Flare Fireplaces Flare-VFF-50 User manual

1
NOTICE
FOR OUTDOOR USE ONLY
WARNING: If the information in these instructions is not
followed exactly, a fire or explosion may result, causing
property damage, personal injury, or loss of life.
-Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS
-Do not try to light any appliance.
-Do not touch any electrical switch; do not use any
phone in your building.
-Immediately call you gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
-If you cannot reach your gas supplier, call the fire
department.
-Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Installation and service of this appliance MUST be performed by qualified certified NFI personnel.
Massachusetts: The piping and final gas connection must be performed by a licensed plumber or gas
fitter in the State of Massachusetts. Also, see Carbon Monoxide Requirements Detector requirements.
Flare Fireplaces Vent-Free Outdoor Installation Guide
Flare Double Corner, Left Corner, Right Corner, Front and See-Through v15.0

2
TABLE OF CONTENTS
FIREPLACE SAFETY WARNINGS................................................................................................................................................... 4
FLARE VENTLESS FIREPLACES –FRAMELESS IN EVERY WHERE....................................................................................................13
CERTIFICATION.........................................................................................................................................................................13
INSTALLATION MODEL LIST AND INTRODUCTION......................................................................................................................14
WATER AND MOISTURE RESISTANCE........................................................................................................................................15
QUALIFIED INSTALLING AND INSTALLERS..................................................................................................................................15
HIGH ALTITUDES......................................................................................................................................................................15
WELL HEAD GAS INSTALLATIONS..............................................................................................................................................16
OUTDOOR FIREPLACE INSTALLATION OVERVIEW.......................................................................................................................16
OUTDOOR FIREPLACE ENCLOSURE REQUIREMENTS..................................................................................................................16
DRAINAGE AND VENTILATION..................................................................................................................................................18
CLEARANCES............................................................................................................................................................................19
CLEARANCES TO COMBUSTIBLE FRAMING................................................................................................................................19
CLEARANCES TO COMBUSTIBLE FINISHING MATERIALS ............................................................................................................19
MANTEL CLEARANCE................................................................................................................................................................21
ELECTRICAL REQUIREMENTS.....................................................................................................................................................22
ON/OFF SWITCH ......................................................................................................................................................................22
ON/OFF REMOTE .....................................................................................................................................................................22
GAS CONNECTION....................................................................................................................................................................23
SERVICE ACCESS PANEL:...........................................................................................................................................................23
LIQUID PROPANE GAS CONVERSION ........................................................................................................................................24
PROPANE GAS CYLINDER/TANK –DIRECTLY CONNECTED TO FIREPLACE ...................................................................................24
WATERPROOF ELECTRICAL CONNECTION.................................................................................................................................25
ELECTRICAL DRAWING FOR INSIDE VENTLESS CORE..................................................................................................................26
VENTLESS POWER BOARD........................................................................................................................................................27
RGB LED LIGHTS.......................................................................................................................................................................28
MEDIA ARRANGEMENT............................................................................................................................................................29
WIND GUARD GLASS INSTALLATION.........................................................................................................................................30
RAIN DOORS ............................................................................................................................................................................32
REFLECTIVE BACK INSTALLATION..............................................................................................................................................33
INSTALLATION STEPS................................................................................................................................................................34
FIREPLACE UNPACKING............................................................................................................................................................35
REPLACEMENT PARTS LIST .......................................................................................................................................................35
MAINTENANCE.........................................................................................................................................................................36
YEARLY SERVICE PLAN..............................................................................................................................................................37
MAINTENANCE LOG.................................................................................................................................................................38

3
WARRANTY POLICY...................................................................................................................................................................39
18 MONTH COMPREHENSIVE WARRANTY................................................................................................................................39
LIMITED FIVE-YEAR COVERAGE.................................................................................................................................................39
LIMITED 10-YEAR COVERAGE ...................................................................................................................................................39
CONDITIONS............................................................................................................................................................................39
EXCLUSIONS.............................................................................................................................................................................40
WARRANTY VOID WHEN…........................................................................................................................................................40

4
FIREPLACE SAFETY WARNINGS
DANGER, CARBON MONOXIDE HAZARD!
This appliance can produce carbon monoxide, which has no odor. Using it
in an enclosed space can kill you. Never use this appliance in an enclosed
space such as a camper, tent, car, or home.
Do not try to light this appliance without reading the “LIGHTING” instructions section of this
manual. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of
this or any other appliance. An L.P. cylinder not connected for use must not be stored in the
vicinity of this or any other appliance. If the information in these instructions is not followed
exactly, a fire or explosion may result, causing property damage, personal injury, or death.
DANGER! IF YOU SMELL GAS
•Shut off gas to the appliance.
•Extinguish any open flame.
•If odor continues, keep away from the appliance and immediately call your gas supplier
or fire department.
FOR OUTDOOR USE ONLY!
WARNING
WARNING
WARNING
WARNING

5
DANGER! HOT GLASS
Hot glass and surface will cause burns. Do not touch glass until cooled.
Never allow children to touch glass or surface surrounding the fireplace.
COVER MUST BE REMOVED DURING OPERATION
Improper installation, adjustment, alteration, service, or maintenance can cause property
damage, personal injury, or loss of life. Refer to the owner’s installation manual provided
with this appliance. Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or
any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity
of this or any other appliance.
DANGER
Carbon Monoxide Hazard
This appliance can produce Carbon
Monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed
space such as a camper, tent, car, or home.
WARNING
WARNING
WARNING

6
SAFE OPERATING PRACTICES
•This appliance is hot when operating and can cause severe burns if contacted.
•Installation and repair should be done by a qualified service person. The appliance should be inspected before
use and at least annually by a qualified service person. More frequent cleaning may be required, as necessary.
It is imperative the control compartment, burners and circulating air passageways of the appliance be kept
clean.
•Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fire or injury.
•Risk of burns. The appliance should be turned off and cooled before servicing.
•Do not install damaged, incomplete or substitute components.
•Young children should be carefully supervised when they are in the appliance. Toddlers, young children, and
others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk
individuals in the vicinity. To restrict access to an appliance or stove, install an adjustable safety gate to keep
toddlers, young children, and other at-risk individuals out of the vicinity and away from hot surfaces.
•Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot
surfaces
•Under no circumstances should this appliance be modified.
•Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all
plastic bags, these are not a toy and should be kept away from children and infants.
•Do not leave appliance unattended when in use.
•This appliance must not be used for cooking.
•This unit is not for use with solid fuel.
•Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage.
Read the installation, operating and maintenance instructions thoroughly before installing or servicing this
equipment.
•This appliance shall be used ONLY outdoors in a well-ventilated space and shall NOT be used inside a building,
garage, or any other enclosed area.
•Cylinders must be stored outdoors in a well-ventilated area out of reach of children. Disconnected cylinders
must have threaded valve plugs tightly installed and must not be stored in a building, garage, or any other
enclosed area.
•Storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply (Natural
gas line or LP gas cylinder).
•If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the appliance
being put into operation.
•Clothing or other flammable materials should not be hung from the appliance or placed on or near the
appliance.
•Any guard or other protective device removed for servicing the appliance must be replaced prior to operating
the appliance.
•Inspect the fuel supply connection for signs of leakage (Including the hose for LP models) before each use of
the appliance.

7
•The pressure regulator and hose assembly supplied with LP models must be used. Replacement pressure
regulators and hose assemblies must be those specified in this manual.
•The LP gas supply cylinder used with LP models must be constructed and marked in accordance with the
specifications for LP-gas cylinders as required by the U.S. Department of Transportation (DOT) or the
Canadian Transport Commission (CTC).
•The LP gas cylinder supply system must be arranged for vapor withdrawal.
•The LP-gas cylinder used must include a collar to protect the cylinder valve.
•When an LP model is not in use, the LP-gas must be turned off at the supply cylinder.
•To extend the life of your appliance, protect and cover it from the elements when not in use.
•This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of
Massachusetts
CAUTION: The gas pressure regulator provided with this appliance must be used. This regulator is set
for an outlet pressure of 7-8 (NG) 10-11 (LPG) inches water column
When turning fireplace on/off visually confirm flames start and extinguish completely before leaving
appliance.
CAUTION! SAFE UNPACKING
During unpacking and assembly, we recommended you wear work gloves and
safety glasses for your protection. Although we make every effort to make
the assembly process as problem free and safe as possible, it is characteristic
of fabricated steel parts that the edges and corners might be sharp and could
cause cuts if handled incorrectly.
WARNING
WARNING
WARNING

8
This appliance is designed for non-combustible enclosures only and must be installed and
serviced by a qualified installer to local codes.
Minimum clearance to combustibles must be maintained or a serious fire hazard could result.
Use only non-combustible materials (certified to ASTM E-136) such as steel studs, cement board,
ceramic tile, marble, paint etc. When adding finishing materials to the appliance. Do not use
wood, or drywall.
You must have clear and easy access to the on/off valve after the appliance is installed and
connected to the gas supply to safely turn off the burner.
Mantel temperatures will rise above normal temperatures and may be hot to the touch.
Cover must be removed when burner is in operation.
CAUTION! Wind Cover
External Wind Covers should only be used when the fireplace is not operating
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING

9
RISKOF FIRE, EXPLOSION, OR ASPHYXIATION, ENSURE THERE ARE NO IGNITION SOURCES SUCH AS SPARKS OR OPEN FLAMES.
The installation must be performed by a licensed gas fitter, and all connections must be leak tested before
operating the appliance.
•All gas connections must be contained within the appliance when complete.
•High pressure will damage the valve, disconnect gas supply piping before testing gas line at test pressures
above 1/2 PSIG.
•Connect the gas supply in accordance with local codes. In the absence of local codes, install to the current
CAN/CSA B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI Z223.1/NFPA 54
in the United States
•Leak test all the connections by brushing on a soap and water solution. These connections can be accessed by
removing the burner. (See burner removal instructions.)
•Make sure cylinder valve is in its full off position. (Turn clockwise to stop).
•Check cylinder valve features to ensure it has proper external mating threads. (Cylinder Valve Marked: USE
WITH TYPE 1)
•Inspect hose shipped with the unit for damage. Never attempt to use damaged or plugged equipment. See
your local LP Gas Dealer for repairs.
•When connecting regulator assembly to the cylinder valve, hand tighten black QCC1 nut clockwise to a
positive stop. DO NOT use a wrench to tighten. Use of a wrench may damage the quick closing coupling nut
and result in a hazardous condition.
•Locate the hose out of pathways where people may trip over it or in areas where the hose may be subject to
accidental damage.
•Open cylinder valve fully (counterclockwise). Turn the on/off valve at the unit slowly to the on position and
use a soapy water solution to check all connections for leaks as indicated in the diagrams before attempting
to light the appliance. If a leak is found, turn tank valve off and do not use the appliance until repairs can be
made.
•Use only a ground fault interrupter (GFI) protected circuit with this outdoor gas appliance.
•Ensure that all power sources have been shut off prior to beginning any electrical work.
•Do not use this appliance if any part has been under water. Call a qualified
•Service technician immediately to have the appliance inspected for damage to the electrical circuit.
•All wiring should be done by a qualified electrician and shall follow local codes. In the absence of local codes,
use the current csa22.1 Canadian electric code in Canada or the current national electric code ANSI/NFPA no.
70 in the United States.
•Children and adults should be alerted to the hazards of high surface temperatures and should stay away from
the appliance to avoid burns or clothing ignition.
•Children should be carefully supervised when they are in the appliance.
•Clothing or other flammable materials should not be hung from the appliance or placed on or near the
appliance. The area above the enclosure may be extremely hot. Direct contact with these surfaces should be
avoided to prevent burns or clothing ignition.
WARNING

10
•Any guard or protective device removed for servicing the appliance must be replaced prior to operating the
appliance.
•Installation and repair should be done by a qualified service person.
•The appliance should be inspected before each use and at least annually by a qualified service person. More
frequent cleaning may be required, as necessary. It is imperative that the control compartment, burners and
circulating air passageways of the appliance be kept clean.
•Never use the appliance while it is raining.
•Always turn the appliance off when raining.
•Never splash any liquid on the glass / glass embers when the appliance is operating.
•The glass / glass embers will be extremely hot while operating, never try to touch them.
•Always ensure the appliance stands firmly on level ground.
•Never use the appliance if the burner is damaged. Inspect the burner before each use. Ensure that no debris
such as leaves; grass or other objects have entered or are on the appliance. If the burner is damaged, it must
be replaced prior to using the appliance with a replacement burner specified by your Flare dealer.
•Inspect the hose assembly before each use. If there is evidence of excessive abrasion or wear, or if the hose is
damaged it must be replaced prior to using the appliance with a replacement hose assembly specified by your
Flare dealer.
To avoid the possibility of burns conversions should only be done when the appliance is cool. Ensure the
burner is turned off. Turn the gas off at source and disconnect the appliance before beginning conversion.
Glass embers may have sharp edges wear safety glasses and gloves when handling.
This conversion must be performed by a licensed gas fitter, and all connections must be
leak tested before operating the appliance.
WARNING
WARNING
WARNING

11
Glass embers may have a fine oil residue that needs to be cleaned prior to installation.
Clean the glass with mild dish soap, drain, rinse thoroughly and dry before installing. Glass
embers may have sharp edges, wear safety glasses and gloves when handling. Do not
change or substitute the glass ember material provided with this appliance. If replacing,
use only replacement glass embers available from your local authorized dealer/distributor.
Real rocks must not be used in this appliance. Heat will cause them to explode.
Keep face and body away from burner area when lighting. Ensure burner controls are in
the off position. Slowly turn on the gas supply valve. The propane cylinder is equipped
with an excess flow device. Unless burners are turned off prior to turning the cylinder
on, only small flames and low heat will be achievable. If the burner does not light within
10 seconds, turn the valve off and wait 5 minutes for any gas to dissipate before
repeating the procedure.
WARNING
WARNING

12
•Never use this appliance for other than the intended use. Do not use this appliance to
prepare food.
•You must have clear and easy access to the on/off valve AFTER the appliance is installed and
connected to the gas supply to safely turn off the burner.
•Never use this appliance for other than the intended use. Do not use this appliance to
prepare food. N
•You must have clear and easy access to the on/off valve AFTER the appliance is installed and
connected to the gas supply to safely turn off the burner.
•Do not bypass thermocouple safety.
•Do not operate the appliance if any part has been under water. Immediately call a qualified
service technician to inspect the appliance and replace any part of the control system and
any gas control, which has been underwater.
•the gas control is exposed to water in any way, DO NOT try to use the appliance. The gas
control must be replaced.
•Hose: Check for abrasions, melting, cuts, and cracks in the hose. If any of these conditions
exist, do not use the appliance. Have the part replaced by your fireplace dealer or qualified
gas installer.
•To avoid the possibility of burns, maintenance should be done only when the appliance is
cool. Avoid unprotected contact with hot surfaces. Ensure burner is turned off. Turn gas off
at source and disconnect the appliance before servicing. Clean the appliance in an area
where cleaning solutions will not harm decks, lawns, or patios. Do not use flammable,
corrosive, or abrasive cleaners.
•The appliance area must be clear and free from combustible materials, gasoline and other
flammable vapors and liquids. Do not obstruct the flow of combustion and ventilation air.
Keep the ventilation opening of the cylinder enclosure free and clear of debris.
•Disconnect the power supply from the appliance before servicing. Turn off the appliance
completely and let cool before servicing. Only a qualified service person should service and
repair this electric appliance.
The appliance has been designed with several safety features, which include a safety valve. If
the burner flame is extinguished the appliance will automatically shut down. Any modification
to the appliance may compromise the safety of this appliance. Special concern is as follows.
Initial Lighting: When lit for the first time, the appliance emits a slight odor. This is a normal
temporary condition caused by the “burn-in” of internal paints and lubricants used in the
manufacturing process and does not occur again. Simply run the main burner on high for
approximately one-half hour.
WARNING

13
FLARE VENTLESS FIREPLACES –FRAMELESS IN EVERY WHERE
Flare Fireplaces is where innovation, quality and luxury come together to form new ideas. By combining superior
raw materials, contemporary design, creative technology, and a frameless way of thinking, we have created a
full line of direct-vent fireplaces that are luxurious, simple to operate, and efficient. Our Fireplaces are
distinguished by their clean design, superior build quality and unique features.
CERTIFICATION
All our fireplaces are tested and have been certified to meet stringent CSA guidelines, ensuring optimum quality,
safety, and efficiency. All our fireplaces have been certified and tested to work with Natural Gas or Propane.
Certification Information:
ANSI Z21.97/CSA 2.41 for Outdoor Gas Fireplaces
All fireplaces are rated for commercial and residential use.
The CSA Mark
The Canadian Standards Association (CSA) is a nonprofit association serving business, industry, government and
consumers in Canada and the global marketplace. Among many other activities, CSA develops standards that
enhance public safety.
A Nationally Recognized Testing Laboratory, CSA is familiar with U.S. requirements. According to OSHA
regulations, the CSA-US Mark qualifies as an alternative to the UL Mark.
Here are some areas where CSA standards are applied:
•Canadian Electrical Code, Part III-Outside Wiring
•Electrical Engineering Standards
•Electromagnetic Compatibility

14
INSTALLATION MODEL LIST AND INTRODUCTION
The following manual should be used for the following Flare Outdoor Vent-Free Fireplaces 50 to 100 inch long.
The Flare Fireplaces Outdoor Vent-Free fireplace can be ordered in the following configurations:
•Flare Vent-Free Front 50” - 100“
•Flare Vent-Free See-Through 50” - 100“
•Flare Vent-Free Corner Right & Left 50” - 100“
•Flare Vent-Free Double Corner 50” - 100“
All Outdoor Vent Free Flare Fireplaces are made using a combination of 3.16 & 3.04 stainless steel. All models
share the same gas valve system, gas connection, glass type and burner, simplifying installation and operation.
All warnings and instructions apply to all models. Refer to the model’s name for specific model, clearance and
installation information.
1. Installer must leave instruction manual with owner after installation.
2. Installer must have owner fill out and mail registration card supplied with this fireplace or register online at
https://www.flarefireplaces.com
3. Installer should show owner how to start and operate outdoor fireplace. Always consult your local Building
Department regarding regulations, codes or ordinances which apply to the installation of an outdoor gas
fireplace.
This series is design certified in accordance with ANSI Z21.97/CSA 2.41 for Outdoor Gas Fireplaces and should
be installed according to these instructions. Any alteration of the original design, installing it other than as
shown in these instructions or using a type of gas not shown on the rating plate, is the responsibility of the
person and company making the change.
Installation MUST comply with local, regional, state, and national codes and regulations. Consult insurance
carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation
inspection and permits.
This installation must conform to local codes. In the absence of local codes, you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified service technician, service agency or your dealer.

15
WATER AND MOISTURE RESISTANCE
-This outdoor fireplace will shed moderate amounts of water but is not waterproof. Water and condensing
water vapor may enter the chase under certain conditions. Do not locate appliance where it can get
excessively wet.
-The fireplace will not perform as an exterior wall. Moisture penetration must be considered for construction
that places the fireplace in structure walls or on moisture sensitive surfaces. When installed on exterior
walls: Flare Fireplaces recommends the fireplace chase be constructed outside the structure's weather
envelope. Where the platform meets the wall, use a flashing detail like that required for attached decks.
-Chase platforms, including hearths should slope away from the structure at 1/4 in. per foot. The fireplace
can be shimmed level. When installed on surfaces where water may collect or cause damage: Flare
Fireplaces recommends a slope of 1/8 to 1/4 in. per foot towards the drain port suggested.
-Hearths should slope away from the front of the fireplace and chase at 1/8 in. to 1/4 in. per foot. Metal
safety strips must be on top of any combustible hearth materials used for moisture management. When
purchasing a firebox or fireplace we recommend you also buy a weather cover to protect the unit from
moisture. Never install a burner where moisture cannot drain off easily. We recommend a weather barrier
to protect the burner from moisture.
-Do not use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the unit and to replace any part of the control system and any gas control, which has been
underwater.
QUALIFIED INSTALLING AND INSTALLERS
-Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing
of equipment shall be performed only by a qualified agency. The term "qualified agency" means any
individual, firm, corporation, or company which either in person or through a representative is engaged in
and is responsible for (a) the installation or replacement of gas piping or (b) the connection, installation,
repair, or servicing of equipment, who is experienced in such work, familiar with all precautions required and
has complied with all the requirements of the authority having jurisdiction.
-Commonwealth of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the
Commonwealth of Massachusetts
-The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1. * *Available from the American National Standards Institute, Inc. 1430 Broadway, New
York, N.Y. 10018.
HIGH ALTITUDES
-For altitudes/elevations above 2,000 feet (610m), ratings should be reduced at the rate of 4 percent for each
1,000 feet (305m) above sea level.

16
WELL HEAD GAS INSTALLATIONS
-Some natural gas utilities use "well head" gas. This may affect the Btu output of the unit. Contact the gas
company for the heating value. Contact the manufacturer or your gas company before changing spud/orifice
size.
OUTDOOR FIREPLACE INSTALLATION OVERVIEW
When selecting a location for your appliance it is important to ensure clearances to adjacent combustibles are
met. This appliance is intended for installation on an outdoor patio or in your yard. It is highly recommended
that this appliance be installed in a sheltered area (following the guidelines outlined below). Direct wind will
cause an erratic flame and possible pilot or main burner outage. An erratic flame could also lead to excessive
black soot, this condition is not a safety issue but is visually undesirable.
1. Fireplace Gas type: Natural Gas or Propane.
2. Combustible’s proximity and clearances to the fireplace.
3. 120V GFCI power outlet or direct connection for the electronic ignition and LED lights.
4. Gas shutoff valve location.
5. Verify ventilation meets at least minimum requirements
6. Wind and rain direction
7. Drainage under fireplace.
8. Drain pan and weather door accessories.
OUTDOOR FIREPLACE ENCLOSURE REQUIREMENTS
Do not install fireplace until all necessary provisions are made for combustion and ventilation air. Consult the
written instructions provided with the fireplace for information concerning combustion and ventilation air. In the
absence of instructions, refer to the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and
Ventilation, or applicable local codes.
With walls on all sides, but at least one
permanent opening at ground level and no
overhead cover:
Within a partial enclosure that includes an
overhead cover and more than two walls, the
following shall apply:
• at least 25% of the total wall area is
completely open, and
• at least 30% of the remaining wall area is
open and unrestricted.
In the case of balconies, at least 20% of the
total wall area shall be and remain open and
unrestricted.

17
Within a partial enclosure which includes an overhead cover and no more than two side walls. These side walls
may be parallel, as in a breezeway or at right angles to each side.
Within a partial enclosure which includes an overhead cover and three sidewalls if 30 percent or more of the
horizontal periphery of the enclosure is permanently open.
This fireplace is intended for installation on an outdoor patio or yard. This fireplace shall
be used only outdoors in a well-ventilated space and shall NOT be used in a building,
garage, or other enclosed area. This fireplace cannot be installed with an opening to the
inside of a residence. Connection directly to an unregulated L.P. tank can cause an
explosion. Risk of fire, explosion, or asphyxiation. Ensure no ignition, flame or spark are
near during installation. This includes cigarettes or cell phones.
WARNING

18
DRAINAGE AND VENTILATION
Flare Fireplaces recommends leaving the included Storm Doors on the fireplace when it is not in use, to prevent
any accumulation of moisture inside the unit. Although the fireplace is designed to operate outdoors safely, rain
and other sources of moisture may enter the fireplace cavity, which may cause water to collect inside the chase
and base of the unit within the fireplace enclosure.
When choosing a location for your fireplace, care must be taken to avoid areas where excessive moisture or
running water may become an issue. To prevent moisture or water from collecting underneath the fireplace, the
builder must provide a means to drain water from under the fireplace. This needs to happen before positioning the
fireplace in its location. It is recommended that a sealed corrosion resistant drain pan with provisions for drainage
be positioned underneath the fireplace. Flare has over 55 models of fireplaces, so the drainage size will vary from
project to project. The depth of the fireplaces does not change between each model, however the length does. We
must account for the length of each individual fireplace to ensure the drainage pan will collect all running water
that may accrue inside this unit.
When planning for the installation of the fireplace the framing height must be increased to accommodate a drain
pan and any additional drainage piping required. The drain pan needs to be constructed from corrosion resistant
metal, or other suitable materials such as an ice and water shield membrane. A means of drainage out of the drain
pan such as piping, or weep holes must also be provided. A slope of 1/4” (6mm) per foot towards the drain port is
recommended. Note: The fireplace must be installed on a level surface to ensure proper drainage. It is the
responsibility of the builder to ensure proper drainage provisions have taken place. The Flare unit drains from the
center of the fireplace, using slotted holes provided. You can see a drawing of this below.
Ventilation under the unit is also needed to allow air movement and proper evaporation of moisture under the
fireplace. Please plan for an area of 70 Sq. inch for air ventilation under the fireplace. Ventilation will allow the
chase to dry and prevent moister issues.
Flare Fireplaces recommend building a rectangular frame only platform, studs only, to allow water to exit the
fireplace and drop down to a slope or drain pan.
NOTE: Although the builder should plan for a slot to drain water, the fireplace must be installed leveled.
VENT FREE FIREPLACE –BOTTOM VIEW –DRAIN PLUGS

19
CLEARANCES
CLEARANCES TO COMBUSTIBLE FRAMING
TOP: 4”
BOTTOM: 0”
SIDE: 2”
BACK: 2”
COMBUSTIBLE PERPENDICULAR SIDE-WALL: 36”
FRONT OF FIREPLACE TO COMBUSTIBLES: 36”
CLEARANCES TO COMBUSTIBLE FINISHING MATERIALS
LETTER
DESCRIPTION
CLEARANCE TO COMBUSTIBLE
A.
FROM GROUND OR OTHER CONBUSTIBLE SURFACE
11”
B.
FROM SIDE WALLS
6”
C.
*FROM CEILING (MINIMUM)
36”
D.
ALCOVE WIDTH (MINIMUM)
Fireplace Length + 12”
E.
ALCOVE DEPTH (MAXIMUM)
24” (MAXIMUM)
F.
NON-COMBUSTIBLE BOARD ABOCE FIREPLACE OPENING
8”
*Minimum clearance to the ceiling does not apply when the unit is installed with no overhead construction.

20
LETTER
DESCRIPTION
MEASUREMENT FROM OPENING
A.
FROM GROUND OR ANOTHER COMBUSTIBLE SURFACE
11”
B.
FROM SIDE WALLS
6”
C.
FROM CEILING (MINIMUM)
36”
D.
ALCOVE WIDTH (MINIMUM
FIREPLACE LENGTH + 12”
E.
NON-COMBUSTIBLE BOARD ABOVE OPENING
8” MINIMUM
NOTE: SEE INSTALLATION MANUAL FOR ALL CLEARANCES AND REQUIREMENTS. TYPE-X NOT ALLOWED AS
NON-COMBUSTIBLE BOARD OVER APPLIANCE OPENING