Flare Fireplaces Flare See-Through 30-100" User manual

Modern Gas Fireplaces - Linear Fireplaces
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATION AND SERVICE OF THIS APPLIANCE MUST BE
PERFORMED BY QUALIFIED CERTIFIED NFI PERSONNEL OR
CERTIFIED FLARE FIREPLACE DEALER.
Massachusetts: The piping and final gas connection must be performed by a
licensed plumber or gas fitter in the State of Massachusetts. Also, see
Carbon Monoxide detector requirements on page 56.
NOTICE
Flare Fireplaces Installation Guide- SIT Proflame 2
[Flare Double Corner, Left Corner, Right Corner, Front, See-Through, Passage, and Room Definer]
v18.7
FLARE REQUIRES INSTALLATION BE
PERFORMED BY AN NFI CERTIFIED INSTALLER,
OR A CERTIFIED FLAREAUTHORIZED
INSTALLER. INSTALLATIONS THAT DO NOT
FOLLOW THIS INSTRUCTION WILL NOT BE
COVERED BY WARRANTY OR SERVICED.

2 | P a g e
TABLE OF CONTENTS
SAFETY INFO AND WARNINGS.......................................................................................................................................5
FLARE FIREPLACES FRAMELESS IN EVERY WAY...........................................................................................................7
SAFETY .......................................................................................................................................................................7
CSA CERTIFICATION ................................................................................................................................................7
MANUAL MODEL LIST & INFORMATION .......................................................................................................................8
FIREPLACE OPERATION..................................................................................................................................................9
REMOTE CONTROL INSTRUCTIONS .......................................................................................................................................9
IFC Proflame 2 Remote buttons: .............................................................................................................................9
Remote control specification: ...............................................................................................................................10
Temperature indication display ............................................................................................................................10
Turning the system ON and OFF using the remote control ....................................................................................11
Remote Flame modulation ...................................................................................................................................11
Room thermostat option ......................................................................................................................................12
Smart room thermostat option.............................................................................................................................12
Fan Speed Control ................................................................................................................................................13
Continuous Pilot Ignition/Intermittent Pilot Ignition (CPI/IPI)................................................................................13
Key Lock ...............................................................................................................................................................13
Low battery power detection................................................................................................................................13
SIT BATTERY BACKUP -OPTIONAL SCREEN UNIT ONLY ....................................................................................................14
PAIRING REMOTE WITH FIREPLACE RECEIVER ........................................................................................................................15
Initializing the system for the first time.................................................................................................................15
Ignition Sequence .................................................................................................................................................15
WALL SWITCH OPTIONAL ..............................................................................................................................................16
MEDIA ARRANGEMENTS..................................................................................................................................................17
FEATURE REMOVAL.....................................................................................................................................................18
SAFETY SCREEN REMOVAL................................................................................................................................................18
EXTERNAL TEMPERED GLASS REMOVAL DOUBLE GLASS FIREPLACE........................................................................................19
INTERNAL CERAMIC GLASS REMOVAL...............................................................................................................................20
SIDE GLASS TRIM REMOVAL /INSTALLATION FLARE H&EH ................................................................................................22
REFLECTIVE BACK INSTALL...............................................................................................................................................23
INSTALLATION STEPS...................................................................................................................................................24
ACCESS PANEL..............................................................................................................................................................25
COMPONENT WHIP..................................................................................................................................................25
SIZING RECOMMENDATIONS....................................................................................................................................26
INSTALLATION PREPARATION .....................................................................................................................................27
FIREPLACE UNPACKING ...................................................................................................................................................27
FIREPLACE TELESCOPIC LEGS SETUP ............................................................................................................................28
LEG SETUP FOR FRONT AND SEE-THROUGH UNITS..............................................................................................................29
LEG SETUP FOR CORNER UNITS..........................................................................................................................................30

3 | P a g e
UNPACKING CONTROL UNIT AND ACCESSORIES......................................................................................................................31
FIREPLACE POSITIONING..................................................................................................................................................32
LED LIGHTS ..................................................................................................................................................................33
LED LIGHT INSTALL AND POWER ........................................................................................................................................34
LED CONTROLLER AND REMOTE ........................................................................................................................................35
OPTIONAL BLOWER KIT FOR SCREENED UNIT .............................................................................................................37
VENT TERMINATION....................................................................................................................................................38
VENT AND FIREPLACE SIZE................................................................................................................................................39
MINIMUM COMBUSTIBLE CLEARANCES FROM VENT................................................................................................................39
VERTICAL TERMINATION.................................................................................................................................................40
VENT TERMINATION CLEARANCES ..............................................................................................................................42
VENT RESTRICTOR SETUP .................................................................................................................................................43
CHIMNEY PATH INSTALLATION AND PLANNING .........................................................................................................44
FLARE 30/30H...........................................................................................................................................................45
FLARE 45/45H/45EH.................................................................................................................................................46
FLARE 50/50H/50EH.................................................................................................................................................47
FLARE 60/60H/60EH.................................................................................................................................................48
FLARE 70/70H/70EH.................................................................................................................................................49
FLARE 80/80H/80EH.................................................................................................................................................50
FLARE 100/100H/100EH ...........................................................................................................................................51
POWER VENTING.........................................................................................................................................................52
ELECTRICAL CONNECTION TO THE PV SYSTEM ......................................................................................................................54
GAS INSTALLATION......................................................................................................................................................55
GENERAL.....................................................................................................................................................................55
USING A REDUCER TO DE-RATE YOUR FLARE FIREPLACE.............................................................................................57
ADDING THE FLARE FIREPLACES DE-RATING REDUCER..............................................................................................58
ORIFICE SIZE.................................................................................................................................................................59
GAS VALVE ACCESS DOOR ................................................................................................................................................59
MANUAL GAS SHUTOFF ......................................................................................................................................59
LIQUID PROPANE USAGE IN FLARE FIREPLACES .....................................................................................................................60
COMMONWEALTH OF MASSACHUSETTS ..............................................................................................................................61
FLARE FIREPLACES - DOUBLE GLASS ............................................................................................................................62
OVERVIEW...................................................................................................................................................................62
DOUBLE GLASS -INSTRUCTIONS ........................................................................................................................................63
POWER REQUIREMENT ELECTRICAL REQUIREMENT ................................................................................................64
TELEVISION MOUNTING ABOVE FIREPLACE ................................................................................................................64
TV INSTALL FLAT EXAMPLE.....................................................................................................................................65
TV INSTALL LTYPE E ...............................................................................................................................................66

4 | P a g e
TV INSTALL RECESS 45 DEGREE ELBOW ON TOP OF THE UNIT .................................................................................67
TV INSTALL WITHOUT RECESS MANTEL INSTALLATION...........................................................................................67
CLEARANCES................................................................................................................................................................68
METAL FRAMING SPECIFICATIONS............................................................................................................................69
WOOD FRAMING SPECIFICATIONS............................................................................................................................69
CLEARANCES SPECIFICATION.............................................................................................................................................78
MANTEL CLEARANCE ......................................................................................................................................................79
CLEARANCE TO SPRINKLER...............................................................................................................................................80
HEAT RELEASES .............................................................................................................................................................81
AIR INTAKE ...............................................................................................................................................................81
EXAMPLES OF HEAT RELEASES...........................................................................................................................................82
SETTING UP YOUR FLARE FIREPLACE FOR ENHANCED OPERABILITY ...........................................................................83
KEEPING THE WALL ABOVE YOUR FIREPLACE AS COOL AS POSSIBLE.............................................................................................83
KEEPING YOUR DOUBLE GLASS AS COOL AS POSSIBLE..............................................................................................................84
FLARE FRONT,SEE THROUGH,AND CORNER FIREPLACE CLEARANCE ............................................................................................85
Flat –side and isometric view...............................................................................................................................85
L shape –side and isometric view .........................................................................................................................87
Side Overhang Specification on Left, Right, & Double Corner Fireplaces................................................................89
INDOOR/OUTDOOR KIT ................................................................................................................................................90
OUTDOOR KIT INSTALLATION CONSIDERATIONS.......................................................................................................90
OVERHANG REQUIREMENT ......................................................................................................................................91
OUTDOOR KIT FRAMING AND FINISH........................................................................................................................92
OUTDOOR KIT CLEARANCE TO NON-COMBUSTIBLE WALL.........................................................................................92
OUTDOOR KIT OPENING DIMENSIONS......................................................................................................................93
WEATHER-PROOF YOUR OUTDOOR KIT CAVITY ........................................................................................................94
BURNER DIMENSIONS .................................................................................................................................................95
HOME AUTOMATION ...............................................................................................ERROR! BOOKMARK NOT DEFINED.
ELECTRIC AND CONTROL .............................................................................................................................................96
ELECTRIC DIAGRAM -SCREEN .........................................................................................................................................97
DIAGRAM DOUBLE GLASS AND POWER VENT..................................................................................................................98
DOUBLE GLASS BOARD &LED LIGHT GUIDE.......................................................................................................................99
ELECTRIC DIAGRAM PV SYSTEM.....................................................................................................................................100
REPLACEMENT PARTS................................................................................................................................................101
MAINTENANCE..........................................................................................................................................................102
TORUBLESHOOTING ..................................................................................................................................................104
ADJUSTING YOUR AIR SHUTTER TO PREVENT SOOTING...........................................................................................................104
APPENDIX..................................................................................................................................................................105
MAINTENANCE LOG......................................................................................................................................................105
WARRANTY POLICY ......................................................................................................................................................106

5 | P a g e
SAFETY INFO AND WARNINGS
WARNING!
If the information in these instructions is not followed exactly, a fire or explosion may result causing property
damage, personal injury, or loss of life.
Installation and services must be performed by a qualified installer, service agency or the supplier.
The direct vent system appliance must be installed as an OEM installation in manufactured homes (USA only),
or an aftermarket permanently located, or a mobile home, where no prohibited by local codes and must be

Standard, Title 24 CFR, Part 3280, in the United States, or the Standard for Installation in Mobile Homes, CAN/
CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is supplied
with the appliance.
This product is listed to the ANSI standards for ANSI A21.50b-2009 / CSA 2.22b-2009 Vented Gas
Fireplaces CAN/ CGA 2.17-M91 Gas-Fired Appliance for use at high altitudes.
NEVER LEAVE CHILDREN OR ANY OTHER AT-RISK INDIVIDUAL ALONE WITH
THE APPLIANCE.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or
clothing ignition.
This appliance must be electrically wired and grounded in accordance with local codes, or in the absence of local codes,
with National Electric Code ANSI/NFPA 70 latest edition or the Canadian Electric Code CSA C22.1
A 110-120V AC Circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in locations such as bathrooms or near sinks.
State of California. Proposition 65 Warning. Fuels used in gas, wood-burning or oil-fired appliances, and the
products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and
other reproductive harm. California Health & Safety Code Sec. 25249.6

6 | P a g e
When an existing Category I heater is removed or replaced, the original venting system may no longer be sized to
properly vent the attached appliances. Instructions shall also indicate effects of an improperly sized venting
system (formation of condensate, leakage, spillage, etc.) and shall specify the following test procedure.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children,
and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at-risk
individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young
children, and other at-risk individuals out of the room and away from hot surfaces.
WARNING!
Proposition 65 Warning: Fuels used in gas, wood burning or oil-fired appliances, and the products of combustion of such
fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6. In the State of Massachusetts, only a licensed plumber and gas fitter may
install this product. See Note for the Commonwealth of Massachusetts.

7 | P a g e
FLARE FIREPLACES FRAMELESS IN EVERY WAY
Flare Fireplaces is where innovation, quality and luxury come together to form innovative ideas. By
combining superior raw materials, contemporary design, creative technology, and a frameless way of
thinking, we have created a full line of direct-vent fireplaces that are luxurious, simple to operate, and
efficient. Our modern gas fireplaces are distinguished by their clean linear design, superior built quality,
and unique features.
SAFETY
CSA CERTIFICATION
All our fireplaces are tested and have been certified to meet stringent CSA guidelines, ensuring optimum
quality, safety, and efficiency.
All our fireplaces have been certified and tested to work with Natural Gas or Propane.
Certification Information: CSA File # 263124
CSA/ANSI Z21.88--2019 - Vented Gas Fireplace Heaters
CSA CLASSES:
CLASS 2901 84 / CLASS 2901 04
All fireplaces are rated for commercial and residential use.
The CSA Mark
The Canadian Standards Association (CSA) is a nonprofit association serving business, industry, government
and consumers in Canada and the global marketplace. Among many other activities, CSA develops
standards that enhance public safety.
A Nationally Recognized Testing Laboratory, CSA is familiar with U.S. requirements. According to OSHA
regulations, the CSA-US Mark qualifies as an alternative to the UL Mark.
Here are some areas where CSA standards are applied:
•Canadian Electrical Code, Part III-Outside Wiring
•Electrical Engineering Standards
•Electromagnetic Compatibility

8 | P a g e
MANUAL MODEL LIST & INFORMATION
The Following manual should be used for the following Flare Fireplaces Models:
•Flare Front 30-100   (EH)
•Flare See-Through 30-  (EH)
•Flare Corner Right & Left 30- 
•Flare Double Corner 30- 
•Flare Room Definer 45-  (EH)
All models share the same gas valve system, remote, gas connection, and glass type, simplifying installation and
operation.
All warnings and instructions apply to all models.
Refer to the  name for specific model, clearance and installation information.
Flare Fireplaces should only be connected to M&G DuraVent or ICC 4x6 or 5x8 venting system. Refer to the specific
appliance model and size to determine vent size (Gas specification table) and chimney pathway requirements
(Chimney path installation & planning table). For detailed chimney installation information please use the M&G
DuraVent direct vent installation manual: http://www.duravent.com
For details on ICC direct vent installation, please use the ICC installation guide.
http://icc-chimney.com/en/exceldirect-support

Heating Appliances for Manufactured Homes and Recreatio

Installation MUST comply with local, regional, state, and national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities that have jurisdiction over restrictions, installation inspection and
permits.
This installation must conform to local codes. In the absence of local codes, you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.
Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified service technician, service agency or your dealer.
FLARE REQUIRES INSTALLATION BE
PERFORMED BY AN NFI CERTIFIED INSTALLER,
OR A CERTIFIED FLARE DEALER.
INSTALLATIONS THAT DO NOT FOLLOW THIS
INSTRUCTION WILL NOT BE COVERED BY
WARRANTY OR SERVICED.

9 | P a g e
FIREPLACE OPERATION
REMOTE CONTROL INSTRUCTIONS
IFC PROFLAME 2 REMOTE BUTTONS:
-Main ON/OFF switch
-Main Burner Flame Modulation 6 Levels
-Continuous or intermittent pilot mode (Intermittent is default)
-Thermostat or smart thermostat functions.
-Accent light modulation 6 levels (NOT USED).
-Mode Key (Flame Height, Lights, Smart Lock, Auxiliary Fan On/Off)
MUST BE ON
RGB LED Control

10 | P a g e
REMOTE CONTROL SPECIFICATION:
-Need 4.5 voltage supply.
-0-50 °C ambient temperature rating.
-315 MHz radio frequency.
TEMPERATURE INDICATION DISPLAY
-When the system is turned off the LCD screen will display the current room temperature in Fahrenheit
(°F) or in Celsius (°C.)
-To change from Fahrenheit (°F) to Celsius (°C) or vice versa press the thermostat key and the mode key
at the same time.

11 | P a g e
TURNING THE SYSTEM ON AND OFF USING THE REMOTE CONTROL
With the system OFF, press the ON/OFF Remote Key. The remote LCD will then
show other icons. At that time, the module will activate the appliance and a single
beep from the receiver will confirm reception command from the remote
When the system is ON, press the ON/OFF remote key, the remote LCD will show
the room temperature icon, at the same time the module will shut off the
appliance.
For information on using the remote and wall switch, click here.
REMOTE FLAME MODULATION
The Proflame 2 has 6 levels of modulation.
When the system is ON the flame level will be
at the maximum level.
By pressing the down arrow key once it will
reduce the flame height by one step.
Continued pressing of the down arrow will
result in the unit TURNING OFF. To return to
normal fireplace operation use the up-arrow
key to increase the flame height to HI.
If the up arrow has been pressed while the
system is ON, but the flame is OFF the flame
will come ON in the high position.

12 | P a g e
ROOM THERMOSTAT OPTION
The Remote control can operate as a room
thermostat. The thermostat can be set to a desired
temperature to control the room temperature. To
activate this option, press the thermostat key. The
thermostat icon on the LCD screen will display the
thermostat status is ON. The user can then set a suitable
temperature for the space. To adjust the desired
temperature, use the up or down arrow until the desired
temperature is displayed on the remote LCD screen.
SMART ROOM THERMOSTAT OPTION
The smart thermostat option will adjust the flame height
depending on the set temperature that has been set by the
user. When the room temperature gets close to the set
temperature the smart thermostat function will modulate
the flame down.
To activate the smart thermostat function, press the
thermostat key while the appliance is on until the word
SMART appears beside the icon of the thermostat.
To adjust the set temperature, press the up or down arrow
keys until the desired temperature is displayed on the LCD.
Note that: when the smart thermostat is activated, the flame level modulation is not activated.

13 | P a g e
FAN SPEED CONTROL
This feature is not used with the Flare fireplaces.
CONTINUOUS PILOT IGNITION/INTERMITTENT PILOT IGNITION (CPI/IPI)
By default, the Flare Fireplace is setup for IPI operation, but this can be
changed to CPI on screen units only. When the system is OFF pressing the
Mode key to index to CPI mode icon. Press the UP arrow will select the CPI
mode (but it is still not activated.) There is also a switch on the CPI/IPI that is
located on x5 port in the module. Pressing down arrow key will activate the IPI
mode at the same time turn the IPI/CPI switch in X5 port on the module. A
single beep will confirm the command.
KEY LOCK
To avoid unsupervised operation of the remote control this feature has been created. To activate this
feature, press the mode and up arrow at the same time. A lock icon will appear in the LCD screen. To
deactivate this feature, press the mode and up arrow at the same time.
LOW BATTERY POWER DETECTION
The life of the remote batteries depends on
-Battery quality
-Number of ignitions of the appliance
-The number of actions on the remote control
When the remote battery is low an empty battery icon will appear on the LCD Screen
CAUTION: DO NOT USE a screwdriver or other metallic object to remove the batteries from the battery box! This could cause a
short circuit to the system.

14 | P a g e
SIT BATTERY BACKUP -OPTIONAL SCREEN UNIT ONLY
Batteries Remote
•4 x AA (alkaline recommended).
•Low battery indicator on handsets with display.
•Battery replacement is recommended after 1 years.
Batteries Receiver
•
•An AC Mains Adapter may be connected in addition to batteries.
•Without using a mains AC adapter, battery replacement is recommended at the beginning of each heating season as part of
the yearly service check.
•Battery pack to be used with screen units only. Will not work on double glass units.
•Battery pack attaches to X5 cable at black end cap.

15 | P a g e
PAIRING REMOTE WITH FIREPLACE RECEIVER
Your remote will come paired with the fireplace receiver to allow for operation out of the box. In the event of a
remote or receiver replacement, use the following procedure to pair the remote with the receiver:
INITIALIZING THE SYSTEM FOR THE FIRST TIME
-Install 3 AAA type batteries in the remote battery bay located on the remote back.
-Press the SW1 button on the module see the following figure, the module will beep 3 times to indicate
that it is ready to synchronize with the remote.
-Press the ON/OFF button in the remote, the module will beep 4 times to indicate that the remote and the
module are synchronized to each other.
IGNITION SEQUENCE
Starting from OFF, press the remote power button. Four seconds after it is pushed the SIT module will send spark to
the pilot hood, and spark for 60 seconds. If there is no flame ignition during the first ignition sequence, the SIT module
will stop sparking for approximately 35 seconds and then begin sparking again. The second attempt will spark for 60
seconds. If there is no positive ignition after the second sequence the SIT module will go into a Lock Out and the LED
Indicator Light will blink three times in intervals until the system is reset.
- Ignition sequence will spark for 60 seconds, followed by a 35 second wait, 60 second spark and then lock out if flame
is not ignited.
- The lock out will blink on the LED indicator light will blink three times.
Reset Using the Transmitter ON/OFF power button: Turn the system off by pressing the remote power button. After
approximately 2 seconds press it again
Low Battery Condition (<4V) Remote Control: Battery icon will appear on LCD remote control display. Replace
batteries.
Low Battery Condition (<4V) Battery Backup: Red LED Indicator will blink (1) time in intervals. Low double-beep emit-
ted from SIT control module when it receives an ON/OFF command from the remote control. Replace Batteries.
Pilot Flame Error Condition: Red LED Indicator will blink (2) times in intervals. Contact your dealer if this occurs.
System Lock Out Condition: Red LED Indicator will blink (3) times in intervals. Make sure gas is turned on and sensor is
not shorted. Follow Reset Using the Transmitter ON/OFF power button instructions above.

16 | P a g e
WALL SWITCH OPTIONAL
In case of losing the remote control or empty batteries, there is another option to control the fireplace which is
located on the X8 port of the IFC module which the WALL SWITCH. The following operation can be done from the wall
switch:
-Turn ON fireplace
-Turn OFF fireplace
Note: Flare Fireplaces supplies each fireplace a wall
switches and a remote control to control the unit. Please
note, only one device should be used in a cycle of
powering the unit on and off. If you utilize the remote
control to power the appliance on, use the remote to
also power the unit off.
Trying to utilize different methods in a cycle could result
in one method failing to control unit until appliance has
been powered down and the cycle ended.
SIT wall switch can be run with up to 100 FT of wire.

17 | P a g e
MEDIA ARRANGEMENTS
Flare Fireplaces can be equipped with different media types. Follow the instructions below for information on how to
add and arrange media in your Fireplace. Click here for Media Calculation Guide
•Do not place any type of media on the pilot or in front of the pilot. Keep 1”distance from the pilot to allow
correct operation of the pilot.
•Media can be put over the Flare burner. Avoid placing media over the main burner ports as it may disrupt
flame in case of a clogged port. Avoid placing driftwood arching over burner, instead place in front or behind.
•If using media that was not supplied by Flare Fireplace, make sure that the media is certified/suitable to be
used in direct vent gas fireplaces.
•Keep the pilot front cover view open to be able to view the pilot spark and flame from outside.
•Fireglass:
a. Fire Glass may be used.
b. When the fireplace viewing window is open, and media is placed, make sure Fire Glass does not fall
on the ceramic glass lower frame as that may cause breakage when putting back the ceramic glass.
c. Make sure pilot is clear of any Fire Glass particles.
d. Flare Fire Glass can be put safely into the firebox. Avoid overloading the burner with Fire Glass,
specifically over the main burner ports.
•Maintain minimum distance the fireplace glass panels.
•Use the manual for instructions on how to remove, replace, & arrange the fireplace glass media
PROPER DRIFTWOOD PLACEMENT IMPROPER DRIFTWOOD PLACEMENT
Ceramic Pebbles Fireglass
CHOKING HAZARD! Ensure that the fireplace area is clear of fire glass particles as these could be ingested by small
children. Vacuum area after installation

18 | P a g e
FEATURE REMOVAL
SAFETY SCREEN REMOVAL
Follow the instructions below for safety screen removal.
PLEASE NOTE: Safety screen may be shipped separately from the appliance.
The barrier is designed to reduce the risk of burns from the hot viewing glass and is
provided with this appliance. It must remain installed for the protection of children and
other at-risk individuals.
Do NOT operate the fireplace without the safety screen barrier.
Front, See Through, and Corner Units
•Safety screen removal requires no tools.
•Push the top frame of the screen up until it clears the bottom of the opening.
•Tilt the bottom of the screen out and pull down so the top frame clears the opening.

19 | P a g e
EXTERNAL TEMPERED GLASS REMOVAL DOUBLE GLASS FIREPLACE
Follow the procedure below to remove and install back the fireplace external glass (double glass fireplace configuration).
Note: Suction cups are needed to remove the glass.
Warning! Turn off the fireplace and allow time for the unit to cool before proceeding.
Caution: The glass is very fragile and should be handled with care.
Warning! Double glass fireplace should NOT be operated without the external glass
•Confirm lock screws have been removed during install (should be done once, during install only).
•Attach glass suction cups 
•Using suction cups, slightly push in the external glass top edge.
•Once glass has been pushed, slightly lift the glass to clear bottom part of the glass.
•Remove the glass and place in a secure location.
Install back external glass
•Attach glass suction cups to the glass. Use more t)
•Place upper edge of the glass in position and push latching trim.
•Once trim has been pushed in, slide glass top in position.
•Tilt in bottom edge of the glass in position as you are lifting the glass up.
•Glass is now secure in place. No bolts are needed to lock the glass.

20 | P a g e
INTERNAL CERAMIC GLASS REMOVAL
Follow the procedures below to remove and install the internal ceramic glass (double glass fireplace configuration).
Warning! Turn off the fireplace and allow time for the unit to cool before attempting to remove the glass.
CAUTION:The ceramic glass is very fragile and should be handled with care.
CAUTION: Do not operate the appliance with glass removed, cracked, or broken. Replacement of the panel(s) should
be done by a licensed or qualified service person.
TECHNICIANS
Step 1 Remove the bottom, left, and right magnetic trim pieces, place in a secure location to prevent damage.
Step 2 Locate and loosen the hand screws within the top frame of the fireplace. These will loosen the top butterfly
trim, releasing the glass from the inner gasket, preparing it for removal.
Step 3 Locate and loosen the hand screws, on the right, within the frame of the fireplace. These will loosen the right
trim which can be removed and set aside to prevent any damage.
Step 4 Locate and loosen the hand screws, on the left, within the frame of the fireplace. These will loosen the left
trim which can be removed and set aside to prevent any damage.
Step 5 Locate and loosen the hand screws, on the bottom, within the frame of the fireplace. These will loosen the
bottom trim which can be removed and set aside to prevent any damage.
Step 6 Attach your suction cup(s) to the inner layer of glass. Once secure, lift, clearing the bottom frame. Pull out
and down to clear top frame, and lay glass on a soft flat surface in a safe location.
WHEN REINSTALLING YOUR GLASS DO NOT OVERTIGHTEN THE HAND SCREWS SECURING THE TRIM
AGAINST THE GLASS.
Step 1 Step 2