FlyTech K736 User manual

USER MANUAL
VERSION 2.1 October 2021
Panel PC
Hardware System

ii
Copyright 2021
All Rights Reserved
Manual Version 2.1
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose.
We shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated
to another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation
to ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register or in a built-in installation
unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a re or electric
shock. Never spill liquid of any kind on the product.
10.To avoid the risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.
11.No modication of this equipment is allowed.
12. Power supply is specied as part of medical equipment.

iii
13. The medical PC can be cleaned in accordance with normal clinical cleaning practices,
including wiping with water or medical grade wipes, provided no substance containing
acids or cleaning alkali liquids is used.
14. Medical grade wipes must not contain more than 80% alcohol content measured
against the total content of the wipe.
15. Operator shall not contact patient simultaneously when in use with the medical
computer.
Sécurité
INSTRUCTIONS IMPORTANTES RELATIVES À LA SECURITE
1. Pour débrancher la machine de l’alimentation électrique, éteignez l’interrupteur
d’alimentation et retirez le cordon d’alimentation de la prise murale. La prise murale
doit être facilement accessible et à proximité de la machine.
2. Lisez attentivement ces instructions. Conservez ces instructions pour une référence
future.
3. Suivez tous les avertissements et les instructions indiquées sur le produit.
4. Ne pas utiliser ce produit à proximité de l’eau.
5. Ne pas placer ce produit sur un chariot, un support ou une table. Le produit peut
tomber,causant de graves dommages à l’appareil.
6. Les fentes et les ouvertures dans le boîtier, l’arrière ou le fond sont prévues pour
la ventilation an d’assurer un fonctionnement able du produit et le protéger de la
surchauffe. Ces ouvertures ne doivent pas être obstruées ou couvertes. Les ouvertures
ne doivent jamais être bloquées en plaçant l’appareil sur un lit, un canapé, un tapis
ou autre surface similaire. Ce produit ne doit jamais être placé : à proximité ou sur un
radiateur, sur un registre de chaleur ou dans une installation intégrée à moins qu’une
ventilation adéquate soit prévue.
7. Ce produit doit être utilisé avec le type d’alimentation indiqué sur l’étiquette.Si
vous n’êtes pas sûr du type d’alimentation disponible, consultez votre revendeur ou
représentant local de l’entreprise.
8. Ne laissez rien reposer sur le cordon d’alimentation. Ne placez pas ce produit là oùdes
personnes peuvent marcher sur le cordon.
9. N’introduisez jamais d’objets d’aucune sorte dans ce produit à travers les fentes du
coffret car ils pourraient entrer en contact avec des points sous tension dangereux ou
court-circuiter des pièces. Ne renversez jamais de liquide d’aucune sorte sur le produit.
10.Pour éviter tout risque de choc électrique, cet équipement ne doit être branché que sur
une prise secteur avec terre.
11.Aucune modication de cet équipement n’est autorisée.
12.L’alimentation est spéciée comme faisant partie du matériel médical.
13.L’ordinateur médical peut être nettoyé conformément aux pratiques de nettoyage
cliniques habituelles, notamment en essuyant avec de l'eau ou des lingettes de qualité
médicale, à condition qu'aucune substance contenant des acides ou des liquides de
nettoyage alcalins ne soient utilisés.
14.Les lingettes de qualité médicale ne doivent pas contenir plus de 80% d'alcool par
rapport au contenu total de la lingette.
15.L’opérateur ne doit pas toucher le patient lorsqu’il utilise l’ordinateur médical.

iv
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery
according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, peripherals shall be 4.7.3.2 “Materials for re enclosure” compliant.
4.7.3.2 Materials for re enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a
FIRE ENCLOSURE, in the thinnest signicant wall thickness used, shall be of V-1 CLASS
MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY
EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall
thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
AVERTISSEMENT SUR LES BATTERIES AU LITHIUM
Il y a un danger d’explosion si la batterie n’est pas remplacée correctement.
Remplacez-la uniquement par une batterie identique ou de type équivalent
recommandée par le fabricant.les batteries usagées doivent être mises au rebut
conformément aux instructions du fabricant.
CE MARK
This device complies with the requirements of the EEC directive 2014/30/EU with
regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.

v
Pour équipements mobiles ayant une masse totale supérieure à 18 kg et pour tous les
équipements FIXES :
Les matériaux d’un équipement coupe-feu dans l’épaisseur de paroi retenue la plus
signicativement mince, doivent être des matériels de CLASSE V-1, doivent être de
classe Matériel 5VB ou doivent passer le test de l’article A.1
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centers for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government ofce, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
Avertissement Batterie
Risque d’explosion si la batterie est remplacée par un élément incompatible.
Jetez les batteries usagées selon les instructions des dispositions locales .
Avertissement de sécurité
Remarque: Pour répondre à la norme IEC60950-1 alinéa 2.5 (sources d’énergie limitées,
LPS) liés la législation, les périphériques doivent être conforme 4.7.3.2 “Matériaux pour
enceinte coupe-feu»
4.7.3.2 “Matériaux pour équipements coupe-feu»
Pour les équipements mobiles ayant une masse totale n’excédant pas 18kg :
Les matériaux d’un équipement coupe-feu, dans l’épaisseur de paroi retenue la plus
signicativement mince, doivent être des matériels de CLASSE V-1 ou doivent passer le
test de l’article A.2.

vi
Troubleshooting
For your own safety and that of your equipment, always take the following precautions.
Disconnect the power plug (by pulling the plug, not the cord), from your computer if any
of the following conditions exists:
• The power cord or plug becomes frayed or otherwise damaged.
• You spill something into the system.
• Your computer has been dropped or damaged.
• You suspect that your computer needs service or repair.
• You want to clean the computer or screen.
• You want to remove/install any parts.
Repair of the device may only be carried out by the manufacture.
We recommend that a service contract be obtained with supplier and
that all repairs also be carried out by them. Otherwise the correct
functioning of the device may be compromised.

vii
Revision Description Date
1.0 • Initial release June 2020
1.1 • F14 motherboard added
• PoE module added August 2020
2.0 • F64U motherboard added November 2020
2.1
• F64U motherboard removed
• F34 motherboard added
• New camera peripheral added
October 2021
Revision History
Changes to the original user manual are listed below:

viii
Table of Contents
1. Packing List.................................. 1
1-1. Standard Items................................................................1
1-2. Optional Items .................................................................2
2. System View.................................. 3
2-1. Front & Side View ............................................................3
2-2. Rear & Bottom View ........................................................3
2-3. I/O View ...........................................................................4
2-4. Dimensions......................................................................5
3. System Assembly ......................... 7
3-1. Powering On & Off...........................................................7
3-2. Remove the Cable Cover ................................................7
3-3. Remove the Motherboard Box........................................8
3-4. Replace the RAM Module...............................................9
3-5. Replace the M.2 SSD Card............................................11
4. Peripherals Installation .............. 12
4-1. Install the MSR/ Fingerprint/ NFC / 2D Scanner Module .12
4-2. Install the WiFi Dongle Module .....................................13
4-3. Install the Antennas .......................................................14
4-4. Install the PoE Module...................................................14

ix
5. Specication................................ 15
6. Conguration............................... 18
6-1. D84U Motherboard .......................................................18
6-1-1. Motherboard Layout........................................................18
6-1-2. Connectors & Functions .................................................19
6-1-3. Jumper Setting ................................................................20
6-2. F14 Motherboard ..........................................................24
6-2-1. Motherboard Layout........................................................ 24
6-2-2. Connectors & Functions .................................................25
6-2-3. Jumper Setting ................................................................26
6-3. F34 Motherboard ..........................................................29
6-3-1. Motherboard Layout........................................................29
6-3-2. Connectors & Functions .................................................30
6-3-3. Jumper Setting ................................................................ 31

1
1. Packing List
1-1. Standard Items
a. System
b. Power adapter
c. Power cord
a. b.
c.
Note: Power cord will be supplied differently according to various region or country.

2
1-2. Optional Items
a. b.
c. d.
e. f.
g. h.
i.
a. MSR
b. Fingerprint
c. 2D scanner
d. NFC
e. Camera
f. Light bar
g. Wall mount kits
h. PoE module
i. Antenna (x2)

3
2. System View
2-1. Front & Side View
Item No. Description
1 Touch panel
2 Speaker
3 MSR / Fingerprint / NFC / 2D scanner
2-2. Rear & Bottom View
Item No. Description
1 Dummy cover of MSR/ Fringerprint/ Scanner
2 75 x 75 mm /100 x 100mm VESA mounting holes
3 Power button
4 Cable cover
1
3
2
1
1
2
3
4

4
2-3. I/O View
No. Description
a FeDP (2nd display)
b LAN
c DC 19V in
d USB 2.0 x 2
e USB Type C x 2
f USB 3.0 x 2
g COM x 2
h Cash drawer
i FeDP (Main display)
a b cdefghi
D84U & F34 Motherboard
No. Description
a FeDP (2nd display)
b LAN
c DC 19V in
d USB 2.0 x 2
e USB Type C
f USB 3.0 x 2
g COM x 2
h Cash drawer
i FeDP (Main display)
a b cdefghi
F14 Motherboard

5
42 mm
370 mm
384 mm
235 mm
K737 - 15.6” LED panel
2-4. Dimensions
41 mm
277 mm
195 mm
181 mm
K736 - 11.6” LED panel

6
49 mm
519 mm
533 mm
311 mm
K739 - 21.5” LED panel
K738 - 18.5” LED panel
51 mm
451 mm
467 mm
273 mm

7
3. System Assembly
3-1. Powering On & Off
To activate the system, push and quickly release the power button and the display will
come on in a few seconds. NOTE: The system must be plugged into power adapter
before turning on for the first time.
To turn off the system, power off the device safely using software function that “shuts
down computer” provided in the operating system.
3-2. Remove the Cable Cover
1. Turn to the back side of the system
and loosen the screws (x2) to release
the cable cover.

8
1. To remove the motherboard box, please remove the cable cover firstly as steps
dscribed in chapter 3-2.
2. Unplug the FeDP cables (x2) connected directly to the ports on the I/O panel.
Always power down the system before releasing the cables or it may cause
damage to the motherboard inside.
3-3. Remove the Motherboard Box
3. Push the plastic holder of the motherboard box and pull it outward to release the
motherboard box from the system.

9
3-4. Replace the RAM Module
K736 Model
1. To replace the RAM, please remove
the cable cover firstly as steps
dscribed in chapter 3-2.
2. Remove the screws (x10) to open
the rear cover of the touch panel.
3. Remove the screws (x4) of the metal
bracket to access the motherboard.
Removing a RAM module
1. Flip the ejector clips outwards to
remove the memory module from
the memory slot.
Installing a RAM moudle
2. Slide the memory module into the
memory slot and press down until
the ejector clips snaps in place.

10
Removing a RAM module
1. Flip the ejector clips outwards to
remove the memory module from
the memory slot.
Installing a RAM moudle
2. Slide the memory module into the
memory slot and press down until
the ejector clips snaps in place.
1. To replace the RAM, please release
the motherboard box firstly as steps
dscribed in chapter 3-3.
2. Remove the screws (x5) to open
the metal cover of the motherboard
box.
3. Find the RAM module located at the
right side of the motherboard.
K737 / K738 / K739 Model

11
3-5. Replace the M.2 SSD Card
1. To replace the RAM, please release the motherboard box firstly as steps dscribed
in chapter 3-3 (K737/K738/K739) and 3-4 (K736).
2. Remove the screws (x1) and pull the M.2 SSD card outwards as shown in the
picture.