FLACARP FL6-RGB User manual

Thanks to the very low battery con-
sumption, the LED lamp can light for
a very long time in the low brightness
mode. So it can be used for the sh-
ing place designation.
RGB LED lamp with a receiver - FLACARP FL6-RGB
USER MANUAL P1
LED LAMP CONTROL
TIP
INTEGRATED RECEIVER FALSE ALARMS
LOW BATTERY STATUS
AUTOMATIC SHUTDOWN
SPECIFICATIONS
Thank you for purchasing the FLACARP
FL6-RGB. The lamp was created based
on the requirements of you, anglers. It is
equipped with powerful LEDs with the
possibility of adjusting the color. The in-
tegrated receiver allows you to remotely
control the lamp with up to ten FLACARP
transmitters.
Lamp can be switched ON after a bite,
after an alarm, or remotely controlled by
receiver RFX, e.g. lamp could be used like
a beacon. The distance can be up to 500
meters. You can reduce the brightness of
the LEDs so that the strong light does not
disturb you.
And the batteries? You will no longer have
to replace them! The lamp is equipped
with a powerful rechargeable Li-Ion bat-
tery. You can conveniently charge it using
a phone charger, from a car, or from any
power bank.
The lamp is designed not only for the
bivouac, but due to its 100% water resis-
tance, it can also be used as smart out-
door lighting. And when it falls into the
water, the lamp doesn‘t sink - it oats on
the surface :-)
The lamp is controlled by the green side
button.
Switching on / off
A short press of the button switches the
lamp ON, and it can be switched OFF in
the same way.
Brightness reducing
A short press of the button switches on
the lamp, and immediately following
next press of the button sets a lower
brightness level, suitable for reading, for
example. Lowering the brightness level
also extends the lighting time.
Color change
You can quickly change the color of the
LED by a double-click. The selected color
is then set as a default one after restart.
The color can be changed anytime.
Control button
Cover of the charging connector
with a strong magnet
Receiver switching on / off
by holding the button for 2 seconds.
Activation of the receiver is conrmed by
a brief ashing of the green LED, deacti-
vation by a brief ashing of the red LED.
Saving new device in memory
Hold down the button for 5 seconds
to enter the learning mode (LED light
ashes). You can now double-click to
select the color that should be lit by the
transmitter.
You can select white, red, green and blue.
The next step is the purple color - in this
step, the color already set on the bite
alarm is copied.
Save
Send a signal from the device you want to
save, that’s mean: turn ON the bite alarm,
alarm or press (short) the main button
on the receiver (while switched ON). The
device sends a signal and the LED light
save it in memory. Pairing is complete.
After saving, the learning mode is auto-
matically nished. Repeat the identical
procedure for saving other devices. If you
want to change the color of a specic
device, simply enter the learning mode
again and repeat the process. The color
of already stored device will be overwrit-
ten in memory.
Erase memory
Delete all learned devices from the
lamp’s memory. Hold down the button
for 15 seconds. A fast ashing red LED
indicates that the memory has been
erased.
The lamp reduces the false alarms.
The bite alarms turn on the light after
two or more succesive “bites” within 5
seconds. But the alarm from the mo-
tion sensor turns on the light immedi-
ately, as well as the RFX receiver control
responds immediately.
To prevent the permanently lit lamp in
the event of a false alarm, the lighting
time by a bite alarm or motion sensor
alarm is limited to 60 seconds.
Discharge of the battery is indicated
by a triple red LED brief ashing. If
the lamp does not respond at all, or
it switches OFF immediately when
switched on, it is discharged and
needs to be charged. Charge the lamp
before the rst use.
The receiver of the lamp automatically
switches OFF 24 hours after the last ac-
tivity (after the last use). This function
prevents the lamp from discharging
when it is not used for a long time in
case you forget to switch OFF the re-
ceiver function.
■LED type: RGB + white CREE®
■Battery: Li-Ion 2000mAh
■Charging: 5V / typ. 410mA
■Charging time: approx. 6 hours (from
full discharge)
■Lighting time (full brightness): up to 9
hours
■Lighting time (reduced brightness): up
to 24 hours
■Frequency: 868MHz
■Range: up to 500 meters in open space
■Operating temperature: 0 to 40ºC
■Dimensions: 136 x 36 (42) mm
■Weight: 124 g
+420 731 115 151 obchod@tfe.cz flacarp.com flacarp flacarp tfe.cz

of a radio device with the European Direc�ve RED 2014/53/EU, establishing technical requirement for radio equipment, and
the Governmental Decree No. 481/2012 Col., which is harmonized with Direc�ve 2011/65/EU, about the use of some
dangerous substances in electrical and electronical devices.
LED light listening receiver
The Declara�on has been issued under the sole responsibility of the producer.
Do you have any wishes or comments about the product? Please let us know to
tomas@tfe.cz and help to improve our products. Thank you.
TFE elektronika s.r.o.
náměstí Svobody 1509
696 81 Bzenec, ČR
+420 731 115 151
obchod@tfe.cz
The USB charging connector is located be-
low a waterproof cover with magnet. The
lamp can be charged using any mobile
phone charger with a voltage of 5V, from
any powerbank or from an auto-adapter
for mobile phones charging (5V).
The lamp can be used and charged at the
same time (subject to the above condi-
tions). Connector type is microUSB, volt-
age 5V. Charging current is about 500mA,
charging time from full discharge is about
6 hours.
Charging status indication
■Red LED indicates charging
■Green LED fully charged
The mentioned charging times and light-
ing times are indicative and depend on
the condition of the battery, the ambient
temperature and the method of use.
Connect the charger only in dry condi-
tions. The lamp cannot be charged in the
rain (unscrewed waterproof connector
cover) and at temperatures below the
freezing point, or otherwise at tempera-
tures above 40ºC. The operating and the
storage temperature must not exceed
50ºC. Do not leave the lamp in summer
months in the car on the dashboard or
behind the windows in direct sunlight. Do
not throw into re. The package include a
short USB cable and a protective case.
At the end of its service life, remove the
battery and dispose pursuant to the
Waste Act (hand over the product to a
collection point or to the manufacturer or
retailer for disposal).
The product is guaranteed for 24 months.
The legal warranty for battery life is min.
6 months.
The lamp is equipped with battery pro-
tectors and with intelligent charging for
maximum service life of the battery.
The LED lamp FLACARP FL6-RGB is de-
signed for outdoor and indoor lighting. It
is protected against rain and falls into the
water, providing all sealing elements are
tightened properly - meaning side sock-
ets and the cover of the USB connector.
The warranty does not apply to mechan-
ical damage to the lamp, to electrical
damage caused by charging using an-
other than the specied voltage. The
warranty also does not cover damage
due to water penetrating the lamp or the
charging connector, or the use contrary
to these manual.
The service and replacement of the bat-
tery is performed by the manufacturer or
a service center authorized by him.
EN1
RGB LED lamp with a receiver - FLACARP FL6-RGBUSER MANUAL
WARRANTY EU DECLARATION OF CONFORMITY
MANUFACTURER
CHARGING, SAFETY
P2
+420 731 115 151 obchod@tfe.cz flacarp.com flacarp flacarp tfe.cz
Popular Lighting Equipment manuals by other brands

Toro
Toro 30660 installation instructions

TotalPond
TotalPond UW16205 instruction manual

Clevertronics
Clevertronics L10 ARGOPRO-1200-L10POD Series Installation instruction

Lightolier
Lightolier LYTECASTER 2000LVRE1 Installation

brennenstuhl
brennenstuhl Chip LED L CN 110 IP65 operating instructions

Godox
Godox S30 instruction manual

Larson Electronics
Larson Electronics WAL-ML-2XM-3G instruction manual

Beamz
Beamz BMS24 instruction manual

HUBBELL LIGHTING
HUBBELL LIGHTING Compass CELEM installation instructions

Lightolier
Lightolier Calculite C6P30MHA specification

LEGRAND
LEGRAND WP2 LED quick start guide

Sensio
Sensio Polar IP65 quick start guide