Impex IGS-8858 User manual

IRON GRIP STRENGTH
WEIGHT BENCH
IGS-8858
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: [phone] Fax [phone]
www.impex-fitness.com
[email protected]
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
IGS 8858
Retain This
Manual for
Reference
07/25/06
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 6
EXPLODED DIAGRAM.................................................................................... 11
PARTS LIST..................................................................................................... 12
WARRANTY..................................................................................................... 13
ORDERING PARTS.......................................................................................... 13
BEFORE YOU BEGIN
Thank you for selecting the IRON GRIP STRENGTH IGS-8858 BENCH by
IMPEX®INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 600 lbs.
15. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Cross Brace. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown
3

HARDWARE PACK
4

HARDWARE PACK
5

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Left & Right Upright Beam (# 1 & #2) by a Cross Brace (#4) in the mid span.
Secure them with M10 x 3 ¾” Carriage Bolts (#40), one 5 ½” Bent Bracket (#16), two ∅¾”
Washers (#49), and two M10 Aircraft Nuts (#52) on each side.
B.) Insert two Crutches (#6) into the top openings on the top of Left & Right Upright Beams.
Insert two M18 Lock Knobs (#31) through selected holes to obtain desired height.
C.) Place the Backrest Adjustment Bar (#5) on the selected slot on the Upright Beams to
obtain the desired backrest incline. DIAGRAM 1
6

STEP 2 (See Diagram 2)
A.) Attach the front of Main Seat Support (#3) to the Front Post (#9). Secure it with two
M10 x 3 1/8” Carriage Bolts (#41), one 6 ¼” Bent Bracket (#18), two Ø ¾” Washers
(#49), and two M10 Aircraft Nuts (#52).
B.) Attach the Main Seat Support to the top of Front Post. Secure it with two M10 x 3 1/8”
Carriage Bolts (#41), one 4 ¾” Bent Bracket (#17), two Ø ¾” Washers (#49), and two
M10 Aircraft Nuts (#52).
C.)Attach the Main Seat Support to the Cross Brace (#4). Secure it with two M10 x 3 1/8”
Carriage Bolts (#41), two Ø ¾” Washers (#49), and two M10 Aircraft Nuts (#52) from
top. Secure it with two M10 x 3 3/8” Carriage Bolts (#58), one 4 ¾” Bent Bracket (#17),
two Ø ¾” Washers (#49), and two M10 Aircraft Nuts (#52) from the side.
DIAGRAM 2
7

STEP 3 (See Diagram 3)
A.) Attach the Backrest Incline Support (#13) to the side-holes on the two Backrest Supports
(#12). Align the holes. Secure it with one M12 x 7 ¼” Allen Bolt (#43), two Ø ¾” Washers
(#49), and one M12 Aircraft Nut (#52).
B.) Attach the holes on the end of the Backrest Supports (#12) to the pivot on the Main Seat
Support (#3). Attach the two ends of the Seat Support (#11) to the two holes on end of
Backrest Supports. Align the holes. Secure them together with one M12 x 7 5/8” Allen Bolt
(#42), two Ø 1” Washers (#48), and one M12 Aircraft Nut (#51).
C.) Do not over tighten the Nuts and Bolts. Make sure the Backrest Supports and Backrest
Incline are able to swivel.
D.) Place the other ends of Seat Support onto the Main Seat Support. Use a 4” Lock Pin (#54)
through the hole on Seat Support under the Main Seat Support to secure the incline of the
Seat.
E.) Insert the Arm Curl Stand (#7) into the opening on Main Seat Support. Use a M10 Lock
Knob (#32) to lock the Stand at desired height. DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Attach the Backrest Board (#20) to the Backrest Supports (#12). Secure it with four M8 x 1
5/8” Allen Bolts (#45) and four Ø 5/8” Washers (#50).
B.) Place the Seat (#21) onto the Seat Support (#11). Secure it with four M8 x 1 5/8” Allen
Bolts (#45) and four Ø 5/8” Washers (#50).
C.) Attach the Arm Curl Pad (#22) to the Arm Curl Bracket (#55). Secure it with two M8 x 5/8”
Allen Bolts (#46) and two Ø 5/8” Washers (#50).
D.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#7). Insert the M8 x 3
½” Allen Bolt (#56) through the open track on the Arm Curl Stand and the holes on the
Arm Curl Bracket. Secure the Bolt with two Ø 5/8” Washers (#50) and one M8 Aircraft Nut
(#57). Do not over tighten the Nut and Bolt. The Bolt needs to be able to slide on the track
freely. DIAGRAM 4
9