FiT 501105 User manual

501105 | 501228 | 501229 | 501230
501244 | 501267 | 501268
INSTRUCTION MANUAL
Biketec GmbH
Luzernstrasse 84
CH-4950Huttwil
T [phone]
[e-mail]
fit-ebike.com
TIRE PRESSURE SENSOR FIT
NETWORKED
CUSTOMISED
INTELLIGENT

INSTRUCTION MANUAL TPMS FIT
TABLE OF CONTENTS
1 PREFACE 3
2 ABOUT THESE OPERATING INSTRUCTIONS 4
2.1 MANUFACTURER................................................. 4
2.2 LANGUAGE..................................................... 4
2.3 DECLARATIONOFCONFORMITY ........................................ 4
2.4 ONINFORMATION ................................................ 4
2.5 WARNINGS IN THESE OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 SAFETY INSTRUCTIONS 5
3.1 GENERALINFORMATION............................................. 5
3.2 TYREPRESSURESENSOR............................................ 5
4 PRODUCT AND TECHNICAL SPECIFICATIONS 6
4.1 FITTYREPRESSURESENSOR.......................................... 6
4.2 PROPERUSE ................................................... 6
4.3 IMPROPERUSE.................................................. 6
4.4 UPDATES...................................................... 6
4.5 TECHNICALDATA................................................. 7
4.5.1 FIT AV-SCHRADER TYRE PRESSURE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.5.2 FIT SV-PRESTA SCLAVERAND TYRE PRESSURE SENSOR . . . . . . . . . . . . . . . . . . . . . . 7
5 FITTING 8
5.1 FIT AV-SCHRADER & FIT SV-PRESTA SCLAVERAND TYRE PRESSURE SENSOR . . . . . . . . . . . . . . 8
5.2 FILLINGWITHTUBELESSSEALANT....................................... 12
6 OPERATION 13
6.1 INITIALOPERATION................................................ 13
6.2 DISPLAYANDSETTINGS............................................. 20
6.2.1 FITDISPLAYCOMFORT ......................................... 20
6.2.2 FITDISPLAYCOMPACT ......................................... 22
6.2.3 FITREMOTEDISPLAY .......................................... 24
7 CLEANING AND SERVICING 26
7.1 BASICCLEANING ................................................. 26
7.1.1 CLEANING THE TYRE PRESSURE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8 TROUBLESHOOTING, FAULT CLEARANCE AND REPAIR 27
8.1 TROUBLESHOOTING AND FAULT CLEARANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.1.1 TYRE PRESSURE IS NOT DISPLAYED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.1.2 ERRORTABLE .............................................. 27
8.2 REPAIR....................................................... 27
8.2.1 ORIGINALPARTS............................................. 27
9 RECYCLING AND DISPOSAL 28
9.1 DISPOSAL ..................................................... 28
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 2

INSTRUCTION MANUAL TPMS FIT
1 PREFACE
Dear FIT customer,
The FIT system offers many useful functions and options and we are pleased that you have decided to choose our
system.
Please read through the operating instructions carefully to ensure you use the system safely and get off to a quick
start.
We hope you enjoy discovering the FIT’s functions and have a fun ride every time you use it.
Thank you for placing your trust in FIT.
Your FIT Team
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 3

INSTRUCTION MANUAL TPMS FIT
2 ABOUT THESE OPERATING INSTRUCTIONS
2.1 MANUFACTURER
Biketec GmbH
Luzernstrasse 84
CH-4950 Huttwil
fit-ebike.com/en-en/
2.2 LANGUAGE
The original operating instructions are written in German. A translation is invalid without the original operating in-
structions.
2.3 DECLARATION OF CONFORMITY
Biketec GmbH hereby declares that the products described in these operating instructions comply with EU directives.
The complete EU Declaration of Conformity is available online at: fit-ebike.com/en-en/service/declaration/
2.4 ON INFORMATION
Different markings are used in the operating instructions to make them easier to read.
2.5 WARNINGS IN THESE OPERATING INSTRUCTIONS
Warnings indicate hazardous situations and actions. You will find the following warnings in the operating instructions:
DANGER
May lead to serious or even fatal injuries if ignored. Medium-risk hazard.
CAUTION
May lead to minor or moderate injuries if ignored. Low-risk hazard.
NOTICE
May lead to material damage if ignored.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 4

INSTRUCTION MANUAL TPMS FIT
3 SAFETY INSTRUCTIONS
3.1 GENERAL INFORMATION
Please read all safety instructions carefully. Failure to comply with the warnings or take residual risks into account
may result in electric shock, fire and / or serious injury.
Keep the operating instructions in a safe place and have them readily available to consult. Pass these instructions
on if you provide your e-bike for someone else’s use.
The generic names used in these operating instructions, such as motor, battery and operating element, all refer to
original FIT e-bike components.
3.2 TYRE PRESSURE SENSOR
Do not use the sensor if it is damaged and / or if there are other visible defects. You must use a new sensor in such
cases. For safety reasons and to guarantee optimum operation, we recommend having maintenance and repair work
carried out by your specialist dealer only.
The e-bike manufacturer is not liable for and does not replace any parts which have been damaged as the result of in-
correct fitting or incorrect usage or which have been damaged in an accident which is neither partially nor completely
due to a fault in the sensor.
Biketec GmbH has not tested the compatibility of third-party manufacturer parts with the sensor and can thus not
approve their use. To ensure optimal operation, the sensor must only be used with original Biketec valves and original
Biketec accessories and only fitted with installation tools provided by Biketec GmbH. If the installation and safety
instructions are not observed, this can cause a fault which is not covered by the warranty.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 5

INSTRUCTION MANUAL TPMS FIT
4 PRODUCT AND TECHNICAL SPECIFICATIONS
4.1 FIT TYRE PRESSURE SENSOR
FIT tyre pressure sensors monitor the pressure in your e-bike’s tyres. They transmit the tyre pressure data to your
e-bike’s display or to the FIT E-Bike Control phone app in real time via Bluetooth.
FIT AV-Schrader tyre pressure sensor FIT SV-Presta Sclaverand tyre pressure sensor
4.2 PROPER USE
All checklists and instructions for actions in these operating instructions must be met.
Only use original FIT tyre pressure sensors which the manufacturer has approved for your e-bike.
Tyre pressure sensors are designed to measure tyre pressure only and must not be used for other purposes.
4.3 IMPROPER USE
Improper use refers to use which is not described under proper use or goes beyond proper use.
4.4 UPDATES
The range of functions in the components described here is extended on a continuous basis. There may be changes
in software to remedy faults or extend functions in addition to the functions shown here.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 6

INSTRUCTION MANUAL TPMS FIT
4.5 TECHNICAL DATA
4.5.1 FIT AV-SCHRADER TYRE PRESSURE SENSOR
FIT tyre pressure
sensor
AV-Schrader
Type FIT AV-Schrader tyre pressure
sensor (sensor and valve)
AV-Schrader service kit
(replacement valve)
Part no. 501244 (FIT AV-Schrader tyre
pressure sensor, 1 unit)
501229 (FIT AV-Schrader tyre
pressure sensor, 2 units)
501268 (AV-Schrader service kit)
Manufacturer Schrader
Measurement range bar Up to 8.3
Accuracy % ±1
Suitable valve AV-Schrader
Protection class IP67
Operating temperature °C -10 up to +40
Storage temperature °C -20 up to +50
Battery life (battery
cannot be replaced)
Min. 5 years
Weight about kg 0.021
Type Part no. Manufacturer Schrader Measurement range bar Up to 8.3 Accuracy Suitable valve SV-Presta Sclaverand
Protection class IP67 Operating temperature °C Up to +40 Storage temperature °C Up to +50 Battery life (battery
cannot be replaced) Min. 5 years Weight about kg
4.5.2 FIT SV-PRESTA SCLAVERAND TYRE PRESSURE SENSOR
FIT tyre pressure
sensor
SV-Presta Sclaverand
Type FIT SV-Presta Sclaverand tyre
pressure sensor (sensor and valve)
SV-Presta Sclaverand service kit
(replacement valve)
Part no. 501105 (FIT SV-Presta Sclaverand
pressure sensor, 1 unit)
501228 (FIT SV-Presta Sclaverand
tyre pressure sensor, 2 units)
501267 (SV-Presta Sclaverand
service kit)
Manufacturer Schrader
Measurement range bar Up to 8.3
Accuracy % ±1
Suitable valve SV-Presta Sclaverand
Protection class IP67
Operating temperature °C -10 up to +40
Storage temperature °C -20 up to +50
Battery life (battery
cannot be replaced)
Min. 5 years
Weight about kg 0.021
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 7

INSTRUCTION MANUAL TPMS FIT
5 FITTING
CAUTION
Used seals or valve inserts which have been removed from the valve stem must not be re-used
under any circumstances. Ensure these components are always replaced by new original parts.
Damaged nuts, valve mounts or stems must not be re-fitted under any circumstances. Ensure
these components are always replaced by new original parts.
NOTICE
Release air from the tyre before fitting.
Fit and / or service the product with the hand tool indicated in the installation instructions.
5.1 FIT AV-SCHRADER & FIT SV-PRESTA SCLAVERAND TYRE PRESSURE SENSOR
Remove the existing valve cap and valve insert.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 8

INSTRUCTION MANUAL TPMS FIT
Fit the new valve.
Fasten the new valve into place. When fitting on tubeless tyres, ensure that the valve rim nut is firmly fastened.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 9

INSTRUCTION MANUAL TPMS FIT
Attach the sensor housing as shown in the image.
Attach the nut.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 10

INSTRUCTION MANUAL TPMS FIT
Pump up the tyres.
Fasten the valve insert.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 11

INSTRUCTION MANUAL TPMS FIT
Put on the valve cap.
5.2 FILLING WITH TUBELESS SEALANT
The entire sensor unit must be removed from
the valve stem and the valve must be
unscrewed before the tyre is filled with
tubeless sealant through the valve stem.
Do not fill the tyre sealant through the sensor
valve without removing the sensor and the
valve unit.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 12

INSTRUCTION MANUAL TPMS FIT
6 OPERATION
6.1 INITIAL OPERATION
Connect your e-bike to the FIT E-Bike Control app.
Select the Tyre pressure menu option.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 13

INSTRUCTION MANUAL TPMS FIT
Select +to add a new tyre pressure sensor.
Follow the instructions in the FIT E-Bike Control app.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 14

INSTRUCTION MANUAL TPMS FIT
Select the wheel where the tyre pressure sensor which you wish to connect
is located and press on NEXT.
Follow the instructions in the FIT E-Bike Control app.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 15

INSTRUCTION MANUAL TPMS FIT
Position the QR code for the tyre pressure sensor which you wish to connect
within the green corners.
Connection will proceed as soon as the QR code is detected.
The app will now search for the tyre pressure sensor.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 16

INSTRUCTION MANUAL TPMS FIT
Congratulations! You have successfully added the tyre pressure sensor.
Follow the instructions in the FIT E-Bike Control app.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 17

INSTRUCTION MANUAL TPMS FIT
Repeat the same steps to add
the second tyre pressure sensor.
You can now set the minimum and target pressures for both wheels.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 18

INSTRUCTION MANUAL TPMS FIT
Use -and +to set the required target pressure and press OK to save the set-
ting.
Use -and +to set the required minimum pressure and press OK to save the
setting.
Repeat the process for the other wheel.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 19

INSTRUCTION MANUAL TPMS FIT
You can use the Measurement unit menu option to select whether the pres-
sure gauge displays the pressure in PSI or bars.
Select the preferred unit and press OK to save the setting.
6.2 DISPLAY AND SETTINGS
6.2.1 FIT DISPLAY COMFORT
DISPLAY
Once the tyre pressure sensors are connected, you can display the current
values for the front and rear wheels by pressing on the selector button (DRIVE
sub-screen 2) in the Drive menu.
The following warning will be shown on the display if tyre pressure falls below
the minimum level.
FIT_Manual_Wheel_set_Tire_pressure_sensor_V1_en | Version 01 | 19.08.2022 20