FitLux 9950 User manual

9950
MULTIGYM

INDEX:
IMPORTANT NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 1
IMPORTANT SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 2
DRAWING OF MAIN BODY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 3
EXPLODED DRAWING O F MAIN BODY . . . . . . . . . . . . . . . . . . . . . . P.4-5
ASSEMBLY PARTS LIST OF MAIN BODY . . . . . . . . . . . . . . . . . . . . . P.6- 8
MAIN BODY ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . P. 9 - 16
DRAWING OF MAIN BODY & BENCH / VKR . . . . . . . . . . . . . . . . . . P. 17
EXPLODED DRAWING OF BENCH & VKR . . . . . . . . . . . . . . . . . . . . P.18
ASSEMBLY PARTS LIST OF BENCH & VKR . . . . . . . . . . . . . . . . . . P.19-20
DRAWING OF MAIN BODY , BENCH /VKR & LEG PRESS . . . . . . P.23
EXPLODED DRAWING OF LEG PRESS . . . . . . . . . . . . . . . . . . . . . . P.24
ASSEMBLY PARTS LIST OF LEG PRESS . . . . . . . . . . . . . . . . . . P.25 - 26
LEG PRESS ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . P. 27 - 31
DRAWING OF WHOLE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 32
WORKOUT CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 33
P.21 - 22
VKR & BENCHASSEMBLYINSTRUCTIONS . . . . . . . . . . . . . . . . .

BOLT LENGTH INDICATOR
NOTE: Bolt lengths are manufactured in metric(mm) so imperial length (inches) is
approximate. eg. 65mm = 2-1/2"
IMPORTANT NOTICE:
Read the instructions carefully before beginning installation. Thank you for choosing this unit for
muscular activity. For your safety and benefit, read this manual carefully before installing the
equipment. We are committed to providing you complete satisfaction. If you have any questions, or
find any parts missing or damaged, Or, should there be doubt in the assembly, please contact with
the store that you buy the unit from. We guarantee you complete satisfaction through immediate
assistance from our company.
mm
inch
IN-LINE WITH UNDERSIDE OF HEAD
1

IMPORTANT SAFETY WARNINGS
PRECAUTIONS
This exercise equipment is manufactured for use in perfect safety. However, certain precautions
should be applied whether you operate a piece of equipment. For this we recommend that you
read the entire manual before beginning installation of your equipment. In particular, read the
following safety precautions:
1. Keep children and pets out of the reach of the equipment in any moment. Do not leave children
unattended in the same room with the machine.
2. Only one person at a time should use the equipment
3. If you experience dizziness, nausea, chest pain, or any other abnormal symptoms, stop exercising
immediately and consult a physician.
4. Place the machine on a flat free surface. Do not use the equipment outdoor or near water or
external parties.
5. Keep your hands free of all removable parts.
6. Always wear appropriate clothing for exercise.
Do not use clothes or clothes that can be caught in the equipment. Wear aerobic shoes is
also required when using the machine.
7. Use the machine only for its intended use as described in this manual.
Do not use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. People with disabilities should not use the machine without a qualified person or physician to
accompany them.
10. Before using the equipment for exercise, always do stretching exercises for proper warm-up.
11. Never operate the equipment if it is not working properly.
12. A spotter is recommended during exercise.
13. Maximum User Weight: 150 kg
14. Rub two Guide Rods (k) with a rag and light oil or WD-40. This lubrication will reduce the
friction of the stems and make the weight stacks sliding up and down freely. Repeat this
procedure in the first months of installation to ensure that the rods are kept moist and
lubricated to work properly.
IMPORTANT NOTICE:
BEFORE STARTING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS
ESPECIALLY IMPORTANT FOR INDIVIDUALS AGED OVER 35 YEARS OLD OR PEOPLE WITH
PRE-EXISTING HEALTH PROBLEMS.
READ ALL INSTRUCTIONS BEFORE USING ANY OF GYM EQUIPMENT. THE HYPER-
EXTENSION DOES NOT ASSUME LIABILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE ARISING FROM THE USE OF THIS PRODUCT.
2

DRAWING OF MAIN BODY
3

4
8
13 63
13 63
13 63
13 63
2
4
12
18
2
4
1
2
2
4
H
4
9
I
19
17
17
72
2
8
8
10
F
22 2
2
4
2
4
2
6
4
2
2
10
1
27
16
28
7
7
P
5
A
C
E
D
5
4
4
4
4
4
10
2
2
2
2
2
6
2
2
1
1
1
1
5
5
33
33
38
35
14 32
RU
17
17
17
20
20
17
22
22
Q
33
33
38
38
34
37
36
36
2
S
T
28
12
28
28
28
20
20
20
20
20
31
31
29
29
O
18
4
11 J
4140
57
40
2
4
6
17 17
V
2
1
X
33
33
38
35
38
28
28
39
39
W
51
O
45
45
9
4
45
4
37
45 4
18
18
11
30
60
64
60
30
60
60
17
17
26
45 4
18
18
11
EXPLODED DRAWING O F MAIN BODY

5
10
2
2
15
15
16
G
4
4
Z
4
9
I
22
22
2
4
4
K
20
20
21
20
23
22
22
17
17
31
20
20
20
M
23
22
L
25
25
14
14
24
24
N
Y
B
C
2
2
1
5
5
2
2
2
2
42
42
58
58
59
42
42
43
44
3
62
56
3050MM
48
1090MM
49
3470MM
50
5000MM
51
54
45
55
45
37
4
45
45
61
37
37
4
4
46
47
4
2
48
51
53
43
52 56
64

B
C
E
D
N
A
O
M
L
K
F
IJ
G
H
Y
P
Z
Q
U
V
R
S
T
X
W
MAIN POLE
LEG EXTENSION SUPPORT
CHEST PRESS PIPE
BACK PAD
BACK PAD
SEAT PAD
SEAT PAD
SUPPORT TUBE
END BASE BRACE
CENTER BASE BRACE
SIDE BASE BRACE
SEAT SUPPORT BRACE
SEAT SUPPORT TUBE
FITTING PLATE
LAT PULL BAR
LEG EXTENSION TUBE
SEAT SUPPORT TUBE
PRESS HOLDER
LEG EXTENSION BRACE
TOP CROSS BRACE
TOP CROSS BRACE
PEC DECK ARM(RIGHT)
PEC DECK ARM(LEFT)
U BRACKET ADJUSTING BRACKET
TOP CROSS BEAM
ASSEMBLY PA RT S LIST OF MAIN BODY
6

5/8"x20h
M8X16L
32
31
33
17
30
29
27
26
25
24
28
23
22
21
20
19
18
1
16
15
14
13
11
10
9
8
12
7
6
5
4
3
2
3/8"X76L
30X70
30X70
30X60
50X50
40X80
3/8"X89L
3/8"X82L
3/8"X128L 5/8"X254L
5/8"X165L
3/8"
5/8"
3/8"XΦ19X1.0t
PIN FOR WEIGHT STACK
PIN
QUICK PIN
PLASTIC INNER BUSHING
PLASTIC INNER BUSHING
PLASTIC INNER BUSHING FORM PAD
FORM PAD
CURLING BAR
GRIP COVER
METAL BUSHING
METAL BUSHING
CAP
CAP
CAP
CHAIN
CAP
PLATE
Φ8.2xΦ16X1.5t
Φ10.5XΦ35X3.0t
3/8"
3/8"X70L
M6X16L
M8X45L
7
ASSEMBLY PA RT S LIST OF MAIN BODY

3050MM
3470MM
1/2"
M6
1/2"
5000MM
6MM
8MM
1/2"
1090MM
3/8"
1"
1/2"X76L
3/8"X1/2"
23X53
3/8"X38L
3/8"X32L
Φ13XΦ44X3.0t
41
40
39
38
37
36
35
34
59
62
64
63
61
58
57
56
60
55
54
53
52
48
47
46
45
43
42
44
49
51
50
INNER PIPE
ROLLER PIPE
CAP
CAP
METAL BUSHING
TOP PLATE
WEIGHT PLATE
PLATE
GUIDE PIN
GUIDE ROD
SNAP HOOK
SNAP HOOK
FLOATING PULLEY BLOCK
RUBBER WEIGHT
STACK BOTTOM
SAFETY COVER
LOW PULL BAR
PULLEY
ROD
CABLE
CABLE
CABLE
8
ASSEMBLY PA RT S LIST OF MAIN BODY

MAIN BODY ASSEMBLY INSTRUCTIONS
STEP 1:
1. Put CAP (5) onto END BASE BRACE
(C) and SIDE BASE BRACE (E).
2. Attach MAIN POLE (A), SUPPORT
TUBE (B) and END BASE BRACE (C)
onto CENTER BASE BRACE (D) by
screwing on parts ( 1,2,4 & 10 )
provided.
3. Put SIDE BASE BRACE (E) onto
CENTER BASE BRACE (D), securing
with parts (1,2, 4 & 6) provided.
NOTE: Please DO NOT put on
PLATE (6) if this Home Gym
equipped with LEG PRESS
ATTACHMENT.
5
A
B
C
C
E
D
5
4
4
4
4
4
10
2
2
2
2
2
2
2
6
2
2
1
11
1
1
5
5
5
5
9

19
17
17
22
22
22
72
2
2
2
2
2
2
2
1
1
2
2
10
10
8
8
2
2
4
4
4
13
13
13
13
15
15
16
63
63
63
63
4
4
4
4
4
18
12
18
11
4
4
4
8
8
9
9
10
F
B
G
H
D
E
C
A
Z
J
K
II
STEP 2:
1. Put TOP CROSS BEAM (F) on top of MAIN POLE (A), securing with parts (2, 4,7 & 10) provided.
Connect TOP CROSS BEAM (F), SUPPORT TUBE (B) and TOP CROSS BRACE (K) by screwing on
parts (2,4 & 8) provided.
2. Put U BRACKET (I) onto SUPPORT TUBE (B), securing with parts (4 & 9).
3. Attach BACK PAD (Z) onto SUPPORT TUBE (B) by screwing on parts (13 & 63) provided.
4. Attach SEAT SUPPORT BRACE (G) onto
SUPPORT TUBE (B), securing with
parts (2,4,8 & 10) pro-
vided. Insert QUICK
PIN (16) into SEAT
SUPPORT BRACE
(G), and put on
PLASTIC INNER
BUSHING (15)
from top and bottom sides.
5. Put LEG EXTENSION BRACE (H) onto
CENTER BASE BRACE (D) by screwing
on parts (1,2 & 4) provided.
6. Insert METAL BUSHING (18) into
MAIN POLE (A) left and right
sides, then attach ADJUSTING
BRACKET (J) onto MAIN POLE
(A), securing with parts (4 &
11) through METAL
BUSHING (18) as
drawing shown.
10

22
2
2
2
6
10
1
27
28
12
28
28
21
28
20
20
20
31
29
16
28
7
7
4
4
25
25 23
23
22
22
22
17
17
31
20
20
20
20
20
20
14
14
24
24
4
P
N
G
A
K
F
H
Y
L
M
O
STEP 3:
1. Attach LEG EXTENSION SUPPORT (P) onto LEG EXTENSION BRACE (H) and MAIN POLE (A) by
screwing on parts (1,2,4,7 & 10) provided. Insert into PLASTIC INNER BUSHING (27), then screw on
QUICK PIN (16). Put on CAP (28) on top of LEG EXTENSION SUPPORT (P).
2. Insert METAL BUSHING (20) into the holes on top of PRESS HOLDER (O), then have PRESS HOLDER
(O) attached on TOP CROSS BEAM (F), securing with parts (29 & 31) as drawing shown. Insert PIN
(12) into PRESS HOLDER (O) as drawing shown.
3. Insert METAL BUSHING (20) into the holes on top of PEC DECK ARM (L & M), then attach the PEC
DECK ARMS onto TOP CROSS BRACE (K) by
screwing on parts (19 & 21) provided.
NOTE: Please DO NOT tighten rmly yet.
4. Insert PLASTIC INNER BUSHING (22) into
the bottom of PEC DECK ARM (L & M) ,
then put on FOAM PAD (23) left and right sides.
5. Put SEAT PAD (Y) on SEAT SUPPORT TUBE (N), securing
with parts (14 & 25) then put on END CAP (24). Have the
assembled SEAT SUPPORT TUBE (N) inserted into SEAT
SUPPORT BRACE.
NOTE: Select the holes with proper height on SEAT SUPPORT BRACE (G) to
secure with QUICK PIN (16) provided.
11

J
17
17
17
20
20
20 20
20
29
33
33
33
33
38
38
38
34 37
36
36
2
35
14 32
31
17
22
22
R
S
T
P
O
U
Q
STEP 4:
1. Insert METAL BUSHING (20) into PRESS HOLDER (O) first, and then attach CHEST PRESS PIPE (Q)
onto PRESS HOLDER (O) by screwing on parts (29 & 31) provided.
NOTE: DO NOT tighten the bolts rmly yet.
Insert PLASTIC INNER BUSHING (22) and put on GRIP COVER (17).
2. Put SEAT PAD (S) onto SEAT SUPPORT TUBE (T), securing with parts (2 & 37) provided. Have the
assembled SEAT SUPPORT TUBE (T) inserted into LEG EXTENSION SUPPORT (P).
NOTE: Select the holes with proper height on SEAT SUPPORT TUBE (T) to secure with
QUICK PIN (16). Then put on CAP (36).
3. Insert INNER PIPE (34) into SEAT SUPPORT TUBE (T), and put on CAP (38) on both sides. Put on
FOAM PAD (33) right and left sides.
4. Insert FITTING PLATE (U) into the pipe of ADJUSTING BRACKET (J), then attach BACK PAD ?on
FITTING PLATE (U) by screwing on parts (14 & 32) provided. Insert ROLLER PIPE (35) into the
bottom of ADJUSTING BRACKET (J). Insert into CAP (38) and put
on FOAM PAD (33) as drawing shown.
12

STEP 5:
1. Insert METAL BUSHING (39) into the top of LEG EXTENSION TUBE (W), have LEG EXTENSION TUBE (W)
attached onto the top of LEG EXTENSION SUPPORT (P), securing with parts (40, 41 & 57) provided.
NOTE: DO NOT tighten the bolts rmly yet.
2. Insert ROLLER PIPE (35) into LEG EXTENSION TUBE (W), put on CAP (38) and FOAM PAD (33). Insert CAP
(28) into both sides of LEG EXTENSION TUBE (W) as drawing shown.
3. Insert GUIDE ROD (59) into SIDE BASE BRACE (E), then slip on RUBBER WEIGHT STACK BOTTOM (62).
NOTE: If this Home Gym equipped with VKR (VERTICAL KNEE RAISE) attachment, then prior to
inserting the GUIDE ROD (59), you have to attach VKR BASE BRACE (C2) onto SIDE BASE
BRACE (E) by screwing on parts (1,2,4 & 10) provided rst.
4. Slip WEIGHT PLATE (44) onto GUIDE ROD (59) one by one, then the TOP PLATE (43). Insert ROD (52) into
the top hole on GUIDE PIN (56), then insert GUIDE PIN (56) into the central hole on TOP PLATE (43) to
secure.
NOTE: Insert PIN (3) into different holes on WEIGHT STACK to select the proper weights for your
workout.
5. Attach TOP CROSS BRACE (X) onto TOP CROSS BEAM (F), securing with parts (1,2,4 & 6) provided.
NOTE: If this Home Gym quipped with LEG PRESS
ATTACHEMENT, there won,t be PLATE (6) is available.
6. If this Home Gym equipped with SAFETY COVER (58),
please install SAFETY COVER (58)
between TOP CROSS
BRACE (X) and SIDE
BASE BRACE (E),
securing with
parts (2 & 42)
provided.
51
53
43
52 56
2
22
2
2
2
2
42
33
33
38
35
38
28
28
57
39
39
41
40
40
43
44
3
62
42
58
59
58
42
42
21
4
6
X
E
W
P
56
F
13

STEP 6:
CABLE AND PULLEY ASSEMBLY INSTRUCTION:
Start threading with CABLE (48).
1. Refer to Drawing (A1 & A2), have one end of CABLE (48) screwed on the bolt on left PEC DECK
ARM (M).
2. Thread CABLE (48) through the pulleys in order of P1-P2 then up to P3.
NOTE: 1) Cable and pulleys must be threaded and assembled at the same time.
2) Assemble and attach pulleys as per each exploded drawing show: A3 & A4
3. Have another end of CABLE (48) screwed on the bolt on right PEC DECK ARM (L) as Drawing (A1
& A2) shown.
45
45
37
37
3/8"X38L
3/8"X38L
4
4
B
A3
46
47
L, M
4
2
48
3/8"X32L
A2
48
A1
I
51
A4
(P2)
48
A1
49
45
45
61
37
37
3/8"X38L
3/8"X38L4
4
3050MM
48
A2
A3(P1, P3)
A4
Start End
14

STEP 7:
CABLE AND PULLEY ASSEMBLY INSTRUCTION:
A. Start threading with CABLE (50): Refer to Drawing (A1), have CABLE (50) head (without the ball
over) threaded through Pulley (P9).
NOTE: Cable and pulley must be threaded and assembled at the same time.
B. Start threading with CABLE (49):
1. Refer to Drawing (A6), thread CABLE (49) head (without the ball over) through the pulleys in
order of: P1-P2-P3-P4-P5-P6-P7-P8
NOTE: 1) Cable and pulleys must be threaded and assembled at the same time.
2) Assemble and attach pulleys as per each exploded drawing shown: A6, A5,
A4, A2 & A3
2. Have CABLE (49)
end connected with
CABLE (50) end by
hooking on both
ends of CHAIN (30)
with SNAP HOOK (60)
as Illustration (A7)
shown.
NOTE: By hooking on
the different posi-
tions on CHAIN (30)
to adjust Cable
length you need.
I
45
4
18 18
H
9
3/8"X70L
A5
4
45
B
11
18
3/8"X82L
A1
45 W
4
9
18
18
3/8"X70L
A6
3/8"X38L
45
55
45
37
4
A3 A4
45
45
45
4
4
44
37
37
D
3737
3/8"X38L
A2
50
64
54
9
418
18
A45
3/8"X70L
55
61
49
49
1090MM
49 3470MM
50
A1
(P9)
A2
(P8)
(P7)
A2
(P6)
A2
(P4)
A3
(P5)
A7
A4
(P3)
A5
(P2)
17
17
26
30
60
60
A6
(P1)
30
60
50
49 60
A7
60
60
30
Start
Start
End
End
15

STEP 8:
CABLE AND PULLEY ASSEMBLY INSTRUCTIONS:
Start threading with CABLE (51):
1. Refer to Drawing (A1), thread CABLE (51) head (without the ball over) through the pulleys in
order of: P1-P2-P3-P4-P5-P6-P7-P8
NOTE: 1) Cable and pulleys must be threaded and assembled at the same time.
2) Assemble and attach pulleys as per each exploded drawing shown: A1, A2,
A3, A4 & A6
2. Have CABLE (51) end screwed on top of GUIDE PIN (56) through WASHER (53) and TOP PLATE
(43), securing with nut on CABLE (51) head as Illustration (A5) shown.
NOTE: 1. Check
all connection
portion and
adjust to
secure.
3. Retighten all
fasteners after
1-2 weeks use.
Recheck from
time to time to
ensure they
are tightened
firmly.
17
17
V
51
48
50
A6
49
4
4
45
45
18
F
18
18
18
9
9
3/8"X70L
A1
4
45
O
18
18
93/8"X70L
A2
4
4
45 45
18
A
18 9
37
3/8"X70L
3/8"X38L
A3
4
X
45
37
3/8"X38L
A4
51
A6
A1
(P1)
A1
(P2)
A3
(P4)
A3
(P6)
(P7)
A2
(P3, P5)
A4(P8)
A5
64
A5
51
53
43
52 56
5000MM
51
Start
End
16

DRAWING OF MAIN BODY & BENCH / VKR
17

5
5
44
4
4
2
2
39
40
57
S2
41 40
10
2
28
38
38
17
17
2
2
2
1
1
9
1
10
B2
E2
C2
D2
M2
M2
A2
L2
L2
O2
O2
F2
4
2
2
1
2
1
2
1
4
2
4
4
10
28
2
1
H2
T2
R2
R2
Q2
Q2
28
17
17
28
R2
14
14
2
2
14
I2
K2 K2
J2
P2
P2
38
38
G2
N2
42
EXPLODED DRAWING OF BENCH & VKR
18