COLBOR CL100 User manual

CL100 Video Light User Manual
Thank you for choosing COLBOR product. Please read this manual
carefully before use and follow all instructions mentioned herein.
Caring For Your COLBOR Product
Operation Instructions
Product Instructions
Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
The product is not waterproof.
Do not leave the product unattended while in use. Keep out of reach of
children.
Must remove the protective cover before use.
Do not handle with wet hands. Do not touch hot COB surface.
Please do not block the ventilation and do not look at the light directly when
it is on.
Do not attempt to disassemble or modify the product. Doing so voids
warranty.
Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
Disconnect from the power supply when it is not in use.
Malfunction may be caused by dropping, impact of external force.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
If there is no operation for 10 seconds, the current settings are
automatically saved and the selection mode is exited.
① Power Button
Short press to turn on/ o the light
② Mode Switch
Default Mode: CCT
Each press switches to next lighting mode
(CCT → EFF-CANDLE → EFF-BONFIRE → EFF-BLN → EFF-FAULTY BULB
→ EFF-FLASH → EFF-LIGHTNING)
Long press for 3 seconds to enter Overclock mode.
In overclock mode, the output power will be enhanced for 60s. At this time,
the fan runs at full speed with the fan status of "FULL". When the mode
ends, the previous fan status restores.
③ Adjustment Dial
1.Short press the dial to switch between Brightness and Color Temperature
Control
2.Roll the dial to adjust the value
Brightness (0-100%); Color Temperature (2700-6500K)
3.Press the dial again to switch to another control
④Group Option
Press the button to set group (Group A/B/C/D/E)
⑤ Fan Option
Default Status: SMART
SMART-The xture will adjust the fan speed according to working temperature.
Press the Fan Option and switch to QUIET status.
QUIET-The fan is o. In order to protect the light, the power will be reduced to
avoid overheating damage.
⑥ Fan Status
SMART / QUIET / FULL
⑦Power Status
Percentage icon means battery power is being used
Plug icon means AC power is being used
Brightness Control 0-100%(5% Stepping)
Color Temperature Control (2700~6500K)
EFF
CANDLE
BONFIRE
Specic color temperature range: 2700~3000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~4000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
CCT Mode
EFF Mode
1. Connect the xture with the power adapter, then plug it into an electricity
supply.
2. Press the Power Button to turn on the light.
Press to switch
⑧ Brightness
⑨Color Temperature
⑩Group
BLN (Pulsing)
FAULTY BULB
FLASH
LIGHTNING
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 5600~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature: 6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
EFF
Brightness Control / Color Temperature / Rate Control
Short press the Adjustment Dial to switch among color temperature control (
“CCT” ashes), rate control (“RATE” ashes) and brightness control, then roll
the dial to adjust.
Remote Control Instructions
① Switch
② Overclock Mode
③ Brightness +
④ Brightness -
⑤ Color Temperature -
⑥ Color Temperature +
⑦ Fade In/ Fade Out
⑧ CCT Mode
⑨ EFF Mode/ Remote Pairing
⑩ Rate (Flicker Frequency)
⑪ Preset Color Temperature: 3200K
⑫ Preset Color Temperature: 6500K

CL100 Video Light User Manual
Thank you for choosing COLBOR product. Please read this manual
carefully before use and follow all instructions mentioned herein.
Caring For Your COLBOR Product
Operation Instructions
Product Instructions
Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
The product is not waterproof.
Do not leave the product unattended while in use. Keep out of reach of
children.
Must remove the protective cover before use.
Do not handle with wet hands. Do not touch hot COB surface.
Please do not block the ventilation and do not look at the light directly when
it is on.
Do not attempt to disassemble or modify the product. Doing so voids
warranty.
Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
Disconnect from the power supply when it is not in use.
Malfunction may be caused by dropping, impact of external force.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
If there is no operation for 10 seconds, the current settings are
automatically saved and the selection mode is exited.
① Power Button
Short press to turn on/ o the light
② Mode Switch
Default Mode: CCT
Each press switches to next lighting mode
(CCT → EFF-CANDLE → EFF-BONFIRE → EFF-BLN → EFF-FAULTY BULB
→ EFF-FLASH → EFF-LIGHTNING)
Long press for 3 seconds to enter Overclock mode.
In overclock mode, the output power will be enhanced for 60s. At this time,
the fan runs at full speed with the fan status of "FULL". When the mode
ends, the previous fan status restores.
③ Adjustment Dial
1.Short press the dial to switch between Brightness and Color Temperature
Control
2.Roll the dial to adjust the value
Brightness (0-100%); Color Temperature (2700-6500K)
3.Press the dial again to switch to another control
④Group Option
Press the button to set group (Group A/B/C/D/E)
⑤ Fan Option
Default Status: SMART
SMART-The xture will adjust the fan speed according to working temperature.
Press the Fan Option and switch to QUIET status.
QUIET-The fan is o. In order to protect the light, the power will be reduced to
avoid overheating damage.
⑥ Fan Status
SMART / QUIET / FULL
⑦Power Status
Percentage icon means battery power is being used
Plug icon means AC power is being used
Brightness Control 0-100%(5% Stepping)
Color Temperature Control (2700~6500K)
EFF
CANDLE
BONFIRE
Specic color temperature range: 2700~3000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~4000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
CCT Mode
EFF Mode
1. Connect the xture with the power adapter, then plug it into an electricity
supply.
2. Press the Power Button to turn on the light.
Press to switch
⑧ Brightness
⑨Color Temperature
⑩Group
BLN (Pulsing)
FAULTY BULB
FLASH
LIGHTNING
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 5600~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature: 6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
EFF
Brightness Control / Color Temperature / Rate Control
Short press the Adjustment Dial to switch among color temperature control (
“CCT” ashes), rate control (“RATE” ashes) and brightness control, then roll
the dial to adjust.
Remote Control Instructions
① Switch
② Overclock Mode
③ Brightness +
④ Brightness -
⑤ Color Temperature -
⑥ Color Temperature +
⑦ Fade In/ Fade Out
⑧ CCT Mode
⑨ EFF Mode/ Remote Pairing
⑩ Rate (Flicker Frequency)
⑪ Preset Color Temperature: 3200K
⑫ Preset Color Temperature: 6500K

CL100 Video Light User Manual
Thank you for choosing COLBOR product. Please read this manual
carefully before use and follow all instructions mentioned herein.
Caring For Your COLBOR Product
Operation Instructions
Product Instructions
Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
The product is not waterproof.
Do not leave the product unattended while in use. Keep out of reach of
children.
Must remove the protective cover before use.
Do not handle with wet hands. Do not touch hot COB surface.
Please do not block the ventilation and do not look at the light directly when
it is on.
Do not attempt to disassemble or modify the product. Doing so voids
warranty.
Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
Disconnect from the power supply when it is not in use.
Malfunction may be caused by dropping, impact of external force.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
If there is no operation for 10 seconds, the current settings are
automatically saved and the selection mode is exited.
① Power Button
Short press to turn on/ o the light
② Mode Switch
Default Mode: CCT
Each press switches to next lighting mode
(CCT → EFF-CANDLE → EFF-BONFIRE → EFF-BLN → EFF-FAULTY BULB
→ EFF-FLASH → EFF-LIGHTNING)
Long press for 3 seconds to enter Overclock mode.
In overclock mode, the output power will be enhanced for 60s. At this time,
the fan runs at full speed with the fan status of "FULL". When the mode
ends, the previous fan status restores.
③ Adjustment Dial
1.Short press the dial to switch between Brightness and Color Temperature
Control
2.Roll the dial to adjust the value
Brightness (0-100%); Color Temperature (2700-6500K)
3.Press the dial again to switch to another control
④Group Option
Press the button to set group (Group A/B/C/D/E)
⑤ Fan Option
Default Status: SMART
SMART-The xture will adjust the fan speed according to working temperature.
Press the Fan Option and switch to QUIET status.
QUIET-The fan is o. In order to protect the light, the power will be reduced to
avoid overheating damage.
⑥ Fan Status
SMART / QUIET / FULL
⑦Power Status
Percentage icon means battery power is being used
Plug icon means AC power is being used
Brightness Control 0-100%(5% Stepping)
Color Temperature Control (2700~6500K)
EFF
CANDLE
BONFIRE
Specic color temperature range: 2700~3000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~4000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
CCT Mode
EFF Mode
1. Connect the xture with the power adapter, then plug it into an electricity
supply.
2. Press the Power Button to turn on the light.
Press to switch
⑧ Brightness
⑨Color Temperature
⑩Group
BLN (Pulsing)
FAULTY BULB
FLASH
LIGHTNING
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 5600~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature: 6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
EFF
Brightness Control / Color Temperature / Rate Control
Short press the Adjustment Dial to switch among color temperature control (
“CCT” ashes), rate control (“RATE” ashes) and brightness control, then roll
the dial to adjust.
Remote Control Instructions
① Switch
② Overclock Mode
③ Brightness +
④ Brightness -
⑤ Color Temperature -
⑥ Color Temperature +
⑦ Fade In/ Fade Out
⑧ CCT Mode
⑨ EFF Mode/ Remote Pairing
⑩ Rate (Flicker Frequency)
⑪ Preset Color Temperature: 3200K
⑫ Preset Color Temperature: 6500K

CL100 Video Light User Manual
Thank you for choosing COLBOR product. Please read this manual
carefully before use and follow all instructions mentioned herein.
Caring For Your COLBOR Product
Operation Instructions
Product Instructions
Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
The product is not waterproof.
Do not leave the product unattended while in use. Keep out of reach of
children.
Must remove the protective cover before use.
Do not handle with wet hands. Do not touch hot COB surface.
Please do not block the ventilation and do not look at the light directly when
it is on.
Do not attempt to disassemble or modify the product. Doing so voids
warranty.
Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
Disconnect from the power supply when it is not in use.
Malfunction may be caused by dropping, impact of external force.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
If there is no operation for 10 seconds, the current settings are
automatically saved and the selection mode is exited.
① Power Button
Short press to turn on/ o the light
② Mode Switch
Default Mode: CCT
Each press switches to next lighting mode
(CCT → EFF-CANDLE → EFF-BONFIRE → EFF-BLN → EFF-FAULTY BULB
→ EFF-FLASH → EFF-LIGHTNING)
Long press for 3 seconds to enter Overclock mode.
In overclock mode, the output power will be enhanced for 60s. At this time,
the fan runs at full speed with the fan status of "FULL". When the mode
ends, the previous fan status restores.
③ Adjustment Dial
1.Short press the dial to switch between Brightness and Color Temperature
Control
2.Roll the dial to adjust the value
Brightness (0-100%); Color Temperature (2700-6500K)
3.Press the dial again to switch to another control
④Group Option
Press the button to set group (Group A/B/C/D/E)
⑤ Fan Option
Default Status: SMART
SMART-The xture will adjust the fan speed according to working temperature.
Press the Fan Option and switch to QUIET status.
QUIET-The fan is o. In order to protect the light, the power will be reduced to
avoid overheating damage.
⑥ Fan Status
SMART / QUIET / FULL
⑦Power Status
Percentage icon means battery power is being used
Plug icon means AC power is being used
Brightness Control 0-100%(5% Stepping)
Color Temperature Control (2700~6500K)
EFF
CANDLE
BONFIRE
Specic color temperature range: 2700~3000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~4000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
CCT Mode
EFF Mode
1. Connect the xture with the power adapter, then plug it into an electricity
supply.
2. Press the Power Button to turn on the light.
Press to switch
⑧ Brightness
⑨Color Temperature
⑩Group
BLN (Pulsing)
FAULTY BULB
FLASH
LIGHTNING
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 5600~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature: 6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
EFF
Brightness Control / Color Temperature / Rate Control
Short press the Adjustment Dial to switch among color temperature control (
“CCT” ashes), rate control (“RATE” ashes) and brightness control, then roll
the dial to adjust.
Remote Control Instructions
① Switch
② Overclock Mode
③ Brightness +
④ Brightness -
⑤ Color Temperature -
⑥ Color Temperature +
⑦ Fade In/ Fade Out
⑧ CCT Mode
⑨ EFF Mode/ Remote Pairing
⑩ Rate (Flicker Frequency)
⑪ Preset Color Temperature: 3200K
⑫ Preset Color Temperature: 6500K

CL100 Video Light User Manual
Thank you for choosing COLBOR product. Please read this manual
carefully before use and follow all instructions mentioned herein.
Caring For Your COLBOR Product
Operation Instructions
Product Instructions
Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
The product is not waterproof.
Do not leave the product unattended while in use. Keep out of reach of
children.
Must remove the protective cover before use.
Do not handle with wet hands. Do not touch hot COB surface.
Please do not block the ventilation and do not look at the light directly when
it is on.
Do not attempt to disassemble or modify the product. Doing so voids
warranty.
Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
Disconnect from the power supply when it is not in use.
Malfunction may be caused by dropping, impact of external force.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
If there is no operation for 10 seconds, the current settings are
automatically saved and the selection mode is exited.
① Power Button
Short press to turn on/ o the light
② Mode Switch
Default Mode: CCT
Each press switches to next lighting mode
(CCT → EFF-CANDLE → EFF-BONFIRE → EFF-BLN → EFF-FAULTY BULB
→ EFF-FLASH → EFF-LIGHTNING)
Long press for 3 seconds to enter Overclock mode.
In overclock mode, the output power will be enhanced for 60s. At this time,
the fan runs at full speed with the fan status of "FULL". When the mode
ends, the previous fan status restores.
③ Adjustment Dial
1.Short press the dial to switch between Brightness and Color Temperature
Control
2.Roll the dial to adjust the value
Brightness (0-100%); Color Temperature (2700-6500K)
3.Press the dial again to switch to another control
④Group Option
Press the button to set group (Group A/B/C/D/E)
⑤ Fan Option
Default Status: SMART
SMART-The xture will adjust the fan speed according to working temperature.
Press the Fan Option and switch to QUIET status.
QUIET-The fan is o. In order to protect the light, the power will be reduced to
avoid overheating damage.
⑥ Fan Status
SMART / QUIET / FULL
⑦Power Status
Percentage icon means battery power is being used
Plug icon means AC power is being used
Brightness Control 0-100%(5% Stepping)
Color Temperature Control (2700~6500K)
EFF
CANDLE
BONFIRE
Specic color temperature range: 2700~3000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~4000K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
CCT Mode
EFF Mode
1. Connect the xture with the power adapter, then plug it into an electricity
supply.
2. Press the Power Button to turn on the light.
Press to switch
⑧ Brightness
⑨Color Temperature
⑩Group
BLN (Pulsing)
FAULTY BULB
FLASH
LIGHTNING
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 2700~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature range: 5600~6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
Specic color temperature: 6500K
Specic brightness range: 30~100
Rate: 5 levels of icker frequency (05 ﹥ 04 ﹥
03 ﹥ 02 ﹥ 01)
EFF
Brightness Control / Color Temperature / Rate Control
Short press the Adjustment Dial to switch among color temperature control (
“CCT” ashes), rate control (“RATE” ashes) and brightness control, then roll
the dial to adjust.
Remote Control Instructions
① Switch
② Overclock Mode
③ Brightness +
④ Brightness -
⑤ Color Temperature -
⑥ Color Temperature +
⑦ Fade In/ Fade Out
⑧ CCT Mode
⑨ EFF Mode/ Remote Pairing
⑩ Rate (Flicker Frequency)
⑪ Preset Color Temperature: 3200K
⑫ Preset Color Temperature: 6500K

Pair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
EFF Mode button on the remote control in 3 seconds after the power supply is
connected.
3. If they are paired, the CL100 will ash three times and display the program
version number.
4. The remote control can be used as required once paired.
Unpair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
Overclock Mode button on the remote control in 3 seconds after the power
supply is connected.
3. If the pairing is cancelled successfully, the CL100 will ash three times.
In the case of multi-light control, all lights must be switched o before the
remote control is applied. Otherwise, the control will be out of sync.
Specications
Color Rendering Index: ≥ 97
Color Temperature Range: 2700-6500K
Beam Angle: ≈∠ 120° (With Standard Cover 55° )
Illumination: 2998Lux (at 3.28ft / 1m 6500K, None Cover); 10123Lux (at 3.28ft /
1m 6500K, With Standard Cover)
Power: 100W (Constant Power)
Light Working Voltage: DC 15-24V 6.32A
Connector: GX16 3-Pin Connector
Body Material: ABS
Light Dimension(mm): 202*116*117 (Light Base Not Included)
Light Weight: 1.1kg/39oz
Package List
CL100 Video Light x1 Bowens Mount
Cover x1
Protective Cover x1
Remote Control
x1 (Optional)
Packing Bag x1
Velcro x2Power Adapter x1
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
1. Customers are entitled to free replacement or repair service in case of
quality defect(s) found in the product under normal use within 30 days upon
receipt of the product.
2. Original COLBOR products are entitled to 12-month limited warranty service.
The warranty period begins on the date of purchase of brand new, unused
products by the rst end-user.
Within the warranty period, if product defect or failure is attributable to material
defection or technological problem, the defective product or defective part will
be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
1. Faults resulted from inappropriate use of a product without following its
operation specication
2. Articial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or
damp
3. Modications to a product by its user or a third party without prior written
WARRANTY CERTIFICATE
USER
INFORMATION
SALES
INFORMATION
REPAIR RECORD
RESULT
Please register your warranty. Meanwhile, you are welcomed to contact us via Email.
Customer Name:
Phone Number:
Email:
Address:
Service Date:
Technician:
Issue:
Sales Date:
Model:
Product Code:
Dealer:
Solved Unsolved Returned(Replaced)
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
[e-mail]
www.colborlight.com
Guangzhou Zhiying Technology Co., Ltd
consent of COLBOR, e.g. replacement of element or circuit, label alteration
4. The code on product is inconsistent with that of warranty certicate, or the
code on the product or warranty certicate is altered or torn o
5. All consumable accessory attached to a product, like cable, cover
6. Faults as a result of force majeure, such as re, ood, lightning, etc.
Warranty Claim Procedure
1. If failure or any problem occurs to your product after purchase, please
contact a local agent for assistance, or you can always contact COLBOR’s
customer service through email.
2. Please retain your sales receipt and warranty certicate as proof of
purchase. If any of these documents is missing, only sales return or chargeable
service will be provided.
3. If the COLBOR product is out of the warranty coverage, the service and the
parts cost will be charged.

Pair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
EFF Mode button on the remote control in 3 seconds after the power supply is
connected.
3. If they are paired, the CL100 will ash three times and display the program
version number.
4. The remote control can be used as required once paired.
Unpair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
Overclock Mode button on the remote control in 3 seconds after the power
supply is connected.
3. If the pairing is cancelled successfully, the CL100 will ash three times.
In the case of multi-light control, all lights must be switched o before the
remote control is applied. Otherwise, the control will be out of sync.
Specications
Color Rendering Index: ≥ 97
Color Temperature Range: 2700-6500K
Beam Angle: ≈∠ 120° (With Standard Cover 55° )
Illumination: 2998Lux (at 3.28ft / 1m 6500K, None Cover); 10123Lux (at 3.28ft /
1m 6500K, With Standard Cover)
Power: 100W (Constant Power)
Light Working Voltage: DC 15-24V 6.32A
Connector: GX16 3-Pin Connector
Body Material: ABS
Light Dimension(mm): 202*116*117 (Light Base Not Included)
Light Weight: 1.1kg/39oz
Package List
CL100 Video Light x1 Bowens Mount
Cover x1
Protective Cover x1
Remote Control
x1 (Optional)
Packing Bag x1
Velcro x2Power Adapter x1
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
1. Customers are entitled to free replacement or repair service in case of
quality defect(s) found in the product under normal use within 30 days upon
receipt of the product.
2. Original COLBOR products are entitled to 12-month limited warranty service.
The warranty period begins on the date of purchase of brand new, unused
products by the rst end-user.
Within the warranty period, if product defect or failure is attributable to material
defection or technological problem, the defective product or defective part will
be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
1. Faults resulted from inappropriate use of a product without following its
operation specication
2. Articial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or
damp
3. Modications to a product by its user or a third party without prior written
WARRANTY CERTIFICATE
USER
INFORMATION
SALES
INFORMATION
REPAIR RECORD
RESULT
Please register your warranty. Meanwhile, you are welcomed to contact us via Email.
Customer Name:
Phone Number:
Email:
Address:
Service Date:
Technician:
Issue:
Sales Date:
Model:
Product Code:
Dealer:
Solved Unsolved Returned(Replaced)
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
[e-mail]
www.colborlight.com
Guangzhou Zhiying Technology Co., Ltd
consent of COLBOR, e.g. replacement of element or circuit, label alteration
4. The code on product is inconsistent with that of warranty certicate, or the
code on the product or warranty certicate is altered or torn o
5. All consumable accessory attached to a product, like cable, cover
6. Faults as a result of force majeure, such as re, ood, lightning, etc.
Warranty Claim Procedure
1. If failure or any problem occurs to your product after purchase, please
contact a local agent for assistance, or you can always contact COLBOR’s
customer service through email.
2. Please retain your sales receipt and warranty certicate as proof of
purchase. If any of these documents is missing, only sales return or chargeable
service will be provided.
3. If the COLBOR product is out of the warranty coverage, the service and the
parts cost will be charged.

Pair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
EFF Mode button on the remote control in 3 seconds after the power supply is
connected.
3. If they are paired, the CL100 will ash three times and display the program
version number.
4. The remote control can be used as required once paired.
Unpair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
Overclock Mode button on the remote control in 3 seconds after the power
supply is connected.
3. If the pairing is cancelled successfully, the CL100 will ash three times.
In the case of multi-light control, all lights must be switched o before the
remote control is applied. Otherwise, the control will be out of sync.
Specications
Color Rendering Index: ≥ 97
Color Temperature Range: 2700-6500K
Beam Angle: ≈∠ 120° (With Standard Cover 55° )
Illumination: 2998Lux (at 3.28ft / 1m 6500K, None Cover); 10123Lux (at 3.28ft /
1m 6500K, With Standard Cover)
Power: 100W (Constant Power)
Light Working Voltage: DC 15-24V 6.32A
Connector: GX16 3-Pin Connector
Body Material: ABS
Light Dimension(mm): 202*116*117 (Light Base Not Included)
Light Weight: 1.1kg/39oz
Package List
CL100 Video Light x1 Bowens Mount
Cover x1
Protective Cover x1
Remote Control
x1 (Optional)
Packing Bag x1
Velcro x2Power Adapter x1
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
1. Customers are entitled to free replacement or repair service in case of
quality defect(s) found in the product under normal use within 30 days upon
receipt of the product.
2. Original COLBOR products are entitled to 12-month limited warranty service.
The warranty period begins on the date of purchase of brand new, unused
products by the rst end-user.
Within the warranty period, if product defect or failure is attributable to material
defection or technological problem, the defective product or defective part will
be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
1. Faults resulted from inappropriate use of a product without following its
operation specication
2. Articial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or
damp
3. Modications to a product by its user or a third party without prior written
WARRANTY CERTIFICATE
USER
INFORMATION
SALES
INFORMATION
REPAIR RECORD
RESULT
Please register your warranty. Meanwhile, you are welcomed to contact us via Email.
Customer Name:
Phone Number:
Email:
Address:
Service Date:
Technician:
Issue:
Sales Date:
Model:
Product Code:
Dealer:
Solved Unsolved Returned(Replaced)
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
[e-mail]
www.colborlight.com
Guangzhou Zhiying Technology Co., Ltd
consent of COLBOR, e.g. replacement of element or circuit, label alteration
4. The code on product is inconsistent with that of warranty certicate, or the
code on the product or warranty certicate is altered or torn o
5. All consumable accessory attached to a product, like cable, cover
6. Faults as a result of force majeure, such as re, ood, lightning, etc.
Warranty Claim Procedure
1. If failure or any problem occurs to your product after purchase, please
contact a local agent for assistance, or you can always contact COLBOR’s
customer service through email.
2. Please retain your sales receipt and warranty certicate as proof of
purchase. If any of these documents is missing, only sales return or chargeable
service will be provided.
3. If the COLBOR product is out of the warranty coverage, the service and the
parts cost will be charged.

Pair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
EFF Mode button on the remote control in 3 seconds after the power supply is
connected.
3. If they are paired, the CL100 will ash three times and display the program
version number.
4. The remote control can be used as required once paired.
Unpair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
Overclock Mode button on the remote control in 3 seconds after the power
supply is connected.
3. If the pairing is cancelled successfully, the CL100 will ash three times.
In the case of multi-light control, all lights must be switched o before the
remote control is applied. Otherwise, the control will be out of sync.
Specications
Color Rendering Index: ≥ 97
Color Temperature Range: 2700-6500K
Beam Angle: ≈∠ 120° (With Standard Cover 55° )
Illumination: 2998Lux (at 3.28ft / 1m 6500K, None Cover); 10123Lux (at 3.28ft /
1m 6500K, With Standard Cover)
Power: 100W (Constant Power)
Light Working Voltage: DC 15-24V 6.32A
Connector: GX16 3-Pin Connector
Body Material: ABS
Light Dimension(mm): 202*116*117 (Light Base Not Included)
Light Weight: 1.1kg/39oz
Package List
CL100 Video Light x1 Bowens Mount
Cover x1
Protective Cover x1
Remote Control
x1 (Optional)
Packing Bag x1
Velcro x2Power Adapter x1
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
1. Customers are entitled to free replacement or repair service in case of
quality defect(s) found in the product under normal use within 30 days upon
receipt of the product.
2. Original COLBOR products are entitled to 12-month limited warranty service.
The warranty period begins on the date of purchase of brand new, unused
products by the rst end-user.
Within the warranty period, if product defect or failure is attributable to material
defection or technological problem, the defective product or defective part will
be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
1. Faults resulted from inappropriate use of a product without following its
operation specication
2. Articial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or
damp
3. Modications to a product by its user or a third party without prior written
WARRANTY CERTIFICATE
USER
INFORMATION
SALES
INFORMATION
REPAIR RECORD
RESULT
Please register your warranty. Meanwhile, you are welcomed to contact us via Email.
Customer Name:
Phone Number:
Email:
Address:
Service Date:
Technician:
Issue:
Sales Date:
Model:
Product Code:
Dealer:
Solved Unsolved Returned(Replaced)
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
[e-mail]
www.colborlight.com
Guangzhou Zhiying Technology Co., Ltd
consent of COLBOR, e.g. replacement of element or circuit, label alteration
4. The code on product is inconsistent with that of warranty certicate, or the
code on the product or warranty certicate is altered or torn o
5. All consumable accessory attached to a product, like cable, cover
6. Faults as a result of force majeure, such as re, ood, lightning, etc.
Warranty Claim Procedure
1. If failure or any problem occurs to your product after purchase, please
contact a local agent for assistance, or you can always contact COLBOR’s
customer service through email.
2. Please retain your sales receipt and warranty certicate as proof of
purchase. If any of these documents is missing, only sales return or chargeable
service will be provided.
3. If the COLBOR product is out of the warranty coverage, the service and the
parts cost will be charged.
Pair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
EFF Mode button on the remote control in 3 seconds after the power supply is
connected.
3. If they are paired, the CL100 will ash three times and display the program
version number.
4. The remote control can be used as required once paired.
Unpair the CL100 with the remote control
1. Disconnect the CL100 from the power supply and reconnect with the
electricity.
2. Point the remote control to the CL100 control panel and long press the
Overclock Mode button on the remote control in 3 seconds after the power
supply is connected.
3. If the pairing is cancelled successfully, the CL100 will ash three times.
In the case of multi-light control, all lights must be switched o before the
remote control is applied. Otherwise, the control will be out of sync.
Specications
Color Rendering Index: ≥ 97
Color Temperature Range: 2700-6500K
Beam Angle: ≈∠ 120° (With Standard Cover 55° )
Illumination: 2998Lux (at 3.28ft / 1m 6500K, None Cover); 10123Lux (at 3.28ft /
1m 6500K, With Standard Cover)
Power: 100W (Constant Power)
Light Working Voltage: DC 15-24V 6.32A
Connector: GX16 3-Pin Connector
Body Material: ABS
Light Dimension(mm): 202*116*117 (Light Base Not Included)
Light Weight: 1.1kg/39oz
Package List
CL100 Video Light x1 Bowens Mount
Cover x1
Protective Cover x1
Remote Control
x1 (Optional)
Packing Bag x1
Velcro x2Power Adapter x1
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
1. Customers are entitled to free replacement or repair service in case of
quality defect(s) found in the product under normal use within 30 days upon
receipt of the product.
2. Original COLBOR products are entitled to 12-month limited warranty service.
The warranty period begins on the date of purchase of brand new, unused
products by the rst end-user.
Within the warranty period, if product defect or failure is attributable to material
defection or technological problem, the defective product or defective part will
be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
1. Faults resulted from inappropriate use of a product without following its
operation specication
2. Articial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or
damp
3. Modications to a product by its user or a third party without prior written
WARRANTY CERTIFICATE
USER
INFORMATION
SALES
INFORMATION
REPAIR RECORD
RESULT
Please register your warranty. Meanwhile, you are welcomed to contact us via Email.
Customer Name:
Phone Number:
Email:
Address:
Service Date:
Technician:
Issue:
Sales Date:
Model:
Product Code:
Dealer:
Solved Unsolved Returned(Replaced)
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
[email protected]
www.colborlight.com
Guangzhou Zhiying Technology Co., Ltd
consent of COLBOR, e.g. replacement of element or circuit, label alteration
4. The code on product is inconsistent with that of warranty certicate, or the
code on the product or warranty certicate is altered or torn o
5. All consumable accessory attached to a product, like cable, cover
6. Faults as a result of force majeure, such as re, ood, lightning, etc.
Warranty Claim Procedure
1. If failure or any problem occurs to your product after purchase, please
contact a local agent for assistance, or you can always contact COLBOR’s
customer service through email.
2. Please retain your sales receipt and warranty certicate as proof of
purchase. If any of these documents is missing, only sales return or chargeable
service will be provided.
3. If the COLBOR product is out of the warranty coverage, the service and the
parts cost will be charged.