Fleximounts BR1D User manual

Item No. BR1D

01 02
Coach Screws Expansion Anchors Washer M5 Bolt
Te
Package Includes
chnical Specification
Tools Required for Assembly
Holdsup to
Weight Capacity
Dimensions
Colour
6 Bikes
90KG
1300mm x 280mm x 142mm
Black
Step 1-A: Install Support Brackets into Solid Concrete or Masonry Walls
Masonry / Concrete Wall
Support
Brackets
Mark the Mounting Holes
Power Drill
Drill holes with power drill at the
marked positions.
Washer
Support Brackets
Coach Screws
Align support brackets with holes, and install
coach screws as shown
Expansion Anchors
WALL
WALL
Note: Please completely screw in
the coach screwsand do not leave
any gap between support brackets
and wall to avoid risk of damage or
injury
Wall Plate
Wall Plate
60mm
Allen Key
Installation Steps
12
Determine your desired wall that you want to install
bike rack onto. Use a tape measure to determine
appropriate installation height and mark the mounting
holes with a pencil. Use a level if necessary.
Note: Ensure that all three support
brackets are mounted to the wall
Insert plastic expansion anchors into pre-drilled
holes and hammer in flush to wall.
3 4
x6 x6 x6
1 2 3
Hook x6 Square Tube x1
Support Bracket x3
Hammer
Ladder Eye Protection
Wood Drill Bit
Shifter Or Socket Wrench
Stud FinderTape Measure
Pencil Power Drill Masonry Drill Bit
Level

Step 2: Preassemble Square TubeStep 1-B: Install Support Brackets into Timber Wall Studs
Mark the Mounting Holes
Support Brackets
Wall Stud
Power Drill
2D
m
r
a
ill holes with power drill at the
rked positions.
WALL
WALL
Note: Please completely screw in
the coach screwsand do not leave
any gap between support brackets
and wall to avoid risk of damage or
injury.
Support Brackets
Washer
Coach Screws
3Align support bracketswith holes, and install coach screws as shown.
Wall Plate
Wall Plate
Square Tube
Support Bracket
Note: Do not release the square tube during installation
to prevent it from falling off and hurting people.
Step 3: Install Hooks
60mm
03 04
Determine your desired wall that you want to install bike
rack onto. Use a tape measure to determine appropriate
installation height and mark the mounting holes with a
pencil. Use a level if necessary.
Note: Ensure that all three support
brackets are mounted to the wall.
Pass the square tube through the left support bracket first, feeding through middle and then finally right
hand support bracket.
Insert all hooks from the right end of the square tube in order.
Note: Do not release the square tube during installation
to prevent it from falling off and hurting people.
Hook
1

Step 4: Install Limit Screws To Complete Installation
Step 5: Hang Your Bikes
05 06
Bolt M5 Allen Key
E
D
Square Tube
●This product contains small items that could be a choking hazard if swallowed. Ensure that
these items are kept well away from children at all times.
● Ensure that the enclosed installation manual is thoroughly read and completely understood
before undertaking installation. If you are unsure nor confident about installing this product
based on the information provided in the installation manual, please contact a qualified
tradesperson for assistance.
● Good quality tools and safety equipment are highly recommended when installing this product.
● Prior to installation, confirm that the weight capacity of the wall substrate you are intending to
install shelving onto can support the maximum load rating of this product or multiple products.
●All fixing points available on support brackets must be utilised, ensuring all screws are firmly
tightened into the wall’s substrate post installation.
● Check joint parts on each installed unit every three months, making sure that any screws in
particular have not come loose.
● Never exceed the 90kg maximum load rating for this product, over loading product beyond the
load rating could lead to product damage or physical injury.
●This product is intended for indoor use only. Use of this product outdoors could lead to product
damage or physical injury.
● Do not install onto metal stud wall frames under any circumstances
Note：When storing more than three bikes the most
economical way is to top and tail your bikes Eg first
bike handles bars up, second bike handles bars down.
Ensure that the limit screws holes on the square tube are positioned either side of the left support
bracket. Use the Allen key (E) provided to screw bolts (D) into the square tube to complete bike
rack assembly.