Flare Fireplaces Front Series User manual

Modern Gas Fireplaces
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATION AND SERVICE OF THIS APPLIANCE MUST BE
PERFORMED BY QUALIFIED CERTIFIED NFI PERSONNEL OR
CERTIFIED FLARE FIREPLACE DEALER.
Massachusetts: The piping and final gas connection must be performed by a
licensed plumber or gas fitter in the State of Massachusetts. Also, see
Carbon Monoxide detector requirements on page 56
NOTICE
Flare Fireplaces Installation Guide –Large Units
[Flare Double Corner, Left Corner, Right Corner] v11.1
FLARE REQUIRES INSTALLATION BE
PERFORMED BY AN NFI CERTIFIED INSTALLER,
OR A CERTIFIED FLAREAUTHORIZED
INSTALLER. INSTALLATIONS THAT DO NOT
FOLLOW THIS INSTRUCTION WILL NOT BE
COVERED BY WARRANTY OR SERVICED.

2 | P a g e
TABLE OF CONTENTS
SAFETY INFO AND WARNINGS ......................................................................................................................................................4
FLARE FIREPLACES –FRAMELESS IN EVERY WAY ..........................................................................................................................7
SAFETY...........................................................................................................................................................................................7
CSA CERTIFICATION........................................................................................................................................................................7
MANUAL MODEL LIST & INFORMATION .......................................................................................................................................8
FIREPLACE OPERATION .................................................................................................................................................................9
ON/OFF OPERATION............................................................................................................................................................................9
WALL SWITCH –OPTIONAL....................................................................................................................................................................9
MEDIA ARRANGEMENTS .....................................................................................................................................................................10
MEDIA CALCULATIONS.......................................................................................................................................................................11
EXTERNAL GLASS REMOVAL –DOUBLE GLASS FIREPLACE .............................................................................................................................12
SIDE GLASS TRIM REMOVAL /INSTALLATION –FLARE H24” ....................................................................................................................13
INTERNAL GLASS REMOVAL..................................................................................................................................................................14
REFLECTIVE BACK INSTALL ..................................................................................................................................................................16
INSTALLATION STEPS ..................................................................................................................................................................17
INSTALLATION PREPARATION.....................................................................................................................................................18
ACCESS PANEL.................................................................................................................................................................................18
FIREPLACE UNPACKING.......................................................................................................................................................................19
FIREPLACE ASSEMBLY..................................................................................................................................................................20
LED LIGHTS..................................................................................................................................................................................26
LED LIGHT INSTALL AND POWER............................................................................................................................................................27
LED CONTROLLER AND REMOTE............................................................................................................................................................28
VENT TERMINATION ...................................................................................................................................................................30
VENT AND FIREPLACE SIZE ...................................................................................................................................................................31
MINIMUM COMBUSTIBLE CLEARANCES FROM VENT ...................................................................................................................................31
VERTICAL TERMINATION..............................................................................................................................................................32
VENT TERMINATION CLEARANCES..............................................................................................................................................34
VENT RESTRICTOR SETUP.....................................................................................................................................................................36
CHIMNEY PATH INSTALLATION AND PLANNING.........................................................................................................................37
VENT PATH DETERMINATION ...............................................................................................................................................................38
FLARE 60/60H/60EH ....................................................................................................................................................................39
FLARE 70/70H/70EH ....................................................................................................................................................................40
FLARE 80/80H/80EH ....................................................................................................................................................................41
FLARE 100/100H/100EH...............................................................................................................................................................42
POWER VENTING ........................................................................................................................................................................43
ELECTRICAL CONNECTION TO THE PV SYSTEM..........................................................................................................................................45

3 | P a g e
GAS INSTALLATION .....................................................................................................................................................................46
GENERAL ........................................................................................................................................................................................46
ORIFICE SIZE ....................................................................................................................................................................................47
GAS VALVE ACCESS DOOR....................................................................................................................................................................48
MANUAL GAS SHUT OFF .....................................................................................................................................................................48
LIQUID PROPANE USAGE IN AFLARE FIREPLACE ...........................................................................................................................48
COMMONWEALTH OF MASSACHUSETTS..................................................................................................................................................49
FLARE FIREPLACES - DOUBLE GLASS............................................................................................................................................50
OVERVIEW ......................................................................................................................................................................................50
DOUBLE GLASS -INSTRUCTIONS............................................................................................................................................................51
ELECTRICAL REQUIREMENT- POWER REQUIREMENT..................................................................................................................53
TELEVISION MOUNTING ABOVE FIREPLACE................................................................................................................................53
TV INSTALL –FLAT EXAMPLE ................................................................................................................................................................54
TV INSTALL –L TYPE EXAMPLE ..............................................................................................................................................................55
TV INSTALL RECESS –45 DEGREE ELBOW ON TOP OF THE UNIT .....................................................................................................................56
TV INSTALL WITHOUT RECESS –MANTEL INSTALLATION ..............................................................................................................................57
TV INSTALLED FLUSH ABOVE FIREPLACE...................................................................................................................................................58
CLEARANCES ...............................................................................................................................................................................59
GENERAL INFORMATION AND STEPS.......................................................................................................................................................59
COMBUSTIBLE FINISHING MATERIAL CLEARANCES.......................................................................................................................65
CLEARANCES SPECIFICATION ................................................................................................................................................................66
MANTEL CLEARANCE..........................................................................................................................................................................67
CLEARANCE TO SPRINKLER...........................................................................................................................................................68
HEAT RELEASES.................................................................................................................................................................................69
AIR INTAKE......................................................................................................................................................................................70
EXAMPLES OF HEAT RELEASES ..............................................................................................................................................................71
FLARE FRONT,SEE THROUGH,AND CORNER FIREPLACE CLEARANCE ...............................................................................................................72
Flat –side and isometric view ......................................................................................................................................................72
L shape –side and isometric view ................................................................................................................................................74
HOME AUTOMATION..................................................................................................................................................................76
ELECTRIC AND CONTROL.............................................................................................................................................................77
ELECTRIC DIAGRAM -SCREEN.............................................................................................................................................................77
ELECTRIC DIAGRAM –DOUBLE GLASS OR PV..........................................................................................................................................78
DOUBLE GLASS BOARD &LED LIGHT GUIDE ..........................................................................................................................................79
ELECTRIC DIAGRAM –PV SYSTEM..........................................................................................................................................................80
REPLACEMENT PARTS .................................................................................................................................................................81
MAINTENANCE............................................................................................................................................................................82
APPENDIX....................................................................................................................................................................................84
MAINTENANCE LOG...........................................................................................................................................................................84
WARRANTY POLICY............................................................................................................................................................................85

4 | P a g e
SAFETY INFO AND WARNINGS
WARNING!
If the information in these instructions are not followed exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
Installation and services must be performed by a qualified installer, service agency or the supplier.
WARNING!
The direct vent system appliance must be installed as an OEM installation in manufactured homes (USA only)
or an aftermarket permanently located, or a mobile home, where no prohibited by local codes and must be
installed in accordance with Manufacturer’s instructions and the Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280, in the United States, or the Standard for Installation in Mobile Homes, CAN/
CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is supplied
with the appliance.
This product is listed to the ANSI standards for ANSI A21.50b-2009 / CSA 2.22b-2009 Vented Gas
Fireplaces CAN/ CGA 2.17-M91 Gas-Fired Appliance for use at high altitudes.
WARNING!
NEVER LEAVE CHILDREN OR ANY OTHER AT-RISK INDIVIDUAL ALONE WITH THE
APPLIANCE.
This Product is Listed to Ansi standard Z21.88/CSA 2.33-2016 Vented Gas Fireplaces Can/CGA 2.17-M91
Gas Fired Appliance For Use At High Altitude. Please check High Altitude related istructions

5 | P a g e
WARNING!
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or
clothing ignition.
WARNING!
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children
and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at-risk
individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young
children and other at-risk individuals out of the room and away from hot surfaces.
WARNING!
This appliance must be electrically wired and grounded in accordance with local codes, or in the absence of local codes, with
National Electric Code ANSI/NFPA 70 –latest edition or the Canadian Electric Code CSA C22.1
A 110-120V AC Circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with
the applicable electrical codes, when it is installed in locations such as bathrooms or near sinks.
Proposition 65 Warning: Fuels used in gas, wood burning or oil fired appliances, and the products of combustion of such
fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6. In the State of Massachusetts, only a licensed plumber and gas fitter may
install this product. See Note for the Commonwealth of Massachusetts.
State of California. Proposition 65 Warning. Fuels used in gas, wood-burning or oil-fired appliances, and the products
of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other
reproductive harm. California Health & Safety Code Sec. 25249.6

6 | P a g e
Do not operate this appliance with the glass removed, cracked or broken. Only glass doors certified
with this appliance shall be used.
If the barrier supplied with this appliance becomes damaged, the barrier shall be replaced with the
manufacturer's barrier for this appliance.
Any Barrier Screen or guard removed for servicing must be replaced before operating fireplace.
These units must use one of the vent systems described in the Flue Venting section of this manual.
This gas fireplace and vent system must be vented directly to the outside and must never be
attached to a chimney serving a separate solid fuel-burning fireplace. Each gas fireplace must use a
separate vent system. Common vent systems are prohibited.
The vent system for this fireplace must be periodically examined by a qualified service agency to
maintain venting performance and safety. If the vent-air intake system is disassembled for any
reason, contact your fireplace installer and reinstall per the vent instructions provided for the initial
installation.
Inspect the external vent cap on regular basis (monthly) to make sure that no debris is interfering
with the airflow. The flow of combustion and ventilation air are not to be obstructed.
Turn off the gas before servicing this fireplace. It is recommended that a qualified service
technician perform a fireplace check-up at the beginning of each heating season.
This vented gas fireplace heater is not for use with air filters.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Refer to the owner’s information manual provided with this fireplace. For
assistance or additional information consult a qualified installer, service agency or the gas supplier.
WARNING!

7 | P a g e
FLARE FIREPLACES –FRAMELESS IN EVERY WAY
Flare Fireplaces is where innovation, quality and luxury come together to form new ideas. By combining
superior raw materials, contemporary design, creative technology and a frameless way of thinking, we have
created a full line of direct-vent fireplaces that are luxurious, simple to operate, and efficient. Our
Fireplaces are distinguished by their clean design, superior build quality and unique features.
SAFETY
CSA CERTIFICATION
All our fireplaces are tested and have been certified to meet stringent CSA guidelines, ensuring optimum
quality, safety and efficiency.
All our fireplaces have been certified and tested to work with Natural Gas or Propane.
Certification Information:
ANSI Z21.88/CSA 2.33-2016- Vented Gas Fireplace Heaters
CSA CLASSES:
CLASS 2901 84 / CLASS 2901 04
All fireplaces are rated for commercial and residential use.
The CSA Mark
The Canadian Standards Association (CSA) is a nonprofit association serving business, industry, government
and consumers in Canada and the global marketplace. Among many other activities, CSA develops
standards that enhance public safety.
A Nationally Recognized Testing Laboratory, CSA is very familiar with U.S. requirements. According to
OSHA regulations, the CSA-US Mark qualifies as an alternative to the UL Mark.
Here are some areas where CSA standards are applied:
•Canadian Electrical Code, Part III-Outside Wiring
•Electrical Engineering Standards
•Electromagnetic Compatibility

8 | P a g e
MANUAL MODEL LIST & INFORMATION
The Following manual should be used for the following Flare Fireplaces Models:
•Flare Front 120,140,160,180-400 “–16” (R), 24” (H), 30” (EH)
•Flare See-Through 120,140,160,180-400”– 16” (R), 24” (H), 30” (EH)
•Flare Corner Right & Left 120,140,160,180-400”–16” (R), 24” (H)
•Flare Double Corner 120,140,160,180-400”–16” (R), 24” (H)
•Flare Room Definer 120,140,160,180-400”–16” (R), 24” (H), 30” (EH)
All Flare Fireplaces large models share the same gas valve system, gas connection, and glass type, simplifying
installation and operation.
Flare Fireplaces vent run calculation should be checked and planned based on the relevant fireplace size.
All warnings and instructions apply to all models.
Refer to the model name for specific model, clearance and installation information.
Flare Fireplaces should only be connected to M&G DuraVent 5x8 venting system or 3x5 ( in case of a PV system ).
Refer to the specific appliance model and size to determine vent size (Gas specification table) and chimney pathway
requirements (Chimney path installation & planning table). For detailed chimney installation information please use
the M&G DuraVent direct vent installation manual: http://www.duravent.com
For details on ICC direct vent installation, please use the ICC installation guide.
http://icc-chimney.com/en/exceldirect-support
This product is listed to ANSI standards for “Vented Gas Fireplace Heaters” and applicable sections of “Gas Burning
Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High
Altitudes”.
Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and
permits.
This installation must conform to local codes. In the absence of local codes, you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified service technician, service agency or your dealer.
FLARE REQUIRES INSTALLATION BE
PERFORMED BY AN NFI CERTIFIED INSTALLER,
OR A CERTIFIED FLARE DEALER.
INSTALLATIONS THAT DO NOT FOLLOW THIS
INSTRUCTION WILL NOT BE COVERED BY
WARRANTY OR SERVICED.

9 | P a g e
FIREPLACE OPERATION
ON/OFF OPERATION
The Flare Fireplaces Honeywell ignition system is provided with a 110V plug that can be connected to a controlled outlet for
ON/OFF operation of the fireplace. The electrical plug can also be removed in order to connect directly for hardwire operation.
The ON Off operation of the Flare Fireplaces with a Honeywell valve is controlled by switching ON or Off power supply to the
fireplace plug or hardwire.
The Fireplace will attempt to start whenever electric power is supplied to it. The Fireplace power supply needs to be wired by
QUALIFIED ELECTRICIAN.
The electrician can provide the operator a switch to control the outlet the fireplace is connected to.
The use of the plug should only be done when access to the outlet is available even after installation is completed.
This appliance must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Manual Gas Shutoff –All Flare Fireplaces must be installed with an accessible manual Gas shutoff (Not included) . Please use you
local building code for details on the manual gas shutoff requirements.
WALL SWITCH –OPTIONAL
The Fireplace ON/OFF operation can be done with a standard wallswitch provided. The wallswitch connection to the
fireplace must be wired by a qualified electrician. The switch will be set to control the supply of 110V to the fireplace
outlet or hardwire input.

10 | P a g e
MEDIA ARRANGEMENTS
Flare Fireplaces can be equipped with different media types. Follow the instructions below for information on how to
add and arrange media in your Fireplace:
•Do not place any type of media on the pilot or in front of the pilot. Keep 1”distance from the pilot to allow
correct operation of the pilot.
•Media can be put over the Flare burner. Avoid placing media over the main burner ports as it may disrupt
flame in case of a clogged port. Avoid placing driftwood arching over burner, instead place in front or behind.
•If using media that was not supplied by Flare Fireplace, make sure that the media is certified/suitable to be
used in direct vent gas fireplaces.
•Keep the pilot front cover view open to be able to view the pilot spark and flame from outside.
•Fireglass:
a. ¼” or ½” Fire Glass may be used.
b. When the fireplace viewing window is open, and media is placed, make sure Fire Glass does not fall
on the ceramic glass lower frame as that may cause breakage when putting back the ceramic glass.
c. Make sure pilot is clear of any Fire Glass particles.
d. Flare Fire Glass can be put safely in to the firebox. Avoid overloading the burner with Fire Glass,
specifically over the main burner ports.
•Maintain minimum distance of ¼” from media to the fireplace glass panels.
•Use the manual for instructions on how to remove, replace, & arrange the fireplace glass media
PROPER DRIFTWOOD PLACEMENT IMPROPER DRIFTWOOD PLACEMENT
Ceramic Pebbles Fireglass
CHOKING HAZARD! Ensure that the fireplace area is clear of fire glass particles as these could be ingested by small
children. Vacuum area after installation.

11 | P a g e
MEDIA CALCULATIONS
Please follow the below described quantities of media placement in your firebox. Please note, over saturation of
media throughout the firebox may result in improper combustion or Soot within the fireplace or termination cap.
Use the Flare Fireplaces table for sizes to caculate the required media based on your fireplace size. For example:
Flare-FF-200 –Media caculation will be done based on the fact that the Flare Front 200 is assabled from 2 x Flare
Front 100.
30 6 Lbs 10 Lbs 2 Boxes 5 Pcs 9 Bags 4 Small 3 Large 1 Bag
45 11 Lbs 13 Lbs 3 Boxes 7 Pcs 12 Bags 6 Small 3 Large 1.5 Bags
50 12 Lbs 18 Lbs 4 Boxes 9 Pcs 15 Bags 7 Small 5 Large 2 Bags
60 15 Lbs 20 Lbs 5 Boxes 11 Pcs 17 Bags 9 Small 6 Large 2.5 Bags
70 17 Lbs 22 Lbs 5 Boxes 12 Pcs 18 Bags 10 Small 6 Large 3 Bags
80 21 Lbs 26 Lbs 6 Boxes 14 Pcs 22 Bags 11 Smal 7 Large 3.5 Bags
100 25 Lbs 30 Lbs 7 Boxes 17 Pcs 26 Bags 12 Small 8 Large 4.5 Bags
Glass
Diamond/
Rain Drops
Ceramic
Pebbles
Wood
Earth
Pebbles
Branches
Flare Front
Size
Embers
30 7 Lbs 10 Lbs 2 Boxes 5 Pcs 9 Bags 4 Small 3 Large 1 Bag
45 10 Lbs 13 Lbs 3 Boxes 7 Pcs 12 Bags 6 Small 3 Large 1.5 Bags
50 11 Lbs 18 Lbs 4 Boxes 9 Pcs 15 Bags 7 Small 5 Large 2 Bags
60 14 Lbs 20 Lbs 5 Boxes 11 Pcs 17 Bags 9 Small 6 Large 2.5 Bags
70 16 Lbs 22 Lbs 5 Boxes 12 Pcs 18 Bags 10 Small 6 Large 3 Bags
80 19 Lbs 26 Lbs 6 Boxes 14 Pcs 22 Bags 11 Smal 7 Large 3.5 Bags
100 23 Lbs 30 Lbs 7 Boxes 17 Pcs 26 Bags 12 Small 8 Large 4.5 Bags
Branches
Embers
Size
Glass
Diamond/
Rain Drops
Ceramic
Pebbles
Wood
Earth
Pebbles
Flare Corner

12 | P a g e
EXTERNAL GLASS REMOVAL –DOUBLE GLASS FIREPLACE
Follow the procedure below to remove and install back the fireplace external glass (double glass fireplace configuration).
Note: Suction cups are needed to remove the glass.
Warning! Turn off the fireplace and allow time for the unit to cool before proceeding.
Caution: The glass is very fragile and should be handled with care.
Warning! Double glass fireplace should NOT be operated without the external glass
•Confirm lock screws have been removed during install (should be done once, during install only).
•Attach glass suction cups to the glass. Use more than one suction cup if needed (any unit above 45”).
•Using suction cups, slightly push in the external glass top edge.
•Once glass has been pushed, slightly lift the glass to clear bottom part of the glass.
•Remove the glass and place in a secure location.
Install back external glass
•Attach glass suction cups to the glass. Use more than one suction cup if needed (any unit above 45”)
•Place upper edge of the glass in position and push latching trim.
•Once trim has been pushed in, slide glass top in position.
•Tilt in bottom edge of the glass in position as you are lifting the glass up.
•Glass is now secure in place. No bolts are needed to lock the glass.

13 | P a g e
SIDE GLASS TRIM REMOVAL / INSTALLATION –FLARE H 24”
The additional side trim piece for the H & EH models is installed differently than the standard height unit’s side trim pieces & has
additional steps required to remove & apply it successfully.
All work should be done with a cold fireplace, fireplace appliance turned off and manual gas valve shutoff. Unplug the fireplace
from any electric power (Double Glass Units)
The below picture shows the right-side glass trim
Step 1: Using a drill, untighten the screw that is located at the right
top of the trim side as shown in picture below
Step 2: Move the right trim glass to the left as shown
in picture below
Step 3: Remove the lower side of the trim slowly as
shown in picture below

14 | P a g e
INTERNAL GLASS REMOVAL
Follow the procedures below to remove and install the internal ceramic glass (double glass fireplace configuration).
Note: Suction cups are needed to remove the glass.
Warning! Turn off the fireplace and allow time for the unit to cool before attempting to remove the glass.
CAUTION:The ceramic glass is very fragile and should be handled with care.
CAUTION: Do not operate the appliance with glass removed, cracked or broken. Replacement of the panel(s) should
be done by a licensed or qualified service person
Step 1 –Attach glass suction cups to the glass. Remove the glass’lower magnetic trim. Place the trim in a secure
place. Any unit above 45” requires 2 suction cups to hold the glass.
Step 2 –Release the lower glass trim. The lower trim bolts can be released by hand and should not require any tools.
Once bolts are released remove lower glass holder trim.
Step 3 –Hold the glass suction cups and hand release trim bolt on the top. The trim does not need to be removed and
will only open to allow a gap for glass removal.
Step 4 –Push the glass up and clear it from the bottom as shown
When putting the glass back, DO NOT overtighten the bolts or glass may break
Step 1 Step 2

15 | P a g e
Step 3 Step 4-1
Step 4-2
When putting back the glass, DO NOT overtighten the bolts or glass may break
•Use step 4 –1 for putting the glass back.
•Glass trim screws should be closed hand-tight. DO NOT overtighten the bolts or glass may break.

16 | P a g e
REFLECTIVE BACK INSTALL
The Flare Fireplace large linear fireplaces include a reflective ceramic glass backing. The ceramic glass is tinted black to
create a reflection when the fireplace is running. The ceramic glass will enhance and protect the fireplace look and is
very easy to clean.
The reflective back is shipped outside the unit, inside a sleeve with the other glass panes. It should be mounted at the
back of the fireplace, placed in the gap between the fire bed (shown yellow below) and held by the top mounting
brackets (red circle).
Carefully carry the reflective back using suction cups, and place at a 45-degree angle as shown below.
Screw the mirror clamp as shown below, make sure you do not over-tighten the screw, & leave 1” of the screw
length out.

17 | P a g e
INSTALLATION STEPS
1. Prior to starting the installation, make sure you read and understand all WARNING information in the
manual. Do not start the installation if you are unclear about any of the installation related subjects.
2. Determine the following:
•The vent system configuration to be used based on the fireplace location. Follow the manual venting
section (Chimney path installation & planning tables) to determine the venting requirements and
setting.
Note: Venting requirements are model specific.
Note: Make sure the vent requirements are supported by the Flare manual and installation
instruction.
•Clearance requirements from combustible and non-combustible materials. Follow the clearance
instruction and example in the manual.
Note: Clearance instructions and examples are model specific.
•Gas supply piping. Confirm gas supply pipe size requirement based on your large fireplace BTU.
•Confirm if the fireplace is going to operate using Natural Gas (NG) or Propane. Use the attached
product label to confirm the fireplace is set for the expected gas type.
•Electrical wiring requirements.
•Framing and finishing details. Confirm is all metal framing or covered wood framing will be used.
3. Unpack the fireplace box,. Follow instruction for fireplace unpacking.
4. Put the Fireplace in the desired location. Verify clearance to non-combustible and combustible materials.
Follow the clearance instruction and example in the manual.
5. For LED units, connect LED system and test LED.
6. Attach the units back bracket to the wall framing.
7. For double glass units only: remove glass locking screws and discard.
8. Adjust Fireplace vent restrictor based on vent configuration and planning guide. Document vent restrictor
setup here: ___________________________.
9. Connect vent system to the Fireplace.
10. Connect gas (Gas connection section) line to the Fireplace and verify gas inlet and outlet pressure. Measure
and document gas pressure here: Inlet _______ W.C.
11. Confirm if adjustments for high altitude are needed (Installation at above 2000 Ft from sea level).
12. Connect electrical wiring for applicable units.
13. Insert and place Fireplace media. Use media arrangement guide from the manual.
14. Verification of:
•Ignition and pilot system.
•Burning and flame.
15. Complete framing and wall cover.
Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure
maximum safety and benefit.
Follow the Steps above to insure proper installation of the Gas appliance.
WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or
substitute components.

18 | P a g e
INSTALLATION PREPARATION
ACCESS PANEL
Flare recommends you build an access panel somewhere near the fireplace. This will provide easy access to all the
necessary parts that may need servicing, over time. While Flare also offers access to these components by going inside
the fireplace, with instructions HERE, you will find having a dedicated area where all your components can be easily
accessed for servicing, without the need to remove the glass, media, & burner is the preferred method.
HIDDEN ACCESS PANEL EXAMPLE

19 | P a g e
FIREPLACE UNPACKING
Follow the instructions below for unpacking the unit:
•Check the packing and confirm there is no external damage. If damage exists, please notify Flare Fireplaces
immediately.
•Remove the top wood studs and pull the external carton box up.
•Please do not remove the blue wrap completely at this stage.
•Leave the fireplace placed on the pallet for the next step: Fireplace legs setup.

20 | P a g e
FIREPLACE ASSEMBLY
Step 1: Unpack the accessories ( Power adapter & wall switch). The gas valve, receiver, control module must remain
wrapped until first fire up of unit.
Do Not Connect any screw that is not mentioned in this guide even if
there is a hole for it.
The Fireplace ability to contract and move during fire up and cool down depends on proper
assembly
Step 2: Preparation for Assembly
•Assemble units on a perfectly leveled area only.
•Assemble Flare Fireplaces large units in the final installation location, on the pre made
platform. It is not possible to move the assembled fireplace once units are connected.
•Fireplace platform under the fireplace should be covered with noncombustible material
(cement board or type X drywall. Large Flare Fireplaces do not have telescopic legs and
depend on the platform to adjust height.
•Make sure the fireplace chase is framed with metal studs or covered (With
noncombustible) prior to the assembly and positioning of the fireplace. Make sure there
are no exposed combustible materials in the fireplace chase. See clearances section for
more details.
Step 3: unpack Left-Side Box leave the Fireplace placed on the pallet in order to help you to connect
them together as shown in the picture bellow: