFERENCE

2
WARNING
To prevent serious injury or death:
Use only for a child who is able to hold•
head up unassisted and who is not
able to walk or climb out of the product
and who weighs less than 12 kg.
Never leave child unattended. Always•
keep child in view while in product.
Never use near steps or pools,•
hot surfaces or areas that may be
hazardous to a child. Product may
move during use.
To avoid tip over, place product on•
a at, level surface.
Do not use product as a swing.•
Be sure child is correctly and safely•
positioned in the seat.
Strings can cause strangulation! DO•
NOT place items with a string around
child’s neck, such as hood strings
or pacier cords. DO NOT suspend
strings over product or attach strings
to toys.
Consumer Information
IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
Please read these instructions before assembly and use of•
this product.
Adult assembly is required. Tool needed for battery installation:•
Phillips screwdriver (not included).
Requires three “AA” (LR6)• alkaline batteries (not included) for
electronic toy operation.
Use only for a child:•
- who is able to hold head up unassisted
- who is not able to climb out
- who weighs less than 12 kg (26 lbs) and is less than 32 inches
(81 cm) in height.
Recommended time limit for each use is 20 minutes.•
Product features and decorations may vary from photos.•
Frame
3 Bases
Electronic Toy Spinning Ball Elephant Toy
Pad
Seat
Hint: You may want to install batteries in the electronic toy before
beginning assembly. Please refer to the Battery Installation section.
Parts
2 Hanging Toys Spinning Disc
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2011 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO W2163pr-0726

3
4
Pull the pad through the seat. Wrap the edges of the pad around•
the outside of the seat.
Place the bases on a flat surface.•
While pressing the button on the short tube of a base, insert it•
into the long tube on another base. Continue to slide the short
tube into the long tube until you hear a “click”.
Repeat this procedure to assemble the remaining base to the•
base assembly.
2
PRESS
Base Short Tube
Base Long Tube
Insert and• “snap” the elephant toy, spinning disc, electronic toy,
and spinning ball into the slots on the seat ring.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
1
Electronic ToySpinning Disc
Elephant Toy
Spinning Ball
Assembly
Star Marking
Star Marking
Seat
Peg Peg
Pad
Slots
Slots
3
Position the seat so that the inside (ribbed side) is up and the star•
marking is toward you.
Fit the yellow slots on the pad to the seat pegs on either side of•
the star marking .

4
8
Seat with Pad
Seat Ring
Insert and• “snap” the seat with pad into the seat ring. Pull up on
the seat to be sure it is secure.
Assembly
5
Fit the other six button holes in the seat pad onto the corresponding•
pegs on the seat.
PRESS
6
Frame Tube
Base Tube
While pressing the button on a frame tube, insert it into a base•
tube. Continue to slide the frame tube into the base tube until you
hear a “click”. Pull up on the frame tube to be sure it is secure.
Repeat this procedure to assemble the two remaining frame tubes•
to the base tubes.
7
Fit the hanging toys into the slots on the frame tubes.•
Push to "• snap" the toys in place.
2 Hanging Toys

5
Loosen the screws in the battery compartment door with a Phillips•
screwdriver and remove the battery compartment door.
Insert three “AA” (LR6)• alkaline batteries into the
battery compartment.
Replace the battery compartment door and tighten the screws.•
If this product begins to operate erratically, you may need to reset•
the electronics. Slide the power/volume switch off and then back on.
When sounds or lights become faint or do not work at all, it’s time•
for an adult to replace batteries.
Hint: We recommend using alkaline batteries for longer battery life.
1,5V x 3
“AA” (LR6)
Battery Installation
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
Do not mix old and new batteries or batteries of different types:•
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
Insert batteries as indicated inside the battery compartment.•
Remove batteries during long periods of non-use. Always remove•
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
Never short-circuit the battery terminals.•
Use only batteries of the same or equivalent type, as recommended.•
Do not charge non-rechargeable batteries.•
Remove rechargeable batteries from the product before charging.•
If removable, rechargeable batteries are used, they are only to be•
charged under adult supervision.
Battery Safety Information
Setup and Use
WARNING
To prevent serious injury or death:
Use only for a child who is able to hold•
head up unassisted and who is not
able to walk or climb out of the product
and who weighs less than 12 kg.
Never leave child unattended. Always•
keep child in view while in product.
Never use near steps or pools,•
hot surfaces or areas that may be
hazardous to a child. Product may
move during use.
To avoid tip over, place product on•
a at, level surface.
Do not use product as a swing.•
Be sure child is correctly and safely•
positioned in the seat.
Strings can cause strangulation! DO•
NOT place items with a string around
child’s neck, such as hood strings
or pacier cords. DO NOT suspend
strings over product or attach strings
to toys.
Protect the environment by not disposing of this product•
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).

6
Place your child in the seat. Check the distance between your•
baby’s feet and the floor. Your child’s toes should touch the floor
(without bouncing). If your child’s entire foot is touching the floor
or the toes are not touching the floor at all, adjust the height to
any of three positions (one for the smallest child and three for the
tallest child).
1
Seat Height Adjustment
Remove your child from the seat.•
Lift the seat ring so the bottom faces you.•
Locate the strap bar and pull it open.•
Strap Bar
BOTTOM VIEW
BOTTOM VIEW
2
Strap
3
Pull the strap to the desired height• .

7
Seat Height Adjustment
5
Push to• “snap” and fasten the strap bar.
Repeat this process to attach the other two straps to the seat ring.•
IMPORTANT! Make sure all three straps are adjusted to the
same height.
Slide the power/volume switch to:•
On with low volume
On with high volume
Off
Slide the mode select switch to short play or long play.•
Short Play – Baby's jumping activates lights and music.
Long Play – Mom can choose this mode to play up to
5 minutes of continuous music.
Mode Select Switch Power/Volume Switch
Jumpin’ Fun!
Slot
Slot
4
Fit the strap bar into the desired slot in the strap.•

8
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked
Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory
Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Care
The seat pad is machine washable. Wash it separately in cold•
water on the gentle cycle. Do not use bleach. Tumble dry
separately on low heat and remove promptly.
The frame, seat, seat ring, straps and toys may be wiped clean•
using a mild cleaning solution and damp cloth. Do not use bleach.
Do not use harsh or abrasive cleaners. Rinse clean with water to
remove soap residue. Do not immerse the electronic toy.
Remove the Seat and Pad
Lift the seat ring. While pressing near any notch on the seat,•
pull the seat from the seat ring. Turn the seat over. Remove the
pad slots from the pegs on the seat. Remove the pad.
Replace the Seat and Pad
Please follow the Assembly instructions.•