FLIR Raymarine Raymic Series User manual

RaymafHH
Raymic 60/70 Handset installation
instructions
Powering on the handset
The Raymic 60/70 handset accessory can be connected to the
Ray60 and Ray70 radios.
The Handset must be switched on using the Handset's Power
button.
With the Handset connected to the Base station:
7. OK / menu button - Press button to access menu / DSC
functions and to confirm selections.
8. 16 / PLUS - When powered on press to switch between
priority channels.
9. HI/LO - Press to switch between High (25 W)and low (1
W) transmit power.
10. DISTRESS - Lift up the spring loaded cover and press this
button to make a DSC distress call.
1 1 . Channel Up and Down - Changes the channel up or down.
12. VOL/SQ - Press button to switch between volume and
squelch control.
13. Built-in speaker
Second handset station - Ray60 /
Ray70
The Raymic handset accessory can be connected to the second
station connector located on the rear of the radio, this will create
a second fully functional station.
1. Primary station.
2. Raymic handset extension cable (480290, A80291 or
480292)
3. Raymic handset second station (480289)
4. Panel mount fixings kit (R70438)
5. Raymic handset adaptor cable with RCA audio (480297)
6. Primary station passive speaker
7. Second station passive speaker
Note: As the Fistmic does not include a display it cannot be
used to create a second functional station.
Alarm behavior for second station passive
speakers
The 480297 adaptor cable can be used on the Ray60 and Ray70
Radios to connect an additional passive speaker to the second
station. A passive speaker connected to the second station will
only receive voice audio. Alarms will NOT be heard from the
passive speaker when it is connected to the second station.
Handset extension cables
Handset station cabling can be extended using approved
extension cables.
The maximum length of cable from the Handset to the Base
station should not exceed 50 m (164 ft)
2.
1. Press the Power button.
The Handset will switch on.
To switch the Handset off, press and hold the Power button
for approximately 3 seconds.
Ray60 / Ray70 handset controls
The optional handset for the Ray60 and Ray70 VHF radios
includes the following controls:
1. Power - Press to power the handset on. Press and hold
for 3 seconds to power the handset off. Momentary press to
access the shortcut list.
2. PTT (Push to Talk) - Press and hold to send a voice
message. Release to return to receive mode"
Note: The maximum transmit time is limited to 5 minutes
to prevent un-intentional transmissions from occupying
the VHF channel.
3. Microphone location
4. Volume Up and Down - Press to adjust volume or squelch
up and down.
5. LCD
6. Back - Move back through menu options.
Document number: 88064-'l
llLatUE+l--o
l'[sl. I
lFl=l=?- | u;;r
fii--:l::-llJ
\i\ =l: ,r/ v
\\\t-t--r7
\l=t.-/ 6)
v
(,
Date:03-2016

Ray60 / Ray70 Raymic handset cradle
mounting
Before mounting the unit, ensure that you have:
Selected a suitable location, ensuring there is nothing behind
the mounting sudace that may be damaged when drilling.
ldentified the cable connections and route that the cables will
take.
1. Check the selected location for the mounting clip, a clear flat
area is required, with sufficient space around it to place and
remove the Handset.
Using a pencil, offer up the cradle to the desired location and
mark the location of the screw holes on the mounting surface.
Drill the mounting holes using a suitable size drill bit.
Hold the cradle in place and secure using the screws provided
Place the Handset into the cradle until it clicks into position.
o13303 I
1. Check the selected location for the Mounting plate, a clear flat
area is required.
2. Using a pencil, offer up the Mounting plate to the desired
location and mark the location of the screw holes and the
center hole on the mounting panel.
3. Drill the mounting holes using a suitable size drill bit.
4. Drill the center hole using a 25 mm (1 in.) hole cutting saw.
5. Pull the connector end of the cable through the hole in the
mounting surface.
6. Place the Mounting plate gasket over the end of the connector.
7. With the recessed side facing away from the mouniing panel,
place the Mounting plate over the end of the connector.
8. Place the lanyard end of the Splash-proof dust cap over
the connector, ensuring the lanyard sits in the recess in the
Mounting plate.
9. Place the Mounting plate nut over the connector and tighten
clockwise using a 13/16 in. (21 mm) socket wrench, being
careful not to damage the plastic nut by ovedightening.
10. Secure the Mounting plate to the mounting surface using the
supplied screws.
11 . Attach the Handset / Fistmic connector to the cable connector
and rotate the locking collar clockwise to secure.
'12.Connect the opposite end of the cable to the required
connector either on the Base station or to another
pass-through panel mounting plate connector.
Note: Drill bit, tap size and tightening torque is dependent on
the thickness and type of material the unit is to be mounted on.
2.
J.
4.
5.
Pass-through panel kit mounting
When installing the Fistmic or the optional Raymic handset, the
pass-through panel kit should be used to secure the cable to any
panels the cable has to pass through.
1Splash-proof dust cap with lanyard
2Mounting plate fixings x 3
3Mounting plate nut
4Mounting plate
5Mounting plate gasket
oExtension cable
Raymic 60/70 Handset installation instructions