Fluidwell F Series User manual

F016-P
FLOW RATE INDICATOR / TOTALIZER
WITH LINEARIZATION AND SCALED PULSE OUTPUT
Signal input flowmeter: pulse, Namur and coil
Output: one scaled pulse ref. accumulated total
Options: Intrinsically Safe
F-Series - Field mounted indicators for safe and hazardous areas.
More info: www.fluidwell.com/fseries

Page 2
FW-F016-P-M_v0404_01_EN.docx
SAFETY INSTRUCTIONS
•Any responsibility is lapsed if the instructions and procedures as described in this manual
are not followed.
•LIFE SUPPORT APPLICATIONS: The F016-P is not designed for use in life support
appliances, devices, or systems where malfunction of the product can reasonably be
expected to result in a personal injury. Customers using or selling these products for use
in such applications do so at their own risk and agree to fully indemnify the manufacturer
and supplier for any damages resulting from such improper use or sale.
•Electro static discharge does inflict irreparable damage to electronics! Before installing or
opening the F016-P, the installer has to discharge himself by touching a well-grounded
object.
•The F016-P must be installed in accordance with the EMC guidelines (Electro Magnetic
Compatibility).
•Connect a proper grounding to the metal enclosure as indicated if the F016-P has an
incoming power or signal line which carries a hazardous live voltage.
The Protective Earth (PE) wire may never be disconnected or removed.
•Intrinsically Safe applications: follow the instructions as mentioned in Chapter 5.
Certificates and related documents are available on our website or from your distributor.
DISPOSAL OF ELECTRONIC WASTE
•The WEEE Directive requires the recycling of disposed electrical and electronic
equipment in the European Union. When the WEEE Directive does not apply to your
region, we support its policy and ask you to be aware on how to dispose of this product.
•The crossed out wheelie bin symbol as illustrated and found on our products tells that this
product shall not be disposed of into the general waste system or into a landfill.
•At the end of its life, equipment shall be disposed of according to the local regulations
regarding waste of the electrical and the electronic equipment.
• Technical
helpdesk for information on the product disposal.
SAFETY RULES AND PRECAUTIONARY MEASURES
•The manufacturer accepts no responsibility whatsoever if the following safety rules and
precautions, instructions and the procedures as described in this manual are not
followed.
•Modifications of the F016-P implemented without preceding written consent from the
manufacturer, will result in the immediate termination of product liability and warranty
period.
•Mounting, electrical installation, start-up and maintenance of this device may only be
carried out by trained persons authorized by the operator of the facility. Persons must
read and understand this manual before carrying out its instructions.
•This device may only be operated by persons who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Check the mains voltage and information on the manufacturer's plate before installing the
F016-P.
•Check all connections, settings and technical specifications of the various peripheral
devices with the F016-P supplied.
•Open the enclosure only if all leads are free of potential.
•Never touch the electronic components (ESD sensitivity).
•Never expose the system to heavier conditions than allowed according to the
classification of the enclosure (see manufacture's plate and chapter 4.2.).
•If the operator detects errors or dangers, or disagrees with the safety precautions taken,
he should inform the owner or principal responsible.
•The local labor and safety laws and regulations must be adhered to.

Page 3
FW-F016-P-M_v0404_01_EN.docx
ABOUT THE MANUAL
This operation manual is divided into two main sections:
•The daily use of the F016-
meant for users.
•The following chapters and appendices are exclusively meant for electricians/technicians. These
provide a detailed description of all software settings and hardware installation guidance.
This operation manual describes the standard F016-P as well as most of the options available. For
additional information, please contact your supplier.
A hazardous situation may occur if the F016-P is not used for the purpose it was designed for
or is used incorrectly. Please carefully note the information in this operating manual
indicated by the pictograms:
A "warning !" indicates actions or procedures which, if not performed correctly, may lead to
personal injury, a safety hazard or damage of the F016-P or connected instruments.
A "caution !" indicates actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect functioning of the F016-P or connected instruments.
A "note !" indicates actions or procedures which, if not performed correctly, may indirectly
affect operation or may lead to an instrument response which is not planned.
WARRANTY AND TECHNICAL SUPPORT
For warranty and technical support for your Fluidwell products,
visit our internet site www.fluidwell.com or contact us at s[email protected]om.
Hardware version : 03.03.xx
Software version : 03.03.xx
Manual : FW-F016-P-M_v0404_01_EN.docx
© Copyright 2022 : Fluidwell B.V. - the Netherlands
Information in this manual is subject to change without prior notice. The
manufacturer is not responsible for mistakes in this material or for incidental
damage caused as a direct or indirect result of the delivery, performance or
use of this material.
© All rights reserved. No parts of this publication may be reproduced or used
in any form or by any means without written permission of your supplier.

Page 4
FW-F016-P-M_v0404_01_EN.docx
CONTENTS MANUAL
SAFETY INSTRUCTIONS.................................................................................................................... 2
DISPOSAL OF ELECTRONIC WASTE............................................................................................... 2
SAFETY RULES AND PRECAUTIONARY MEASURES ................................................................... 2
ABOUT THE MANUAL ........................................................................................................................ 3
WARRANTY AND TECHNICAL SUPPORT........................................................................................ 3
CONTENTS MANUAL ......................................................................................................................... 4
1INTRODUCTION ..................................................................................................................... 6
1.1 System description of the F016-P............................................................................................6
2OPERATIONAL....................................................................................................................... 7
2.1 General information .................................................................................................................7
2.2 Control panel............................................................................................................................7
2.3 Operator information and functions .........................................................................................7
3CONFIGURATION................................................................................................................... 9
3.1 Introduction ..............................................................................................................................9
3.2 Programming SETUP-level......................................................................................................9
3.2.1 Entering SETUP-level..............................................................................................................9
3.2.2 Navigating through SETUP-level.............................................................................................9
3.2.3 Programming sequence.........................................................................................................10
3.2.4 Returning to OPERATOR-level .............................................................................................11
3.3 Configuration Settings............................................................................................................12
3.3.1 Overview functions SETUP level...........................................................................................12
3.3.2 Explanation of SETUP-menu 1 - Total...................................................................................13
3.3.3 Explanation of SETUP-menu 2 - Flow rate............................................................................13
3.3.4 Explanation of SETUP-menu 3 - Display...............................................................................14
3.3.5 Explanation of SETUP-menu 4 - Power management..........................................................15
3.3.6 Explanation of SETUP-menu 5 - Flowmeter..........................................................................15
3.3.7 Explanation of SETUP-menu 6 - Linearization......................................................................16
3.3.8 Explanation of SETUP-menu 7 - Pulse output ......................................................................17
3.3.9 Explanation of SETUP-menu 8 - Others................................................................................17
4INSTALLATION..................................................................................................................... 18
4.1 General directions..................................................................................................................18
4.2 Installation / surrounding conditions ......................................................................................18
4.3 Handling the F-Series enclosure ...........................................................................................19
4.3.1 Identification...........................................................................................................................19
4.3.2 Opening / Removing the cover ..............................................................................................21
4.3.3 Closing / Replacing the cover................................................................................................21
4.4 Mechanical installation...........................................................................................................22
4.4.1 Dimensions Aluminum and stainless steel enclosures.......................................................22
4.4.2 Dimensions Non-metallic enclosures..................................................................................23
4.4.3 Mounting ................................................................................................................................24
4.5 Electrical installation ..............................................................................................................25
4.5.1 Electrical safety......................................................................................................................25
4.5.2 Protective Earth (PE) connections.........................................................................................25
4.5.3 Field wiring connections.........................................................................................................26
4.5.4 Power supply wiring...............................................................................................................27
4.5.5 Sensor supply ........................................................................................................................27
4.6 Terminal connectors safe area applications Type PB / PX / PD ........................................28
4.6.1 Terminals 1-3: Flowmeter input .............................................................................................28
4.6.2 Terminal 4-5: Power supply - type PX (default) and PD (option) ..........................................30
4.6.3 Terminal 6: Power supply type PD: 8.2V sensor supply........................................................30
4.6.4 Terminal 7-8: Pulse output Type OT...................................................................................31
4.6.5 Terminal 9-10: Power supply backlight - type ZB (option).....................................................31
4.7 Terminal connectors safe area applications Type PF / PM................................................32
4.7.1 Terminal GND-1-2: Power Supply .........................................................................................32
4.7.2 Terminal 3-4: Pulse output.....................................................................................................32
4.7.3 Terminals 5-7: Flowmeter input .............................................................................................33
5INTRINSICALLY SAFE APPLICATIONS............................................................................. 36
5.1 Identification...........................................................................................................................36
5.2 Electrical installation in hazardous area ................................................................................37

Page 5
FW-F016-P-M_v0404_01_EN.docx
5.2.1 General information and instructions..................................................................................... 37
5.2.2 Installations based on FM or CSA certificate ........................................................................ 37
5.2.3 Electrical data - Control drawing ........................................................................................... 38
5.2.4 Installations based on ATEX or IECEx certificate ................................................................. 39
5.2.5 Electrical data Annex 1....................................................................................................... 40
5.2.6 Power supply wiring............................................................................................................... 41
5.2.7 Sensor supply........................................................................................................................ 41
5.3 Terminal connectors Intrinsically Safe applications .............................................................. 42
5.4 Configuration examples Intrinsically Safe applications ......................................................... 42
5.4.1 F016-P-(OT)-PC-(PX)-XI-(ZB) Battery powered - Ex ia IIC/IIIC............................................ 42
5.4.2 F016-P-OT-PX-XI-ZB - Ex ia IIC/IIIC..................................................................................... 43
5.4.3 F016-P-OT-PX-XI-(ZB) - Ex ia IIc/IIIC................................................................................... 43
5.4.4 F016-P-OT-PD-XI-ZB - Ex ia IIc/IIIC ..................................................................................... 44
6MAINTENANCE.....................................................................................................................45
6.1 General directions ................................................................................................................. 45
6.2 Instructions for repair............................................................................................................. 45
6.3 Battery replacement .............................................................................................................. 46
6.3.1 Safety instructions ................................................................................................................. 46
6.3.2 Replace the battery ............................................................................................................... 47
6.3.3 Disposal of batteries.............................................................................................................. 47
TECHNICAL SPECIFICATION.................................................................................48
PROBLEM SOLVING ...............................................................................................51
DECLARATION OF CONFORMITY .........................................................................52
INDEX OF THIS MANUAL..................................................................................................................53
LIST OF FIGURES..............................................................................................................................54

Page 6
FW-F016-P-M_v0404_01_EN.docx
1 INTRODUCTION
1.1 SYSTEM DESCRIPTION OF THE F016-P
Functions and features
The flow rate / totalizer model F016-P is a microprocessor driven instrument designed to linearize
the flowmeters flow curve and display flow rate, total and accumulated total as well as to generate a
scaled pulse according the accumulated total.
This product has been designed with a focus on:
•ultra-low power consumption to allow long-life battery powered applications
(type PB / PC);
•intrinsic safety for use in hazardous applications (type XI);
•several mounting possibilities with GRP, aluminum or stainless steel 316L enclosures for
industrial surroundings,
•ability to process all types of flowmeter signals;
•transmitting possibilities with one configurable output.
Flowmeter input
This manual describes the F016-P with a pulse type input from the flowmeter "-P version". Other
versions are available to process (0)4-20mA or 0-10V flowmeter signals.
One flowmeter with a passive or active pulse, Namur or coil signal output can be connected to the
F016-P. To power the sensor, several options are available.
Fig. 1: Typical application for the F016-P.
Configuration of the F016-P
The F016-P has been designed to be implemented in many types of applications. For that reason, a
SETUP-level is available to configure your F016-P according to your specific requirements.
It includes several important features, such as K-Factor, measurement units, signal selection etc. All
setting are stored in EEPROM memory and will not be lost in the event of power failure. To extend
the battery-life time, please use of the power-management functions as described in chapter 3.3.2.
Display information
The F016-P has a large transflective LCD with all kinds of symbols and digits to display measuring
units, status information, trend-indication and key-word messages.
Flow rate and totals can be displayed either with the small 8mm digits or with the 17mm digits.
A backup of the total and accumulated total in EEPROM memory is made every minute.
Options
The following options are available: intrinsic safety, mechanical relay or active outputs, power- and
sensor-supply options, panel-mount, wall-mount and weather-proof enclosures, flame proof
enclosure and LED backlight.
Overview typical application F016
pulse output
LINEARISATION

Page 7
FW-F016-P-M_v0404_01_EN.docx
2 OPERATIONAL
2.1 GENERAL INFORMATION
This chapter describes the daily use of the F016-P. This instruction is meant for users / operators.
•The F016-P may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed
•Take careful notice of the "Safety rules, instructions and precautionary measures" in the
front of this manual.
2.2 CONTROL PANEL
The control panel has three keys. The following keys are available:
Fig. 2: Control panel.
Functions of the keys
PROG-key
This key is used to program and save new values or settings.
The PROG-key is also used to gain access to SETUP-level; please read chapter 3.
SELECT-key
This key is used to SELECT the displayed information, like accumulated total and flow
rate.
CLEAR-key
This key is used to CLEAR the value of total.
2.3 OPERATOR INFORMATION AND FUNCTIONS
In general, the F016-P will always function at Operator level. The information displayed is dependent
upon the SETUP-settings. The signal from the connected sensor is processed by the F016-P in the
background, whichever screen refresh rate setting is chosen. After pressing a key, the display will be
updated very quickly during a 30 second period, after which it will slow-down again.
Fig. 3: Example of display information during process.
For the Operator, the following functions are available:
•Display flow rate / total or Flow rate
This is the main display information of the F016-P. After selecting any other information, it will
always return to this main display automatically.
Total is displayed on the upper-line of the display and flow rate on the bottom line.
It is possible to display flow rate only with the large 17mm digits; in this instance press the
SELECT-key to read the total.
When "-------" is shown, then the flow rate value is too high to be displayed. The arrows 
indicate the increase/decrease of the flow rate trend.
RUN

Page 8
FW-F016-P-M_v0404_01_EN.docx
•Clear total
The value for total can be re-initialized. To do so, press CLEAR twice. After pressing CLEAR
once, the flashing text "PUSH CLEAR" is displayed. To avoid re-initialization at this stage, press
another key than CLEAR or wait for 20 seconds.
Re-initialization of total DOES NOT influence the accumulated total.
•Display accumulated total
When the SELECT-key is pressed, total and accumulated total are displayed. The accumulated
total cannot be re-initialized. The value will count up to 99,999,999,999. The unit and number of
decimals are displayed according to the configuration settings for total.
•Low-battery alarm
When the battery voltage drops, it must be replaced. At first "low-battery" will flash, but as soon
as it is displayed continuously, the battery MUST be replaced shortly after!
The remaining lifetime after the first moment of indication is generally several days up to some
weeks. See paragraph 6.3 for further information on battery replacement.
Fig. 4: Example of low-battery alarm.
•Alarm 01-03
When "alarm" is displayed, please consult Appendix B: problem solving.

Page 9
FW-F016-P-M_v0404_01_EN.docx
3 CONFIGURATION
3.1 INTRODUCTION
This and the following chapters are exclusively meant for electricians and non-operators. In these,
an extensive description of all software settings and hardware connections are provided.
•Mounting, electrical installation, start-up and maintenance of the instrument may only be
carried out by trained personnel authorized by the operator of the facility. Personnel must
read and understand this Operating Manual before carrying out its instructions.
•The F016-P may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Ensure that the measuring system is correctly wired up according to the wiring diagrams.
The housing may only be opened by trained personnel.
•Take careful notice of the "Safety rules, instructions and precautionary measures" in the
front of this manual.
3.2 PROGRAMMING SETUP-LEVEL
Changing the settings of the F016-P may have an influence on the current operation of the
device, even when SETUP-level is still active.
Make sure that the unit is not being used for any application when altering the settings.
3.2.1 ENTERING SETUP-LEVEL
Configuration of the F016-P is done at SETUP-level, which can be reached at all times while the
F016-P remains fully operational. At SETUP-level the display will deactivate the RUN indicator and
activate the SETUP indicator.
Use the control panel to access SETUP-level
PROG-key
To enter SETUP-level, press the PROG-key for 7 seconds at OPERATOR-level.
During this time, the symbols  will be displayed.
When SETUP-level is entered, a password might be required to continue. You can
enter the password by following the procedure for programming values as described in
the following paragraphs.
A password may be required to enter SETUP.
Without this password access to SETUP is denied.
3.2.2 NAVIGATING THROUGH SETUP-LEVEL
Each function has a unique menu-number, which is displayed near the SETUP indicator at the
bottom of the display. The menu-number is a combination of two figures, e.g. 1.2. The first number
indicates the function-group and the second number indicates the function. Additionally, each
function and function-group is expressed with a keyword.
Fig. 5: SETUP matrix structure
1.1
1.2
2.1.
2.1
1.3
2.2
3.1
3.
FUNCTION GROUP
FUNCTION
FW-4100-000001-001-EN

Page 10
FW-F016-P-M_v0404_01_EN.docx
Use the control panel to navigate through SETUP-level
PROG-key
When a function is selected, this key is used to start the programming sequence.
When only a function group is selected (and no function), this key is used to scroll back
a function group (e.g. 3 →2 →1 →3).
SELECT-key
This key is used to select the next function in the list (e.g. 1 →1.1 →1.2 →1). When
the top of the list is reached, it will wrap around and return to the function group
selection.
CLEAR-key
This key is used to select the previous function in the list (e.g. 1.2 →1.1 →1 →2).
When the bottom of the list is reached, it will return to the function group selection.
When only a function group is selected (and no function), this key is used to scroll to
the next function group. (e.g. 1 →2 →3 →1).
3.2.3 PROGRAMMING SEQUENCE
After selecting a function at SETUP-level, a new value can be programmed using the control panel.
A function either contains a value (a number with optionally a decimal point, e.g. 123.45) or a list
with items (e.g. Disable Enable).
For each function that needs to change, navigate to that function and follow the steps indicated
below. During the programming sequence, the display will deactivate the SETUP indicator and
activate the PROGRAM indicator.
When programming new values, alterations will only be set after the PROG-key has been
pressed to confirm the new value! (STEP 3)
Step 1: Starting the programming sequence
PROG-key
When a function is selected at SETUP-level, this key is used to start the programming
sequence.
Step 2a: Changing a value
SELECT-key
This key is used to increment the selected digit.
When the entered value is out of range, the increase sign or decrease-sign will
be displayed while you are programming. If this value is confirmed by pressing the
PROG-key, the value will be brought within a valid range automatically.
CLEAR-key
This key is used to select the next digit. If a decimal point can be set, this will be
included in the sequence as well (e.g. [decimal point] →digit 1 →digit 2→digit 3 →
[decimal point].
SELECT-key + CLEAR-key
The combination of the SELECT-key and CLEAR-key is used to select a negative
value. When a value can also be entered as a negative number, pressing the SELECT-
key and CLEAR-

Page 11
FW-F016-P-M_v0404_01_EN.docx
Step 2b: Changing the selected item in a list
SELECT-key
This key is used to select the next item in the list (e.g. Disable →Enable).
At the end of the list, the selection will wrap around to the first selection.
CLEAR-key
This key is used to select the previous item in the list (e.g. Enable →Disable ).
At the bottom of the list, the selection will wrap around to the last selection.
Step 3: Finishing the programming sequence
PROG-key
During the programming sequence, this key is used to confirm the new value and
return to SETUP-level. To cancel the operation, either press the PROG-key for 3
seconds or wait for 20 seconds: the programming sequence is cancelled and the
former value is reinstated.
3.2.4 RETURNING TO OPERATOR-LEVEL
When all settings are configured correctly, the unit can be returned to OPERATE-level.
Please keep a record of all settings for later reference.
Use the control panel to return to OPERATE-level
PROG-key
In order to return to the operator level, press the PROG-key for three seconds.
When no keys are pressed for 2 minutes, SETUP-level will be left automatically.

Page 12
FW-F016-P-M_v0404_01_EN.docx
3.3 CONFIGURATION SETTINGS
All settings of the F016-P can be set via the control panel.
The following paragraphs give a detailed description of each setting.
3.3.1 OVERVIEW FUNCTIONS SETUP LEVEL
SETUP FUNCTIONS AND VARIABLES
1
TOTAL
1.1
UNIT
L - m3 - kg - lb - GAL - USGAL - bbl - no unit
1.2
DECIMALS
0 - 1 - 2 - 3 (Ref: displayed value)
1.3
K-FACTOR
0.000010 - 9,999,999
1.4
DECIMALS K-FACTOR
0 - 6
2
FLOW RATE
2.1
UNIT
mL - L - m3 - mg - g - kg - ton - GAL - bbl - lb - cf - REV - no unit - scf -
Nm3 - NL - P
2.2
TIME UNIT
sec - min - hour - day
2.3
DECIMALS
0 - 1 - 2 - 3 (Ref: displayed value)
2.4
K-FACTOR
0.000010 - 9,999,999
2.5
DECIMALS K-FACTOR
0 - 6
2.6
CALCULATION
per 1 - 255 pulses
2.7
CUT-OFF
0.1 - 999.9 seconds
3
DISPLAY
3.1
FUNCTION
total - flow rate
3.2
BACKLIGHT (optional)
off - on
3.3
BL. BRIGHTNESS (optional)
1 - 5
4
POWER MANAGEMENT
4.1
LCD NEW
fast - 1 sec - 3 sec - 15 sec - 30 sec - off
4.2
BATTERY MODE
operational - shelf
5
FLOWMETER
5.1
SIGNAL
npn - npn_lp - reed - reed_lp - pnp - pnp_lp - namur - coil_hi - coil_lo -
active
6
LINEARIZATION
6.1
FREQ. / M-FACTOR 1
0.1 –9,999.9 Hz / 0.000001 –9.999999
6.2
FREQ. / M-FACTOR 2
0.1 –9,999.9 Hz / 0.000001 –9.999999
...
..
……..
6.8
FREQ. / M-FACTOR 8
0.1 –9,999.9 Hz / 0.000001 –9.999999
6.9
LINEARISATION
enable / disable
6.A
DECIMALS FREQUENCY
00000 - 1111.1 -222.22 - 33.333
7
PULSE OUTPUT
7.1
PULSE WIDTH
0.001 - 9.999 sec
7.2
DECIMALS
0 - 1 - 2 - 3
7.3
IMPULSE PER
X-quantity
8
OTHERS
8.1
TYPE / MODEL
F016-P
8.2
SOFTWARE VERSION
03.xx.xx
8.3
SERIAL NO.
xxxxxxx
8.4
PASS CODE
0000 - 9999
8.5
TAGNUMBER
0000000 - 9999999

Page 13
FW-F016-P-M_v0404_01_EN.docx
3.3.2 EXPLANATION OF SETUP-MENU 1 - TOTAL
SETUP FUNCTIONS AND VARIABLES
1
TOTAL
1.1
UNIT
This setting determines the measurement unit for total and
accumulated total.
The following units can be selected:
L - m3 - kg - lb. - GAL - USGAL - bbl - ---- (no unit).
Alteration of the measurement unit will have consequences for
operator and SETUP-level values.
Please note that the K-factor has to be adapted as well; the
calculation is not done automatically.
1.2
DECIMALS
The decimal point determines for total and accumulated total the
number of digits following the decimal point.
The following can be selected:
0000000 - 111111.1 - 22222.22 - 3333.333
1.3
K-FACTOR:
With the K-factor, the flowmeter pulse signals are converted to a
quantity. The K-factor is based on the number of pulses generated by
the flowmeter per selected measurement unit (SETUP 1.1), for
example per cubic meter. The more accurate the K-factor, the more
accurate the functioning of the system will be.
Example 1: Calculating the K-factor.
Let us assume that the flowmeter generates 2.4813 pulses per liter
and the selected unit is "cubic meters / m3". A cubic meter consists of
1000 parts of one liter which implies 2,481.3 pulses per m3. So, the
K-factor is 2,481.3. Enter for SETUP 1.3: "2481300" and for
SETUP 1.4 - decimals K-factor "3".
Example 2: Calculating the K-factor.
Let us assume that the flowmeter generates 6.5231 pulses per gallon
and the selected measurement unit is gallons. So, the K-Factor is
6.5231. Enter for SETUP 1.3: "6523100" and for SETUP 1.4 decimals
K-factor "6".
1.4
DECIMALS K-FACTOR
This setting determines the number of decimals for the K-factor
entered (SETUP 1.3). The following can be selected:
0 - 1 - 2 - 3 - 4 - 5 - 6
Please note that this setting influences the accuracy of the K-factor
indirectly (i.e. the position of the decimal point and thus the value
given).
This setting has NO influence on the displayed number of digits for
total (SETUP 1.2)!
3.3.3 EXPLANATION OF SETUP-MENU 2 - FLOW RATE
The settings for total and flow rate are entirely separate. In this way, different units of measurement
can be used for each e.g. cubic meters for total and liters for flow rate.
The display update time for flow rate is one second or more.
SETUP FUNCTIONS AND VARIABLES
2
FLOW RATE
2.1
UNIT
SETUP 2.1 determines the measurement unit for flow rate.
The following units can be selected:
mL - L - m3 - mg - g - kg - ton - GAL - bbl - lb - cf - REV - ---- (no unit)
- scf - Nm3 - NL - P.
Alteration of the measurement unit will have consequences for
operator and SETUP-level values.
Please note that the K-factor has to be adapted as well; the
calculation is not done automatically.
2.2
TIME UNIT
The flow rate can be calculated per second (SEC), minute (MIN), hour
(HR) or day (DAY).

Page 14
FW-F016-P-M_v0404_01_EN.docx
2.3
DECIMALS
This setting determines for flow rate the number of digits following the
decimal point.
The following can be selected:
00000 - 1111.1 - 2222.22 - 3333.333
2.4
K-FACTOR
With the K-factor, the flowmeter pulse signals are converted to a flow
rate.
The K-factor is based on the number of pulses generated by the
flowmeter per selected measurement unit (SETUP 2.1), for example
per liter. The more accurate the K-factor, the more accurate the
functioning of the system will be. For examples read SETUP 1.3.
2.5
DECIMALS K-FACTOR
This setting determines the number of decimals for the K-factor
(SETUP 2.4).
The following can be selected:
0 - 1 - 2 - 3 - 4 - 5 - 6
Please note that this SETUP - influences the accuracy of the K-factor
indirectly.
This setting has NO influence on the displayed number of digits for
"flow rate" (SETUP 2.3)!
2.6
CALCULATION
The flow rate is calculated by measuring the time between a number
of pulses, for example 10 pulses. The more pulses the more accurate
the flow rate will be. The maximum value is 255 pulses.
•The lower the number of pulses, the higher the power consumption
of the F016-P will be (important for battery powered applications).
•For low frequency applications (below 10Hz): do not program more
than 10 pulses else the update time will be very slow.
•For high frequency application (above 1kHz) do program a value of
100 or more pulses.
2.7
CUT-OFF
With this setting, you determine a minimum flow requirement thresh-
hold, if during this time less than XXX-pulses (SETUP 2.6) are
generated, the flow rate will be displayed as zero.
The cut-off time has to be entered in seconds - maximum time is 999
seconds (about 15 minutes).
3.3.4 EXPLANATION OF SETUP-MENU 3 - DISPLAY
SETUP FUNCTIONS AND VARIABLES
3
DISPLAY
3.1
FUNCTION
The large 17mm digits can be set to display total or flow rate.
When "total" is selected, both total and flow rate are displayed
simultaneously.
When "flow rate" is selected, only flow rate will be displayed with its
measuring unit while total will be displayed after pressing SELECT.
The functions below will only effect the optional LED-backlight.
3.2
BACKLIGHT (optional)
If a LED backlight has been supplied, it can be turned on or off.
3.3
BL. BRIGHTNESS
(optional)
The backlight brightness is adjustable. The following can be selected:
1 5 (where 1 is minimum and 5 is maximum brightness)

Page 15
FW-F016-P-M_v0404_01_EN.docx
3.3.5 EXPLANATION OF SETUP-MENU 4 - POWER MANAGEMENT
When used with the internal battery option, the user can expect reliable measurement over a long
period of time. The F016-P has several smart power management functions to extend the battery life
time significantly. Two of these functions are available.
SETUP FUNCTIONS AND VARIABLES
4
POWER MANAGEMENT
4.1
LCD NEW
The calculation of the display-information influences the power
consumption significantly. When the application does not require a
fast display update, it is strongly advised to select a slow refresh
rate. Please understand that NO information will be lost; every pulse
will be counted and the output signal will be generated in the normal
way.
The following can be selected:
Fast - 1 sec - 3 sec - 15 sec - 30 sec - off.
Example battery life-time with a coil pick-up:
•1kHz pulse and FAST update: about 2 years.
•1kHz pulse and 1 sec update: about 5 years.
After a button has been pressed by the operator - the display refresh
rate will always switch to FAST for 30 seconds. When "OFF" is
selected, the display will be switched off after 30 seconds and will be
switched on as soon as a button has been pressed.
4.2
BATTERY MODE
The F016-P has two modes: operational or shelf.
After "shelf" has been selected, the F016-P can be stored for several
years; it will not process the sensor signal; the display is switched off
but all settings and totals are stored. In this mode, power consumption
is extremely low.
To wake up the F016-P again, press the SELECT/key twice.
3.3.6 EXPLANATION OF SETUP-MENU 5 - FLOWMETER
The F016-P is able to handle several types of input signal. The type of flowmeter pickup / signal is
selected with SETUP 5.1. Read also paragraph 4.6.1 Terminals 1-3: Flowmeter input.
SETUP FUNCTIONS AND VARIABLES
5
FLOWMETER
5.1
SIGNAL
TYPE OF SIGNAL
EXPLANATION
RESISTANCE
FREQ. / mV
REMARK
NPN
NPN input
100 kΩ pull-up
6 kHz.
(open collector)
NPN - LP
NPN input with
low pass filter
100 kΩ pull-up
1.2 kHz.
(open collector)
less sensitive
REED
Reed-switch input
1 mΩ pull-up
600 Hz.
REED - LP
Reed-switch input
with low pass
filter
1 mΩ pull-up
120 Hz.
Less sensitive
PNP
PNP input
47 kΩ pull-down
6 kHz.
PNP - LP
PNP input with
low pass filter
100 kΩ pull-down
1.2 kHz.
Less sensitive
NAMUR
Namur input
820 Ω pull-down
4 kHz.
External power
required
COIL HI
High sensitive coil
input
-
20 mV p.t.p.
Sensitive for
disturbance!
COIL LO
Low sensitive coil
input
-
90 mV p.t.p.
Normal sensitivity
ACTIVE
Active pulse input
detection level
1.2V DC
47 kΩ
10 kHz.
External power
required

Page 16
FW-F016-P-M_v0404_01_EN.docx
3.3.7 EXPLANATION OF SETUP-MENU 6 - LINEARIZATION
The linearization function is available to approach the real flow curve better as with the general K-
factor (KF0) entered with setup 1.4 and 2.4. This to obtain a more accurate flow rate, total and
accumulated total as well as a pulse output at any flowmeter frequency.
A maximum of 8 linearization positions can be entered while the interpolation will calculate any other
position in between.
For each linearization position, the frequency and a Meter Factor (MF) must be entered.
The Meter Factor for each frequency is calculated with following formula:
Meter Factor
=
K-Factor at Flow rate X
KF0
The lowest frequency and MF you enter will be valid from 0Hz. The highest frequency and MF will
be valid till 10KHz. It is advised to enter the frequencies in increasing order, however it is not
necessary. Please have a look at following example to understand the method of linearization.
Fig. 6: Graphic example of linearization
SETUP FUNCTIONS AND VARIABLES
6
LINEARIZATION
6.1
to
6.8
FREQUENCY / M-
FACTOR
The frequency is displayed at the bottom line of the display.
The maximum frequency is 9,999.9 Hz. With value 0.0Hz, the M-
Factor is disabled. (Please read SETUP 6.A - decimals frequency)
The M-Factor is displayed at the top-line of the display. The minimum
value to be entered is 0.000001 and the maximum value is 9.999999.
Please note that this value has always six decimals while the "dot" is
not displayed.
Most M-factors will be around 1.000000 like 0.945354 or 1.132573.
6.9
DISABLE / ENABLE
With this setup function, you can easily enable / disable the
linearization function.
6.A
DECIMALS FREQUENCY
For the frequency, following decimal positions can be selected:
00000 - 1111.1 - 222.22 - 33.333

Page 17
FW-F016-P-M_v0404_01_EN.docx
3.3.8 EXPLANATION OF SETUP-MENU 7 - PULSE OUTPUT
SETUP FUNCTIONS AND VARIABLES
7
PULSE OUTPUT
7.1
PULSE WIDTH
The pulse width determines the time that the output will be switched;
in other words the pulse length. The minimum time between the
pulses is as long as the period time (50/50 duty cycle).
The pulse width is set in milliseconds in the range 0.001 - 9.999 sec.

If the frequency should go out of range - when the flow rate increases
for example - an internal buffer will be used to "store the missed
pulses": As soon as the flow rate slows down, the buffer will be
"emptied". It might be that pulses will be missed due to a buffer-
overflow, so it is advised to program this setting within its range!
7.2
DECIMALS
This setting determines the decimal position for SETUP 7.3.
The measuring unit is according to SETUP 1.1 Total Unit
7.3
IMPULSE PER
A pulse will be generated every X-quantity.
Enter this quantity here while taking the displayed decimal position
and measuring unit into account.
3.3.9 EXPLANATION OF SETUP-MENU 8 - OTHERS
SETUP FUNCTIONS AND VARIABLES
8
OTHERS
8.1
TYPE / MODEL
For support and maintenance it is important to have information about
the characteristics of the F016-P.
Your supplier will ask for this information in the case of a serious
breakdown or to assess the suitability of your model for upgrade
considerations.
8.2
SOFTWARE VERSION
8.3
SERIAL NO.
8.4
PASS CODE
All SETUP-values can be pass code protected.
This protection is disabled with value 0000 (zero).
Up to and including 4 digits can be programmed, for example 1234.
8.5
TAGNUMBER
For identification of the F016-P and communication purposes, a
unique tag number of maximum 7 digits can be entered.

Page 18
FW-F016-P-M_v0404_01_EN.docx
4 INSTALLATION
4.1 GENERAL DIRECTIONS
•Mounting, electrical installation, start-up and maintenance of this instrument may only be
carried out by trained personnel authorized by the operator of the facility. Personnel must
read and understand this Operating Manual before carrying out its instructions.
•The F016-P may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Make sure that the measuring system is correctly wired up according to the wiring
diagrams. Protection against accidental contact is no longer assured when the enclosure
cover is removed or the panel cabinet has been opened (danger from electrical shock).
The enclosure may only be opened by trained persons authorized by the operator of the
facility.
•Take careful notice of the "Safety rules, instructions and precautionary measures" at the
front of this manual.
The F0-Series can be supplied as suitable for Safe Area or Hazardous Area. This is indicated in the
model code (shown on the product label) by the Type X* designator, with following options:
•Type XX: Suitable for safe area applications only (e.g. F016-P-XX)
Follow the mechanical and electrical installation instructions shown in chapter 4.
•Type XF: Suitable for explosion proof / flame proof applications (e.g. F016-P-XF)
Follow the electrical installation instructions as shown in chapter 4 and
the mechanical installation instructions of the enclosure that are supplied separately.
•Type XI: Suitable for intrinsically safe applications (e.g. F016-P-XI)
Follow the general mechanical and electrical installation instructions of chapter 4
and the specific installation instructions of chapter 5.
4.2 INSTALLATION / SURROUNDING CONDITIONS
Take the relevant IP classification of the
enclosure into account (see identification plate).
Even an enclosure rated for IP67 / TYPE 4(X)
should NEVER be exposed to strongly varying
(weather) conditions.
When used in very cold surroundings or varying
climatic conditions, inside the instrument case,
take the necessary precautions against moisture.
Mount the F-Series onto a solid structure to avoid
vibrations.
For use in Safe and Hazardous Areas (or Locations), the following conditions apply:
Relative humidity:
< 90% RH
Outdoor use:
suitable for outdoor use
IP and NEMA rating:
IP65 (panel mount), IP67 (field mount) and Type 4X
Supply voltage fluctuation:
As indicated by the supply range (e.g. 10V to 30V),
otherwise +/- 10% unless stated otherwise
Means of protection:
Intrinsically safe:
IS
Ordinary locations:
Class I (PE connected metal enclosure)
Class II (non-metallic enclosure)
Over-voltage category:
II (when supplied from mains)
Pollution degree:
2 (internal environment), 3 (external environment)
Ambient:
Intrinsically safe:
-40 °C to +70 °C, -40 °F to +158 °F
(limited to +50 °C, 122 °F for EPL Da)
Ordinary locations:
-40 °C to +80 °C, -40 °F to +176 °F
Altitude:
up to 2000 m

Page 19
FW-F016-P-M_v0404_01_EN.docx
4.3 HANDLING THE F-SERIES ENCLOSURE
4.3.1 IDENTIFICATION
The F0-Series can be supplied as suitable for Safe Area or Hazardous Area.
Suitability for Intrinsic Safety is indicated in the model code by Type XI (e.g. F016-P-XI).
For Intrinsically Safe applications: Installation and identification labels are shown in chapter 5.
Identification label
To identify your F0-Series device, all field mount enclosures have a weatherproof identification label
placed on the outside of the unit.
Fig. 7: Identification Example of F0-Series identification label (safe area)
Installation label
A second label is located on the inside and shows additional installation data. For panel mount
enclosures, the outside label is not available, so the inside label also serves as identification label.
After installation, the inside label is only visible from the rear side of the panel.
Fig. 8: Identification Example of F0-Series installation label (safe area - Type PB, PX or PD)

Page 20
FW-F016-P-M_v0404_01_EN.docx
Fig. 9: Identification Example of F0-Series installation label (safe area - Type PM or PF)
Serial number and year of production
The serial number can be reviewed on the identification label or in
SETUP-menu Others. The production date is either shown separately on
the label or indicated by the first 4 digits of the serial number
representing year and week number (YYWW).