flexbar 13290 User manual
Flexbar Wireless Inspection Camera
with Color LCD Monitor
MODEL NO. 13290
USER MANUAL
Please read this user manual carefully before using this
product!
CAUTIONS
• The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the apparatus.
• Turn off the Camera/Monitor if the system is not in use.
• The adapter is used as the disconnect device from the mains. The
adapter shall remain readily operable.
• The Camera/Monitor can only be completely disconnected from the
mains by unplugging the adapter.
• Do not cut the DC power cable of the apparatus to fit with another power
source.
• Attention should be drawn to the environment aspects of the battery
disposal.
• Remove the batteries when cleaning the unit.
• Remove the batteries before storing the unit for a long time.
• When necessary, REPLACE ALL FOUR BATTERIES in this unit with
new ones.
• Use only the size and type of battery with the correct polarity as indi-
cated in the battery compartment.
• Be sure to install the battery with the correct polarity as indicated in the
battery compartment.
• Properly dispose of the battery. Exposure to high temperatures can
cause the battery to explode, so do not dispose of in a fire. Place tape
over the terminals to prevent direct contact with other objects. Some
countries have regulations concerning battery disposal. Please follow all
applicable regulations.
250 Gibbs Road • Islandia, NY 11749
631-582-8440 • 800-879-7575
Email: sales@flexbar.com • www.flexbar.com
WELCOME
Thank you for choosing the Flexbar. Please read the User
Manual carefully before using this product.
The product is designed as a remote inspection device. It can
be used to look into tight spots and beam back real-time video
to the monitor. Typical applications might include HVAC in-
spection, automotive inspection, cable routing, automotive/
boat/aircraft inspection, etc.
PACKING LIST
2. Slide the ON/OFF switch to ON position and power indicator will light up
green, the picture display on LCD. Adjust the brightness, contrast, orienta-
tion, and roll the ON/OFF switch of the camera for better image effect.
3. When in use, the tube should easily maneuver itself into position going
forward.
TIP: The flexible tube can be bent into a certain shape. This may help you
explore the tube into narrow areas.
STRUCTURE
GENERAL SAFETY INFORMATION
WARNING! Read and understand all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
personal injury.
SAVE THESE INSTRUCTIONS!
* Prevent object and liquid entry. Never spill liquid of any kind on the
video display unit. Liquid increases the risk of electrical shock and damage
to the product.
* The unit is not shock-resistant. Do not use it as a hammer or drop it.
* Do not immerse the camera and monitor in water. Store in a dry
place. Such measures reduce the risk of electric shock and damage. The
imager head and the cable are water resistant when the unit is fully
assembled, but the monitor and camera is not.
* Do not use the camera if condensation forms inside the lens. Let
the water evaporate before using again.
Operation
1. Roll the ON/OFF switch to turn ON the camera, and the power indicator
will light. The switch then acts as a dimmer for the twin LEDs that sur-
round the camera on the imager head and provide lighting.
INSTALLATION
Please install the batteries, tube first before using the product.
Steps of installation as following:
To Install Batteries:
1. Using a screwdriver, remove screw and cover.
2. Remove battery compartment and insert four new AA batteries into the
proper slots in the battery compartment. Proper battery orientation is
indicated on the battery compartment.
3. Reinstall battery compartment and battery cover and screw as before.
NOTE! Dry your hands before installation or replacing batteries.
TO INSTALL CAMERA WITH FLEXIBLE TUBE
Connect the camera with tube to the body, make sure the keyed ends are
properly aligned. Once they are aligned, finger tighten the knurled knob to
hold the connection in place.
To Install Monitor for Wired Use
The product also supports wired use by connecting the monitor
to the camera.
To Connect Monitor Power
Plug the connect cable into power socket of monitor, and plug the end of
connect cable into adapter then connect the adapter to 8V~24V power, the
power indicator will lights on red, which indicates unit charging.
The built-in Li-battery will be charged after the adapter is plugged in, and
the Red indicator lights up during charging and will turn off after a full
charge.
