Fixturlaser GO Pro User manual

MANUAL
Fixturlaser GO Pro user`s

CONTENT
Fixturlaser GO Pro Manual 2nd edition
September 2011
Introduction
1.1
Declaration of Conformity
2.1
Safety
3.1
Care
4.1
Main Menu
5.1
Shaft Alignment Horizontal
Machines
6.1
Shaft Alignment Vertical
Machines
7.1
Machine Defined Data
8.1
Softcheck
9.1
Target Values
10.1
Memory Manager
11.1
Global Settings
12.1
Display Unit GO Pro D
13.1
Wireless Transceivers
14.1
Technical Specification
GO Pro D
15.1
Technical Specification M1/S1
16.1

Fixturlaser GO Pro Manual 2nd edition
September 2011

Fixturlaser GO Pro Manual 2nd edition
1.1
1INTRODUCTION
Congratulations on your choice of the
Fixturlaser GO Pro!
We are convinced that you have made
the right decision and we hope the
system will meet, and even exceed,
your expectations.
It is important that you read the
sections about safety and care before
you proceed with your first
measurement.
The purpose of this manual is to guide
you through the different procedures
and operations of the hardware and
software. Since machine installations
and setups are often different from each
other, we have focused this manual on
measurement principles and how to
handle the system.
The manual describes applications,
functions and equipment that may be
available in a Fixturlaser GO Pro
system; the ones that are available in
your specific system depend upon which
application packages and accessories
you have selected.
We wish you many successful
measurements!

Fixturlaser GO Pro Manual 2nd edition
1.2
END USER LICENSE AGREEMENT
The rights to use the software in this
product are offered only on the
conditions that you agree to all the
terms stated below, i.e. the end user
agreement. By using this product you
agree to be bound by this agreement. If
you do not accept this agreement your
sole remedy is to return the entire
unused product, hardware and software,
promptly to your place of purchase for a
refund.
The user is granted a single license to
use the software contained in this
product. Use is only permitted on the
hardware it has been installed on at the
time of purchase. The software may not
be removed from the hardware.
The software contained in the system is
the property of Elos Fixturlaser AB, any
copying or redistribution is strictly
prohibited.
Modifying, disassembling, reverse
engineering or decompiling the system
or any part thereof is strictly prohibited.
Disclaimer of warranties: To the
maximum extent permitted by
applicable law, Elos Fixturlaser AB and
its suppliers provide the software
contained in this product „as is‟ and with
all faults, and hereby disclaim all other
warranties either expressed, implied or
statutory.
Limited liability: No liability shall exceed
the price of the product, and the sole
remedy, if any, to any claim shall be a
right of return and refund.
Elos Fixturlaser AB or its suppliers shall,
to the maximum extent permitted by
applicable law, not be liable to any
indirect, special, incidental, punitive,
and consequential damages arising from
the use of the system or any part
thereof, authorized or unauthorized.

Fixturlaser GO Pro Manual 2nd edition
2.1
2DECLARATION OF
CONFORMITY
In accordance with the EMC Directive
2004/108/EC, the Low Voltage Directive
73/23/EEC, including amendments by
the CE-marking Directive 93/68/EEC &
EC directives RoHS, 2002/95.
Type of equipment
Alignment System
Brand name or trade mark
Fixturlaser GO Pro
Type designation(s)/Model no(s)
1-0875 Fixturlaser GO Pro
Manufacturer’s name, address,
telephone & fax no
Elos Fixturlaser AB
Box 7
SE-431 21 Mölndal
Sweden
Tel: [phone]
Fax: [phone]
The following standards and/or technical
specifications, which comply with good
engineering practice in safety matters in
force within the EEA, have been applied:
Standard/Test report/Technical
construction file/Normative
document
Emission: EN 61000-6-3:2007.
Immunity: EN 61000-6-2:2005, EN
61000-4-2, -3.
ISO9001:2008 Ref. No/ Issued by: DNV
Certification AB Certification No. 2009-
SKM-AQ-2704 / 2009-SKM-AE-1419.

Fixturlaser GO Pro Manual 2nd edition
2.2
The laser is classified in accordance with
the International Standard IEC-60825-
1:2007,
USA FDA Standard 21 CFR, Ch 1, Part
1040.10 and 1040.11 except for
deviations pursuant to laser notice No.
50, dated June 24, 2007.
The wireless device complies with Part
15 of the FCC Rules. Operation is
subject to the following two conditions;
(1) this device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Additional information
The product was CE-marked in 2010.
As manufacturer, we declare under our
sole responsibility that the equipment
follows the provisions of the Directives
stated above.
Date and place of issue
Mölndal 2010-09-30
Signature of authorized person
Hans Svensson, Managing Director

Fixturlaser GO Pro Manual 2nd edition
3.1
3SAFETY
Retain and follow all product safety and
operating instructions. Observe all
warnings on the product and in the
operating instructions.
Failure to observe the safety pre-
cautions and operating instructions can
cause bodily injury, fire, and damage to
the equipment.
Do not disassemble, modify or use the
equipment in other ways than explained
in the operating instructions. Fixturlaser
will not accept any liability for such use.
LASER PRECAUTIONS
Fixturlaser GO Pro uses laser diodes
with a power output of < 1.0 mW. The
laser classification is Class 2.
Class 2 is considered safe for its
intended use with only minor pre-
cautions required. These are:
Never stare directly into the laser
transmitter.
Never shine the laser directly into
anyone else‟s eyes.

Fixturlaser GO Pro Manual 2nd edition
3.2
Your system complies with the
requirements in:
SS-EN-60825-1-1994
British Standard BS 4803 Parts 1
to 3
Deutsche Industrie Norm DIN JEC
76 (CO) 6
USA FDA Standard 21 CFR, Ch 1,
Part 1040.10 and 1040.11
POWER SUPPLY
Fixturlaser GO Pro is powered by three
1.5V LR-14 (C) Alkaline batteries or by
corresponding 1.2V NiMH HR-14
Rechargeable Nickel Metal Hydride cells.
Only use high performance alkaline
batteries.
Remove batteries when the system is
stored for prolonged periods of time.
WARNING!
USE OF ANY OTHER
BATTERIES THAN THOSE
SPECIFIED BY FIXTURLASER
WILL CAUSE SEVERE
DAMAGE TO THE DISPLAY
UNIT AND CAN CAUSE RISK
FOR PERSONAL INJURY!