Flymo Power Hoe User manual

®
IMPORTANT INFORMATION
Read before use
& retain for future reference
INSTRUCTION MANUAL

1
CONTENTS
Carton Contents
IMPORTANT !
Please check the contents of the carton are
correct BEFORE assembling your new Flymo
product.
IF ANY PARTS ARE MISSING CONTACT:-
Electrolux Outdoor Products Customer Service
Department direct
Telephone : [phone]
Fax : [phone]
LIST OF INSTRUCTION MANUAL
CONTENTS
CONTENTS (1)
SAFETY (2-4)
PREPARATION (5)
USE (6-7)
MAINTENANCE (8-9)
GUARANTEE (10)
CERTIFICATE
OF CONFORMITY (11)
ENVIRONMENTAL
INFORMATION (12)
A
instruction
manual
guarantee card
switch lever
steady handle
handle bolt
multi-purpose
tine
speed control
handle knob
tine collar mains cable

2
SAFETY
Explanation of Symbols on the Power Hoe.
Warning.
Read the user instructions
carefully.
Switch off! Remove plug from
mains before adjusting, cleaning
or if cable is entangled or
damaged. Keep the cable away
from the tine.
Do not operate whilst people,
especially children, or pets are in
the hoeing area
Tines continue to rotate after the
machine is switch off, rotating
tines can cause injury
Do not operate in the rain or
leave the Power Hoe outdoors
while raining.
General
1. Never allow children or people unfamiliar
with these instructions to use the Power
Hoe. Local regulations may restrict the age
of the operator.
2. Only use the Power Hoe in the manner and
for the functions described in these
instructions.
3. Never operate the Power Hoe when you are
tired, ill or under the influence of alcohol,
drugs or medicine.
4. The operator or user is responsible for
accidents or hazards occurring to other
people or their property.
Electrical
1. The British Standards Institute recommend
the use of a Residual Current Circuit
Breaker (R.C.C.B.) with a tripping current of
not more than 30mA. Even with a R.C.C.B.
installed 100% safety cannot be guaranteed
and safe working practice must be followed
at all times. Check your R.C.C.B. every
time you use it.
2. Before use, examine cable for damage,
replace it if there are signs of damage or
ageing.
3. Do not use the Power Hoe if the electric
cables are damaged or worn.
4. Immediately disconnect from the mains
electricity supply if the cable is cut, or the
insulation is
damaged. Do not
touch the electric
cable until the
electrical supply has
been disconnected.
Do not repair a cut
or damaged cable.
Replace it with a
new one.
5. Your electric cable
must be uncoiled, coiled cables can
overheat and reduce the efficiency of the
Power Hoe.
6. Keep cable away from the tine area.
7. Do not pull cable around sharp objects.
If not used properly this Power Hoe can be dangerous! This Power Hoe can
cause serious injury to the operator and others, the warnings and safety
instructions must be followed to ensure reasonable safety and efficiency in using
this Power Hoe. The operator is responsible for following the warning and safety
instructions in this manual and on the Power Hoe.

3
SAFETY
8. Always switch off at the mains before
disconnecting any plug, cable connector or
extension cable.
9. Switch off, remove plug from mains and
examine electric supply cable for damage
or ageing before winding cable for storage.
Do not repair a damaged cable, replace it
with a new one. Use only Flymo
replacement cable.
10. Always wind cable carefully, avoiding
kinking.
11. Never pull on the cable to disconnect any of
the plugs.
12. Use only on AC mains supply voltage
shown on the product rating label.
13. Flymo products are double insulated to
EN60335. Under no circumstances should
an earth be connected to any part of the
product.
Preparation
1. Always wear suitable clothing, gloves, and
stout shoes. The use of eye protection is
recommended. Do not wear loose clothing
or jewellery which can be caught in moving
parts.
2. Thoroughly inspect the area where the
Power Hoe is to be used and remove all
wires and other foreign objects.
3. Before using always visually inspect to see
that the tine is not worn or damaged.
Use
AVOID ACCIDENTAL STARTING. WHEN
CLEARING DEBRIS FROM THE TINE AREA,
REMOVE PLUG FROM MAINS AND KEEP
FEET AWAY FROM THE SWITCH LEVER.
1. Use the Power Hoe only in daylight or good
artificial light.
2. Ensure that shoe laces are tied correctly
and are kept clear of the rotating tine.
3. Do not use the Power Hoe when it is raining
or in damp and wet areas.
4. Never use the Power Hoe in or near water
or ponds.
5. Take extra care when working near shrubs
and bushes to prevent the tine becoming
entangled.
6. Know how to stop the Power Hoe quickly in
an emergency.
7. On slopes, be extra careful of your footing
and wear non-slip footwear.
8. Always start the Power Hoe carefully with
feet well away from the tine.
9. Never pick up or carry the Power Hoe by
the cable.
10. Keep the tine below waist level.
11. Avoid operating while people, especially
children, are nearby.
12. Keep cable away from tine at all times. If
cable becomes entangled, remove plug
from mains and carefully inspect cable for
damage. If in doubt, contact your local
Dealer.
13. Remove the plug from the mains :-
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be
sure the Power Hoe is in safe working
condition.
2. Replace worn or damaged parts for safety.
3. Be careful during adjustment of the Power
Hoe to prevent entrapment of the fingers
between moving and fixed parts of the
machine.
4. After use the Power Hoe should be stored
in a safe place where it is protected from
damage.
- before leaving the Power Hoe
unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working
on the appliance;
- if you hit an object. Do not use the
Power Hoe until you are sure that the
entire Power Hoe is in a safe operating
condition;
- if the Power Hoe starts to vibrate
abnormally. Check immediately.
Excessive vibration can cause injury.

CABLES
IMPORTANT
•Use only a minimum 1.00mm2 size cable up
to 60 metres length maximum for the Power
Hoe.
1. Flymo products are supplied with either an
electric mains cable fitted with a female
connector or with an electric mains cable
wired directly into the product.
THE POWER HOE IS SUPPLIED WITH AN
ELECTRIC MAINS CABLE WIRED
DIRECTLY INTO THE PRODUCT.
2. Flymo Mains Cables and Extension Cables
are available from your local Electrolux
Outdoor Products Approved Service Centre.
3. Do not wire an extension cable directly to
your product yourself. Please contact your
local Electrolux Outdoor Products Approved
Service Centre for further information on the
connectors and kits available.
4. Only use extension cables specifically
designed for outdoor use.
CONNECTORS
IMPORTANT
•Flymo connectors are suitable for use with
2 core cable only. Under no circumstances
should these connectors be used for
earthed products.
•All Flymo connectors and cables are of
splashproof construction. They are not
waterproof and must not be left outside
permanently nor should they be submerged
or immersed in water. Do not let cable lay
or trail through pools of water or splashed
with water from hose pipes.
MAINS PLUG REPLACEMENT
IMPORTANT
• If the plug supplied is cut off it should
be destroyed. There is an electric shock
hazard if a cut off plug is inserted into a
13 amp socket.
1. No earth required. Flymo products are
double insulated to EN60335 and under no
circumstances should an earth be
connected to any part of the product.
2. Ensure the mains voltage suits your
product
3. IMPORTANT!
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
The wire which is coloured BLUE must be
connected to the Terminal which is marked
with the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must
be connected to the Terminal which is
marked with the letter 'L' or coloured RED.
4. It is important that the outer sheath is
clamped correctly into the 3-pin plug.
5. If in doubt consult your local Service
Repairer or qualified electrician before the
machine is used.
6. A 5 Amp fuse must be fitted to the Mains
Plug.
7. The normal plug fuse and household fuse
only protect the electrical equipment and
are not a safeguard against electrocution.
Electric mains
cable fitted with a
female connector
For further information on Mains Cables, Extension Cables, Cable Connectors and kits
contact Electrolux Outdoor Products Customer Service direct:-
Telephone : [phone]
Fax : [phone]
E
L
F
U
S
E
N
BLACK
OR
BLUE
RED
OR
BROWN
SAFETY
4
Electric mains
cable wired directly
into product

5
ASSEMBLY
Your product is uniquely identified by a silver
and black product rating label.
To ensure you have full product information
when obtaining spares or advice from one of
our approved service centres, or if you need
to contact our customer service department,
you should make a note in the space
provided of the information shown in fig.B. It
will also be useful to make a note of the date
and place of purchase before you return
your guarantee card.
Product Rating Label
Assembly & Adjustment
Fitting the Tine
• Use the same procedure for
fitting the Multi-purpose Tine and
the Raking Tine Attachment.
1. Line up the tine collar as
illustrated in Fig. C.
2. Place the tine onto the shaft as
illustrated in Fig. D.
3. Turn the tine collar clockwise, as
illustrated in Fig. E, until it
locates into place.
• Removal is the reverse
procedure. Ensure the tine
collar is clean and free from dirt
before refitting.
Fitting the Steady Handle
1. Attach the steady handle to your
product using the bolt and
handle knob as shown in Fig. F.
Steady Handle Adjustment
1. To adjust the steady handle to a
new position, loosen handle as
shown in Fig G and move
handle to one of the three
positions as shown in Fig H.
2. Re-tighten handle knob.
Product Number . . . . . . . . . . . . . . . .
Model. . . . . . . . . . . . . . . . . . . . . . . . .
Serial . . . . . . . . . . . . . . . . . . . . . . . .
Date of Purchase . . . . . . . . . . . . . . . .
Place of Purchase . . . . . . . . . . . . . . .
•PLEASE KEEP PROOF OF PURCHASE•
B
D E
C
F
G H
✓✓✖✖

6
USE
To start the Power Hoe
1. Form a loop in the mains cable
and push the loop through the
slot as illustrated in Fig J1.
2. To secure, position loop over the
hook (J2) and pull the cable
back through the slot (J3).
3. Connect plug to mains and
switch on.
4. For slower speeds see note,
move rocker switch forward with
thumb and squeeze switch lever
on handle (See Fig. K). Keeping
the switch lever squeezed, the
thumb can be removed from the
rocker switch.
5. For faster speeds see note,
rocker switch backward with
thumb and squeeze switch lever
on handle (See Fig. L). Keeping
the switch lever squeezed, the
thumb can be removed from the
rocker switch.
6. When the Power Hoe has
reached required speed, gently
lower it into the soil.
•Note
The speed can be varied by
slightly releasing pressure on
the switch lever. (Fig M)
To stop the Power Hoe
1. Fully release the pressure on the
switch lever. (Fig. N)
Starting & Stopping
J
1
2
1
2
K
L
M
N
1 2
3

7
USE
How to use the Power Hoe
•Grip the Power Hoe firmly, with
two hands, when operating.
1. Choose the speed required (See
Starting & Stopping), break up
the soil by using a stabbing
movement as illustrated in Fig.
P.
2. Move the machine from side to
to side to evenly hoe the soil.
(Fig Q)
3. To remove weeds, place the
machine in the soil at an angle
next to the weed (See Fig R).
4. When using the Power Hoe
close to plants, it is
recommended to use the slower
variable speed. (See Fig. S.)
Recommended Use.
The Multi-purpose tine is ideal for
turning, aerating, loosening,
weeding and cultivating your soil.
How to Use
P
Q
R
S

8
MAINTENANCE
Caring for the Power Hoe
•Avoid accidental starting.
When clearing debris from
tine area, remove plug from
mains and keep feet away
from switch lever. (See Figs T
& V)
Cleaning (W)
•USE GLOVES
1. Wipe over the surface of the
Power Hoe with a dry cloth.
2. Using a soft brush remove
debris from all air intakes and
tine area.
•IMPORTANT
Never use water for cleaning the
Power Hoe. Do not clean with
chemicals, including petrol or
solvents, some can destroy
plastic parts.
Caring
1. Check that all nuts and bolts are
tight.
2. Visually inspect the Power Hoe
for any worn or damaged parts,
contact your local Service
Centre if any parts require
replacement.
Storing.
1. Store in a dry place where the
Power Hoe is protected from
damage.
2. The steady handle on the Power
Hoe can be used to hang the
product on the wall as illustrated
in Fig. X.
•IMPORTANT
Avoid accidental damage, do not
leave the Power Hoe leaning
against a wall where it could fall
over.
T V
W
X

9
MAINTENANCE
1. We strongly recommend that your
product is serviced at least every twelve
months, more often in a professional
application.
2. Always use genuine Flymo Spare Parts.
3. Pre-packed spares are available from
most Electrolux Outdoor Products
stockists.
4. If you have a problem with your machine
contact your local Electrolux Outdoor
Products Approved Service Centre
ensuring you have full details of your
product as described on the product
rating label.
5. Should it be necessary for work to be
carried out by your Electrolux
Outdoor Products Service Centre, it is
important to take your complete
machine including cable and any
extension cables used.
6. In the event of further difficulty please
contact:-
Electrolux Outdoor Products
Customer Service
Preston Road
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co. Durham
DL5 6UP
Telephone: [phone]
Fax : [phone]
A network of specialist dealers can be found
in your local Yellow Pages.
To obtain service on your Flymo product
simply telephone or visit your local Service
Centre.
Should you require service under the terms
of our guarantee the Service Centre will
require proof of purchase.
All of the centres listed stock genuine
Flymo Spare Parts.
NOTE:
Our Service Repairers act on their own
behalf and are not empowered to commit
or legally bind Electrolux Outdoor
Products in any manner whatsoever.
Fault Finding Hints & Service Recommendations
Service Recommendations Fault Finding Hints
Fails to Operate
1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
Fails to stop when switch lever is released.
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
Poor hoeing quality
1. Ensure the product is being used correctly (see
How to Use)
2. Ensure tine is free from trapped debris
3. Damaged tine?
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.
Excessive Vibration
Immediately disconnect from the mains
electricity supply and consult your local
approved Service Centre.