Fisherbrand 50152744 User manual

18L low temp incubator Fisherbrand
© 2016 Thermo Fisher Scientific. All rights reserved.
This Instruction Manual is copyright protected. Rights resulting thereof, particularly reprint, photomechan-
ical or
digital post-processing or reproduction, even in part, are only allowed with the written consent of Thermo
Fisher
Scientific.
This regulation does not apply to reproductions for in-plant use.
The contents of this document are subject to change without notice. Concerning translations into foreign
languages, the English version of these operating instructions is binding.
Trademarks
All trademarks mentioned in the operating instructions are the exclusive property of the respective manufac-
turers.
Thermo Fisher Scientific
300 Industry Drive
Pittsburgh, Pennsylvania 15275
United States
Thermo Fisher Scientific provides this document to its customers with a product purchase to use in the
product operation. This document is copyright protected and any reproduction of the whole or any part of
this document is strictly prohibited, except with the written authorization of Thermo Fisher Scientific.
The content of this document are subject to change without notice.
All technical information in this document is for reference purposes only. System configurations and
specifications in this document supersede all previous information received by the purchaser.
This document is not part of any sales contract between Thermo Fisher Scientific and a purchaser. This
document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and
Conditions of Sale shall govern all conflicting information between the two documents.

Fisherbrand 18L low temp incubator 1-1
1
Chapter 1 Safety Information1-1
Basic operating precautions1-1
Safe usage instructions1-2
Guarantee1-2
Explanation of safety information and symbols1-2
Intended use of the device1-4
Chapter 2 Delivery of the device2-1
Packaging2-1
Acceptance inspection2-1
Scope of supply2-1
Chapter 3 Installation3-1
Environmental conditions3-1
Room ventilation3-2
Installation3-2
Transport3-2
Chapter 4 Description of unit4-1
Device overview4-1
Mains connection4-2
Useable space components4-2
Condensation tray4-3
Chapter 5 Installation procedures5-1
Insert the perforated plates 5-1
Preparing the useable space5-1
Mains connection5-1
Chapter 6 Operation6-1
Preparing the device6-1
Starting Operation6-1
Chapter 7 Handling and control7-1
Powering up and down7-1
Setting the temperature7-2
Interior light7-2
Chapter 8 Shut-down8-1
Shutting the device down8-1
Table of contents

Table of contents
1-2 18L low temp incubator Fisherbrand
Chapter 9 Cleaning and disinfection9-1
Empty the condensation tray 9-1
Cleaning exterior surfaces9-1
Wipe / spray disinfection9-1
Chapter 10Maintenance10-1
Inspections and checks10-1
Chapter 11Disposal11-1
Overview of materials used11-2
Chapter 12Technical Data12-1
Chapter 13Accessories13-1

Fisherbrand 18L low temp incubator 1-1
1
Safety Information
Basic operating precautions
These operating instructions describe the Fisherbrand 18L low temp incubator.
The Fisherbrand 18L low temp incubator has been manufactured to the latest state of the art
and been tested thoroughly for flawless functioning prior to shipping. However, the device
may present potential hazards, particularly if it is operated by inadequately trained personnel
or if it is not used in accordance with the intended purpose. Therefore, the Fisherbrand 18L
low temp incubator following must be observed for the sake of accident prevention:
• The Fisherbrand 18L low temp incubator is only to be used by trained and authorized
personnel.
• The present operating instructions, applicable safety data sheets, plant hygiene guidelines
and the corresponding technical rules issued by the operator shall be used to create written
procedures targeted at personnel working with the subject matter device, detailing:
• the disinfection measures to be employed for the device and the accessories used with
it,
• not to be used in a damp atmosphere,
• the protective measures which are to be taken when processing certain agents,
• action to be taken in case of accidents.
• Maintenance work on the device is only to be carried out by trained and authorized
specialists. The device is not to be repaired. It will be repaired during the warranty period
and then has to be disposed of by the customer; he having to purchase a new one should it
still be required.
• The contents of these operating instructions are subject to change at any time without
further notice.
• Concerning translations into foreign languages, the English version of these operating
instructions is binding.
• Keep these operating instructions close to the device so that safety instructions and
important information are always accessible.
• Should you encounter problems that are not detailed adequately in these operating
instructions, please contact Fisher Scientific immediately for your own safety.

Safety Information
Safe usage instructions
1-2 18L low temp incubator Fisherbrand
Safe usage instructions
Observe the load of the stiffening plates (refer to chapter technical data).
Do not charge the floor of the interior as there is a risk of the inserted item overheating.
Distribute the items evenly and do not place them too close to the interior walls, so as to
ensure a good temperature distribution.
Guarantee
Fisher Scientific warrants the operational safety and functions of the Fisherbrands 18L low
temp incubator only under the condition that:
• the device is operated and serviced exclusively in accordance with its intended purpose
and as described in these operating instructions,
• the device is not modified,
• only original spare parts and accessories that have been approved by Fisher Scientific are
used.
The warranty is valid from the date of delivery of the device to the operator.
Explanation of safety information and symbols
Safety information and symbols used in the operating instructions
Indicates a hazardous situation which, if not avoided, will result in
death or serious injuries.
Indicates a hazardous situation which, if not avoided, could result
in death or serious injuries.

Indicates a situation which, if not avoided, could result in damage
to property.

Safety Information
Explanation of safety information and symbols
Fisherbrand 18L low temp incubator 1-3
Additional symbols for safety information
Symbols on the device / Applicable standards
Is used for useful hints and information regarding the application.
Wear safety gloves!
Wear safety goggles!
Harmful liquids!
Electrical shock!

Fire hazard!

Contamination hazard!

Observe operating instructions

Mark of conformity USA/Canada
This device has been tested by the Canadian Standards Association
(CSA) on the basis of CAN/CSA-C22.2 No. 61010-1 and CAN/CSA-C22.2
No. 61010-2-010, UL 61010-1 and IEC 61010-2-010 and bears the cCSAus
symbol for tested safety. It is subject to production monitoring by the
CSA.

Safety Information
Intended use of the device
1-4 18L low temp incubator Fisherbrand
Intended use of the device
Correct use
The Fisherbrand 18L low temp incubator is a laboratory device in the standard version and
serves the preparation and cultivation of microbiological cultures and micro-organisms in
safety levels L1 and L2. The device enables the special physiological ambient conditions
which these cultures require to be simulated due to it exactly controlling the useable space
temperature. The device is only to be used in closed spaces.
Incorrect use
To avoid the risk of explosion do not load the device with tissue, material, or liquids that:
• are easily flammable or explosive,
• release vapor or dust that forms combustible or explosive mixtures when exposed to air,
• release poisons,
• create a humid atmosphere,
• release dust,
• have an increased biological risk potential (safety level L3, L4).
The devices are not to be stacked.

A use of the device which is not intended can be hazardous.

Fisherbrand 18L low temp incubator 2-1
2
Delivery of the device
Packaging
The Fisherbrand 18L low temp incubator are delivered in a rugged packaging box. All
packaging materials can be separated and are reusable:
Packaging materials
Packaging carton: Recycled paper
Foam elements: Styrofoam (CFC-free)
Packaging film: Polyethylene
Acceptance inspection
After the device has been delivered, check the delivery immediately for:
• completeness,
• possible damage.
If components are missing or damage is found on the device or the packaging, in
particular damage caused by humidity and/or water, please notify the carrier as well as
Fisher Scientific Technical Support immediately.
Scope of supply
Quantity of components supplied Pieces
Perforated plate 2
Power cord, version US/JP 1
Mains adapter 12 V DC 1
Instruction Manual 1

Delivery of the device
Scope of supply
2-2 18L low temp incubator Fisherbrand

Fisherbrand 18L low temp incubator 3-1
3
Installation
Environmental conditions
The Fisherbrand 18L low temp incubator device must only be operated in a location that
meets all of the specific ambient condition requirements listed below:
Location requirements
• Dry place of erection within a closed space which is free from droughts.
• Dust loading should be in keeping with the degree of contamination, which is Degree 2
according to IEC EN 61010-1. Using the incubator in an atmosphere with electrically
conductive dust is prohibited.
• The minimal distance to adjacent surfaces must be observed on all sides (see Section 3.3).
• The operating room must be equipped with appropriate ventilation.
• Solid, level, fire-proof surface.
• Vibration-proof substructure (floor stand, lab table) capable of bearing the dead weight of
the device and its accessories (particularly if two devices are stacked).
• The electrical circuitry of the device has been designed for an operating height of up to
2000 m above sea level.
• The permissible ambient temperature is between +18 °C and 32 °C (+64.4 °F and +
89.6 °F) for an incubation temperature of between 17 °C and 40 °C (62.6 °F and 104 °F).
• Relative humidity up to 80% (maximum; preferably 60-70%), non condensing.
• Dew is to be avoided, e.g. after changes of location or transportation. Should
condensation exist, wait until the moisture has evaporated completely before connecting
the device to a power source and powering up.
• Avoid direct exposure to sunlight.
• Devices that produce excessive amounts of heat must not be placed near the device.
• Storage temperature: When the device is placed in intermediate storage, make sure that
the ambient temperature is between 20 °C and 60 °C (68 °F and 140 °F) and the
maximum relative humidity does not exceed 90%, non-condensing.

Installation
Room ventilation
3-2 18L low temp incubator Fisherbrand
Room ventilation
Heat dissipating from the device during continuous operation may cause a change in the
room climate.
Therefore, the device must only be installed in rooms with sufficient ventilation.
Do not install the incubator in room recesses without ventilation.
When several devices are to be placed in the same room, additional ventilation may have to
be provided as necessary.
The room ventilation is to be of a technical form which is designed in accordance with the
thermal input.
Installation
When installing the device, make sure that the installation and supply connections remain
freely accessible. The minimum wall clearance is 5 cm / 2 in on the sides and back. No other
devices are to be placed on the device.
The cooling fan on the back of the device is not to be covered. 
It is not to suck-in any loose items (e.g. paper).
Transport
The device is not to be lifted by the door or attachments when being transported.

Fisherbrand 18L low temp incubator 4-1
4
Description of unit
Device overview
Front view
12
4
3
Abbildung 4-1 Front view Fisherbrand 18L low temp incubator
[1] Temperature display
[2] Control panel
[3] Door/door handle
[4] Perforated plate

Description of unit
Mains connection
4-2 18L low temp incubator Fisherbrand
Rear view
.
Abbildung 4-2 Rear view Fisherbrand 18L low temp incubator
[1] Fan
[2] Mains adapter
Mains connection
The mains connection of the device is done by connecting the enclosed mains adapter to the
100 V or 240V a.c. supply; mains fluctuation +/-10%, 50/60 Hz
Useable space components
The surface of the useable space of the Fisherbrand 18L low temp incubator is reduced to a
minimum and therefore supports the protection against contamination and its easy and
efficient elimination. All of the parts of the inner container of the Fisherbrand 18L low temp
incubator are made of plastic (the racks are made of stainless steel) and have a smooth and
easy to clean surface.
A heat exchanger element [Abb. 4-3; 1] in the rear wall serves to heat or cool the useable
space as required.
The useable space lighting can be switched on using the button on the control panel.
Perforated plate
The metal plates have an anti-tipping device. The perforated plate is described in detail in
the chapter entitled Commissioning.

Description of unit
Condensation tray
Fisherbrand 18L low temp incubator 4-3
Condensation tray
A removable tray [Abb. 4-3; 2] is provided underneath the device which collects the
condensation which collects whilst the useable space is in use.
.
Abbildung 4-3 Cooling or heating elements and the condensation tray in the Fisherbrands
18L low temp incubator

Description of unit
Condensation tray
4-4 18L low temp incubator Fisherbrand

Fisherbrand 18L low temp incubator 5-1
5
Installation procedures
Remove the packing foil.
Insert the perforated plates
Remove the transport securing devices from the perforated plates.
Insert the perforated plates in the grooved profiles on the side walls of the useable space.
Preparing the useable space
The Fisherbrand 18L low temp incubator is not delivered in a sterile condition.
The following useable space components should be checked for cleanliness and disinfected
prior to use:
• perforated plates,
• useable space surfaces,
•doorseal,
• useable space door.

Installation procedures
Mains connection
5-2 18L low temp incubator Fisherbrand
Mains connection
Electrical shock
Contact with live electrical components may cause a lethal electric
shock.
Before connecting the device to the power supply, check the power
cord and the plug for damage. Do not use damaged cables for con-
necting the device to the power supply!
Connect the device to the on site fused mains supply with the following values:
• Safety fuse (time-lag) T 16 A or circuit breaker B 16.
• Connection via a fault current circuit breaker (triggering current < 30 mA) is
recommended.
Connection to the power supply source
1. Before connecting the device to the power source, check to see if the power supply
voltage corresponds with the specifications on the nameplate on the rear of the device. If
the voltage (V) and current (A) ratings given are not as required, do not connect the
device to the power source!
2. Connect the IEC connector to the socket on the rear of the device.
3. Insert the earthed plug [3] of the mains cable in a correctly earthed and fused socket.
Power sockets
The socket which the device is connected to is to be fully accessible
when operating the device so as to ensure that the plug can be re-
moved should danger occur!
4. Make sure the power cord is not subjected to tensile or compressive force.
Condensation
The device should be in the room for a sufficiently long duration be-
fore it is switched on, in order to ensure that it can reach the ambi-
ent temperature. This prevents condensation forming on live
components.

Fisherbrand 18L low temp incubator 6-1
6
Operation
Preparing the device
The device must not be released for operation before all major start-up activities have been
completed (see chapter Installation procedures).
Device Check
Prior to starting operation, the following device components must be checked for their correct
function:
• The door seal in the front frame must not be damaged.
• The perforated plates have to have been correctly inserted.
Starting Operation
1. Switch the device on with button .
2. The display shows the current useable space temperature.
3. Set the target values for the temperature using buttons and on the control
panel.
4. Wait until the device has reached the set temperature. The temperature control regulates
the temperature at the set target temperature value.
5. Load the useable space.
Proper loading
To ensure sufficient air circulation and uniform heating of the sam-
ples, do not use more than 70% of the maximum surface area of the
useable space. Bulky objects in the useable space that dissipate
heat may impair heat distribution.

Operation
Starting Operation
6-2 18L low temp incubator Fisherbrand