JASON Hydrotherapy Home Spa Edition Air-Whirlpool User manual

Jason InternatIonal, Inc.
8328 MacArthur Drive • North Little Rock, AR 72118 • www.jasoninternational.com
501.771.4477 • Fax: [phone] • Cust. Service: 800.255.5766
PAGE T.21
DATE 07/09
Supercedes 06/08
Home Spa Edition Air-Whirlpool
Digital Control Keypad with Remote Control
FEATURES
KEYPAD CONTROLS
All functions of the Jason Home Spa bath can be
conveniently operated with either one of the two
Home Spa digital keypad controls which control the
operation of the three speed whirlpool pumps, the air
blower, underwater mood lights, and the jetted neck
pillows. The dual keypads are used to run individual
pumps and jetted neck pillows. The same blower and
lights are controlled from both keypads.
WHIRLPOOL ON/OFF (PUMP ICON)
To control the operation of the whirlpool pump motor,
press and hold for each setting, High, Medium, Low,
or Off. A 20 minute decreasing timer will be initiated
when the pump motor starts. Press and release the
Pump icon once to display the current pump setting.
The Pump icon lights when the water is at operating
level and the LCD displays “System Ready”. The
LCD will display “Pump Off”, “Pump High”, “Pump
Medium”, or “Pump Low” when the key is pressed.
It also toggles between Temperature (+/- 5°F) and
Timer at 5 second intervals. “Low Water” is displayed
if no water is detected. (Displays for 5 seconds.).
LED LIGHT (LIGHT ICON)
Hold the key for less than two (2) seconds to turn
the lights Off or On. Hold the key for more than two
(2) seconds to change color modes. The Light icon
should remain lit as long as the bath is connected to
a power supply. This function has a two-hour timer
and remembers the last mode. The LCD displays
“Light On” or “Light Off” while the key is pressed for
less than two (2) seconds; “Light Cycle” is displayed
if pressed for more than two (2) seconds.
JETTED NECK PILLOW (“P” ICON)
To control the operation of the jetted neck pillow,
press and hold for each setting, you can set for a
constant flow on both jets, a pulsing flow on both
jets, or a pulsing alternating flow between jets.
Press and release the Pillow icon once to display
the current pillow setting. The Pillow icon will light
whenever the pump is running. The solenoids will
open for two (2) minutes to drain during the purge
cycle countdown. The LCD will display “Pillow On”,
“Pillow Pulse1”, “Pillow Pulse2”, or “Pillow Off” while
the key is pressed.
OPTION (“O” ICON)
This key is reserved for future options.
BLOWER ON/OFF AND MODES
(BLOWER ICON)
To control the operation of the blower, simply press
and hold the key to change the setting to Constant,
Wave, Pulse, or Off. A 20 minute decreasing timer
will be initiated when the blower motor starts. Press
and release the Blower icon once to display the
current blower mode and speed. The LCD will
display “Const Air” and blower speed, “Wave Air”
and blower speed, or “Pulse Air” and blower speed,
IR F O R R E M O T E
B L O W E R O N /O F F , M O D E S
B L O W E R S P E E D S
J E T T E D N E C K P I LL O W
O P T IO N
P
O
L E D LIG H T
JASON
W H IR L P O O L O N /O F F , S P E E D C O N T R O L
S IG N A T U R E E D IT IO N A IR -W H IR L P O O L
S Y S T E M
R E A D Y
PAGE T.21
DATE 11/07
Supercedes 07/07

PAGE T.22
DATE 07/09
Supercedes 06/08
while the key is pressed. The time remaining on the
purge cycle is displayed after the bath has drained.
“Purge Stop” is displayed while the key is pressed
during the purge cycle. This action will terminate the
purge cycle. The mode settings will be remembered
on the next startup.
BLOWER SPEEDS (+- ICON)
Hold the key in Constant mode to go from High to Low
then release and hold again to go from Low to High.
Hold the key in Wave and Pulse mode to go from
High to Medium and Medium to High. The system
remembers the last speed setting on the next startup.
The icon will light up when the blower is running.
The LED displays blower speeds from “10” (Low)
or “55”(Med) to “99” (High) while the key is pressed.
You can reduce the auto purge idle time from 20 to
10 minutes, by pressing and holding the key for more
than 5-seconds during the purge idle period.
CUSTOMIZED SETTINGS
The 12 character LCD display can be customized
by pressing the Blower and Blower Speeds icons
simultaneously for five (5) seconds, while the system
is Off. Note: The Blower Speeds icon will not be
illuminated during this process. Use the figure to
locate the icons. A menu will be displayed to choose
the following: Purge 24, (starts the blower every 24
hours for two (2) minutes at the same time the purge
was set), Product Test Diagnostics, Temperature (F
or C), and Language (English or Spanish).
MENU INSTRUCTIONS
Use the Blower icon to scroll through the different
menu items. Use the Blower Speeds icon to change
an option. For example, press and release the Blower
icon to change from Purge 24 to Product Test, press
and release again to arrive at the Temperature option.
Press and release the Blower Speeds icon to change
the temperature display from F (Fahrenheit) to C
(Celsius).
PRODUCT TEST DIAGNOSTICS
After selecting the Product Test option from the menu,
the unit will perform a series of tests to confirm correct
installation of components. The test will begin by
displaying the configuration number, followed by the
software revision number. Next, the ISD-237 control
box will be tested to ensure proper IR communication.
The display will then test the Temperature and Low
Water level sensor (ITW-209). Next, each of the six (6)
icon buttons will begin to light. Press the illuminated
button to proceed to the next icon. After the icon
test, the pump will start for two (2) seconds on the
high setting. Lastly, the LED light unit will be tested.
If you receive and error on any of the tests, confirm
proper installation of the component to the correct
control box.
REMOTE CONTROL
Home Spa bath control system includes a waterproof
floating universal remote. It controls all bath functions
plus TV, DVD, CD, etc. which can be heard through
the Sound Immersion Transducers (4-each).
PAGE T.22
DATE 11/07
Supercedes 07/07