Kogan KAWLM55CNRA User manual

TILT EXTENDABLE FULL MOTION
CORNER WALL MOUNT
(23" - 55")
KAWLM55CNRA

•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and quality tools must be used.
•This product is suitable for installation on solid concrete walls, masonry walls or
wood stud walls.
•Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
•Use the mounting screws provided and DO NOT OVER TIGHTEN mounting
screws.
•Do not allow children to play near this stand.
•This product contains small items that could be a choking hazard if swallowed.
Keep these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead
to product failure and personal injury.
•A minimum of two people are recommended for this installation. Failure to use
safety gear and safe working methods may result in property damage, serious
injury or death.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
VESA compatibility:
200x100, 200x200, 300x300, 400x200, 400x300, 400x400
CAUTION:
Rated weight is 45kg (99 lbs).
Use with products heavier than the rated weights indicated may result
in instability causing possible injury.
Suitable for TVs 23” – 55” maximum
SAFETY & WARNINGS

Wall mount assembly:
A(x1)
B(x1)
C(x2)
D(x2)
EM6 (x3)
F(x8)
G(x1)
W-A ST6.3x55 (x8)
W-B Ø10x45 (x8)
W-C (x8)
Adapters (depends on TV):
M-A M5x14 (x4)
M-B M6x14 (x4)
M-C M6x30 (x4)
M-D M8x30 (x4)
M-E M8x50 (x4)
M-F D6 (x4)
M-G D8 (x4)
M-H (x8)
M-I (x8)
COMPONENTS

Additional Tools Required (Not Supplied):
Phllips head
screwdriver
Stud finder
Spirit level
Pencil
Electric drill
Socket wrench
Step 1: Drywall, plaster or timber walls (with studs)
Use a stud finder to locate safe and suitable locations to install into wall. Use a spirit level to
double check the correct angle of the mount and mark the intended hole positions with a
pencil. Drill holes in the desired locations (55mm deep, 4.5mm wide).
With the wall mount held in place, insert
the washers and screws (W-C, W-A),
tightening with a socket wrench. When
installing on a drywall, plaster or timber
wall, do not use the screw anchors (W-B).
ASSEMBLY

Step 1: Concrete and masonry walls
Use a spirit level to double check the correct angle of the mount and mark the intended hole
positions with a pencil. Drill holes in the desired locations (60mm deep, 10mm wide).
Insert the screw anchors (W-B) into each pre-drilled hole. With the wall mount held in place,
insert the washers and screws (W-C, W-A), tightening with a socket wrench.
For all wall types:
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in
property damage, serious injury, or death.
Ensure washers and screws are aligned in the
centre of opening. Do not install with washers and
screws off to either side.

Step 2: Preparing the VESA mount plate
Ensure the two top nuts (E) are not fully tightened, leaving a gap of 4mm.
Configuration for VESA 300x300, 400x400:

400x200:
400x300:

Step 3: Attaching the mounting brackets to your TV.
Depending on your TV, a combination of spacers (M-G, M-H) may be required to help create
the correct amount of space for the brackets. Ensure the screws are fitted correctly into your
TV’s VESA mount holes, and are not too long or too short in the back of the TV.

Step 4: Attaching the TV to the wall mount.
With two people, lift the TV up and into position on the mount, ensuring the 4mm gaps on
the mount plate nuts slide into the two openings on the mount.
The lower bolt of the mount plate should feed through the opening at the bottom of the
mount. Secure this with a nut (E), while tightening the two top nuts.
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in
property damage, serious injury, or death.